I have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 RepliesI have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 RepliesI have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 Replies2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
Today at a light my truck wouldn't upshift. I can manually shift from low to second but not to drive. Reververse works fine. I was noticing a slight slip between 45 & 55mph and would sometimes go away if I disingaged the overdrive.
View 2 RepliesI have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 RepliesI was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 RepliesI have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 RepliesI have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 RepliesMy truck was working fine and I drove it to school one day and I was driving and I noticed the RPM was high and the truck wasn't moving correctly luckily I made it home and parked it now it won't move at all I can shift into gears and I put it in first and reverse and let off the clutch and it doesn't move like the clutch is still disengaged. The Slave Cylinder is pressing against the pressure plate to disengage the clutch and then releasing. I have a single cab 1999 Ford F150 4.2 V6.
View 3 Replies97 F150 4.9 200xxx 5 Speed .....
I'm having an issue with my truck. It only seems to happen during warm 80+ weather. In the mornings, and during colder weather, the truck runs perfectly.
My problem is; Every time I go to get going and feather the clutch, either in 1st or reverse, my truck bucks wildly.
I changed the plug wires about 500 miles ago, and am about 4000 miles on a rebuilt engine (plugs as well) and new clutch/resurfaced flywheel. The clutch reservoir is full and I haven't noticed any leaks. There have been no codes thrown.
Could it be a possible fuel problem? I think I changed the fuel filter about 7k-10k miles ago.
I was also wondering if the Gotts mod could be causing it. I did the mod during the winter time, and this is my first summer with it on. My air filter is fine.
My truck does not go into reverse but thinks all positions of shifter are drive. I had some slippage and changed the filter and oil great for awhile then blame no reverse just forward I was told my torque converter was out I just don't know....
View 1 RepliesJust finished putting a fresh 460 backed by a (1977) c6 in my '68 ranger and now I'm having (what I believe is) transmission problems. The truck will idle and rev properly in gear but as soon as I put it in drive or reverse the RPM's drop and it dies. I jacked the back end up and put it in both drive and reverse and the tire's spin, but if I try and apply the brake to stop them the truck will die. My suspicion is that the torque converter is locked up all the time. I have managed to get it in gear and give it gas and it'll drive and shift fine, until I come to a stop. My question, what would cause the converter to do this? It's the same transmission and converter that I pulled out a month ago and I never had any issues before...
View 4 RepliesI have a 2012 F-150 STX 4x4 with the 5.0 liter. I have noticed that when I put my truck in to reverse and sometimes drive I get a click sound. I jacked up the truck thinking it was the drive shaft that was loose but it wasn't... But I believe it is coming from the rear end. I found a video of the sound on youtube.
Check it out : 2013 F150 Rear End Click - YouTube .....
I have a 1988 FORD Ranger with the 2.9 liter engine with the four speed automatic overdrive transmission. Several days ago the transmission went out. The truck will not pull in reverse, overdrive, drive, second or first. Usually most vehicles will usually have at least the reverse, A first or second when the drive and overdrive stops working altogether. What the problem could be?
View 1 RepliesI am not the sharpest tool in the box. I was driving my 1979 f250 with a full load of fire wood going about 45mph when I shifted it from drive to reverse (I thought I was in 1st) the truck mad a loud whining sound then refused to go on. Now when I shift it in gear it feels like it wants to move and if I revved up high it will rock back and forth. A friend jacked up the rear end with the wheels off the ground the tiers spun in all gears including park and I was told they could stop the wheels by hand with the car in drive. He then took the cover off the rear end and found it to be low on fluid but no signs of damage. What I broke?
View 9 RepliesI have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 RepliesI got myself a 1997 explorer Australian model when I got it (here's the problem) if you put it in drive it will not engage but if put in first will drive normal then shift into second all good now u have push O.D then shift into drive all good (unless u slow down to almost a stop) ? New problem is, it has gone and lost reverse, put it in reverse and it engages with a small clank (normal) but just slips with any revs. I have read posts here talking about upper and lower valve body gaskets and transgo shiftkit which I have ordered but do there maybe more parts needed? Cause it's going to cost me lot just to put transmission fluid back in.
View 4 RepliesThe truck will go into reverse, but will not go into drive or any of the other gears. When shifted into one of those gears, it just idles as though in neutral. This started as I was driving down the highway at approximate 70mph. The speedometer jumped up then fell to zero as the car slowed to a stop. There was no noise except the sound of rapid fuel intake and then it went to idling. I have been told it may be a speed sensor, but I was wondering if there was anyway to confirm that before I have the truck towed down to a mechanic and find out its more than I want to pay to fix it.
View 1 RepliesI have a 97 Ranger 4x4, 4.0L, A4LD, 68k mi. with P0171 and P0174 codes, lean fuel mixture banks 1 and 2. The truck will rev up and down from 500-1000 RPM when Im rolling in Drive. When I accelerate, its fine, but when I let off the gas and roll it starts revving again causing the truck to shake. I replaced plugs and wires before the codes (1-2 months ago). After the codes came I replaced the fuel filler neck (not because of the codes), cleaned the air filter, cleaned MAF, changed fuel filter, and checked fuel pressure which was at 29psi so I replaced the fuel pump. Is there any common causes for this? Cures?
View 14 RepliesMy 2003 escape stalls from park to reverse and drive,not all the time but when warmed up. IAC motor replaced and still stalls.
View 7 Replies