Ford F-150 - 1997-2003 :: Truck Won't Communicate With Code Reader
Oct 29, 2012
Truck had a rich on bank 2 code about a month ago, I cleared it and the service engine light stayed off for quite some time.
Last friday on the way home from work the truck started shaking badly right from idle, and at one point on the freeway the service engine started flashing. I couldn't pull over as I was on a bridge but once I dropped my speed the light stayed on but the flashing stopped.
I went to plug the truck in today and first shot it didn't communicate with the code reader at all, I talked to someone who told me that the cigerette lighter fuse is also the OBD port fuse, I pulled a fuse from somewhere else and plugged the reader in again. This time it started communicating with the truck but didn't display any codes while all the while the truck is miss firing and the service engine light is lit up on the dash.
One other weird thing: The fuse had an LED indicator to show that it is blown, when I push the cig lighter in the led gets a hell of a lot brighter, if there is always power drawn through the circuit shouldn't the LED be constantly bright all the time? I'm wondering if there is a short somewhere. Where to look next??
View 2 Replies
Advertisement
2000 F150 V6 auto just bought it 140k. Check engine light on.. Code reader wont come on? has 2 lighter sockets in dash one on the left works right one dont? I hear one is inline with the code port? Checked 1 fuse #110? looked good...I don't have a manual so I"m lost.. or there are more fuses?
Also the speedo mileage sometimes will go blank? at start up then come back on ?? seems to be working even when blank? First I need to get the code reader port to put out..so i can see the codes....
View 4 Replies
Me and the wife got in the ole '97 1.8. After may be 5 mins or so, I noticed the CEL was on.
I've only ever seen the CEL light on once, and it was b/c the gas cap was loose.
The car ran fine, nothing out of the ordinary. After getting home, I plugged in the dusty OBD reader thingy and it spit out a code, I can't remember. P401 or something like that. EGR emission low?
It appeared that my EGR valve is all cruddy with carbon deposits. So Is removal/cleaning terribly difficult? I'm thinking some carb cleaner and maybe a scraper would do the trick.
View 9 Replies
I am trying to find out how many o2 sensors are suppose to be on my 2003 excursion? I am getting two codes on my OBD reader, an "o2" and an "o2 heater" code flashing...... I have replaced both the o2 sensors i found, both were at the exhaust manifolds.
View 14 Replies
Ok, did a quick search, found nothing. Is there a way to get CEL codes without a reader on '01 F150? I know the way on 80's stuff, is there on newer stuff?
View 2 Replies
I was involved in a light accident over the weekend. I was hit in the rear by a Prius which didn't do body damage except for the 7 blade harness for my trailer towing. But, now the truck has a random misfire code. You can feel the truck jerk when you go up any grade. We changed the fuel filter and dumped in some cleaner already. One guy says its fuel and one thinks its coils. It is a 2003 F150 extended cab 5.4 with a nearly new motor. The truck has about 175xxx on it and I have had it for about 40xxx. I have not changed coils. We did check the inertia switch on the passenger side and it was not tripped.
View 2 Replies
I have a 1999 F-150 with the 4.2L engine. I recently did a motor swap as the original motor was bad. I bought this truck as a project truck and have enjoyed working on it.
When I did the engine swap back in May of this year, it took a while to work out all the little bugs and quirps. However, after a while of running the truck it threw a few codes. I replaced a lot of the emission components and no more codes for several months until last month the truck started throwing the infamous P0174 "too lean bank two"... I have replaced the pcv valve and all the hoses to include the little rubber boot under the front of the intake, all 4 O2 sensors, MAF sensor, EGR, DPFE, IAC valve, new wires and plugs to include coil pack, fuel pressure regulator, and all the vacuum lines that are under the hood.
The truck runs fine, has power, but about every couple weeks or so it throws this P0174 code. I know there are alot of threads on here about this problem and I have read many of them. It only throws the P0174 and not the P0171. I am wondering if there could be a problem specific to "bank 2" that I am over looking.
View 2 Replies
I have a 2001 F150 XLT Supercab,4.2lt, automatic, 2WD.
I was able to start it about a month or so ago but it was really hard to start. I had to use starting fluid to get it started, and it was still tough to get it to start, but once started and warmed up it ran fine.
Now I tried to start it again and it kicks over and wont start. I tried the same with the starting fluid and it almost starts and dies. I think I used a little too much starting fluid because after a while of trying and spraying starting fluid, I got a hard backfire that sounded like a shotgun that was strong enough to pop off the MAF Sensor and throw it about 10 feet. I nearly crapped my pants! It looks clean and undamaged but I hope I didn't damage the MAF Sensor when if hit the ground.
The truck sounds like its starving for fuel, so I'm not sure if the fuel pump relay is going or has gone bad, or if its the fuel pump. How to check these items without making it a huge project to diagnose?
Once I can get it to start easily, I have a couple of questions about the trouble code that keeps coming back P0174. That was the original problem with it before the starting problem.The diagnostic says that it is lean in bank 2 but a mechanic friend of mine said something about a vacuum leak.
View 1 Replies
I have a 1997 Ford F-150 with the 4.6L auto trans 189,000 miles
Ok.. there was no problems until the other day when I unplugged the positive side of the battery to replace it's clamp. I Put the new one on and drove to the store but when I came to a stop, the rpm's dropped to 0 and the truck died. I restarted it and every time I would come to a stop it would die unless I give it a little gas also if I start the truck and leave it in park it idles fine until I give it some gas then let off.. the idle drops and dies! If I give it a little steady gas the idle will return to normal.
The check engine light works fine but never once lit up because of this problem! I used a code scanner and if the truck was off and the key forward, it would have no codes. With it running it had the code P0443. I found and replaced a blown fuse and still have the same problem but it reads no codes at anytime. I checked all the vacuum hoses and there seems to be no leaks and the mass airflow sensor looks clean. I have allot of miles but it has been taken care of well and has had a ton of parts replaced over the last few years.
I am wondering why this happened out of the blue and If there is something I am missing that I should be looking at. I don't want to replace the purge control valve if thats not the problem.
View 2 Replies
I have a 1999 F150 with a 5.4L. I recently replaced the PCM with a new unit from autocomputerexchange.net that was programed for my truck. I installed the PCM but the truck did not start. The theft light is also flashing rapidly during cranking. I ran a code scanner a recieved the code P1260 indicating an attempted theft which disabled the truck. I read that if you have two keys you can sync the keys with the new computer but unfortunately one of the keys stopped working a couple years ago (not sure why, stopped for gas and it never started back up). Since i do not have two working keys do i have to tow the truck to a dealer and let them reprogram the keys and reset the PATS or can i have a locksmith recode the keys and sync the keys myself.
View 2 Replies
I have a 2000 f150 with 5.4 Triton with 165k miles. I did invest in a code reader. It started missing and code P0302 came up along with P0171. Put new coil on #2 and truck ran fine for a few days. Then it started to run rough again. Shaking, Idle rough, no power and CEL came on again. This time code P0171. I changed out fuel filter to no avail. My next step was to start looking for vacuum leaks. As I'm searching, All I am finding is trucks with this problem also get P0174 code. My question is since I am only getting lean on one bank does that pretty much eliminate things like MAF or the famous elbow vacuum leak and make something that only affects one bank like an O2 sensor on CAT more likely?
View 2 Replies
I have a 2000 f150 with a 5.4 past few months it has been throwing a p1151 code meaning it is coming up lean on the driver side. I just changed the plugs and it didn't work, neither did changing the fuel and air filters. cant find any vacuum or exhaust leaks. Replaced a bad injector along with the spark plugs and its still coming up lean.
The truck also seems to bog down at about 50-60 mph if i let off the gas and coast it will drop about 300 rpms. It has me confused and annoyed, i have true duals with glass packs could that be causing it?
View 4 Replies
2007 Ford explorer 4x4 V8, U0101 Failure to communicate with the TCM
Vehicle shifts very hard when under load then and when the Traction control light and the "wrench" light come on it seems to be stuck in high gear, if I stop it takes off like in high gear and never shifts, when I do an ignition cycle then the lights go off and it takes off in first gear and shifts as normal unless it's under load it will bang in and out of gear. Where is the TCM located? On a side note I do hear air like vacuum behind the center console when I press the pedal. Not sure if it has always done this or not.
View 10 Replies
I am trying to run some diagnostics and get codes for my truck. Problem is the scanner won't communicate with the trucks computer. It's the usb elm 327connector and Iam using the forscan program.
Changed to ciggar lighter fuse. still not working. I think the previous owner had a edge program in it idk if that might of fried the pcm or is causing it not to read right? Do I need a better connector or are the pins inside the trucks communicater bad ?
View 14 Replies
I have a 2004 chevy silverado 1500 ext cab with a 5.3 L 4X4 , I tried to plug in a code reader and I'm not getting any readings . The reader is working , My question is can this be fixed by me or do I have to take my truck into the dealer?
View 7 Replies
Title says it, I just installed my Hydra Chip, now my edge says it cant communicate with PCM. I have checked all the connections on the edge, all is good. I planned on just using the Edge only for gauges. Will it not work anymore now that I have a Hydra? If not I will just sell it and buy an Edge Insight, so long as that will work.
I think its the Edge EVO 2, its this one.
View 5 Replies
I am told I am possibly having some engine misfires and I need to get my error codes read. The problem is I don't want to drive the car to an auto parts store to get read because the engine is really rough and bumpy. So what kind of code reader to get, OBD I, OBD II, CAN..etc??? I have a 2000 Buick Park Ave. I have a mechanic coming over tomorrow, and it seems he doesn't have a code reader off hand, so I gotta pick one up...
View 4 Replies
When I want to start the truck dix nothing and I don't know why? I have to tell you that I have changed my tranny ...
View 3 Replies
2002 Model, F150, 4.6L Triton....
Early last week one day my truck just wouldn't start. I had driven it the day before. but that day nothing. It would spin over just not start. the following day though, it started as always, no hesitation and run smooth. But the was the last day it has ran.
Since then I have checked the relays and fuses. I have checked the inertia switch (pass. side kick panel). Removed the cap on the schrader valve on the fuel rail. (no pressure)
I have sprayed starting fluid into the throttle body and it starts for 1 to 2 seconds. (dies once starting fluid is gone). I have changed the fuel filter and pulled the bed and changed out the fuel pump. I'm thinking about trying the fuel pressure regulator next.
Just not real sure where else to go if that doesn't work.....
View 8 Replies
What are the parts of the truck that should be greased? I'm about to do a front, transfer and rear differential fluid change..
View 2 Replies
I have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 Replies
