Ford F-150 - 1997-2003 :: Truck Has Random Misfire Code
Aug 21, 2016
I was involved in a light accident over the weekend. I was hit in the rear by a Prius which didn't do body damage except for the 7 blade harness for my trailer towing. But, now the truck has a random misfire code. You can feel the truck jerk when you go up any grade. We changed the fuel filter and dumped in some cleaner already. One guy says its fuel and one thinks its coils. It is a 2003 F150 extended cab 5.4 with a nearly new motor. The truck has about 175xxx on it and I have had it for about 40xxx. I have not changed coils. We did check the inertia switch on the passenger side and it was not tripped.
View 2 Replies
Advertisement
I have a 03 F150 with a bi-fuel 5.4 engine an it has 195000 miles. I have had trouble for some time now with misfires. I bought the truck in october of 2011 with 125000 miles and replaced all the coils and spark plugs because it was misfiring badly will running on CNG. It was fine on gasoline and never had any codes. After I replaced the plugs and coils it ran fine on CNG and gasoline.
This summer 2013 it began missing badly at highway speeds only when running on CNG. If I accelerated the miss would go away until I was light on the throttle again.I checked the misfire count and found the bad cylinder and replaced a coil. Then a day later same thing on another cylinder. I swapped a coil from another cylinder and problem went away for a day. Eventually I chased the misfire around all the cylinders on the engine until I had ended up either replacing a spark plug or swapping a coil on all the cylinders. And I still had a misfire. It seemed to be worse on days with temperatures above 90 degrees. Eventually I got it to stop misfiring.
So now 5 months later I am back again with a misfire. This time it is misfiring on both gasoline and CNG and under any throttle conditions, except coasting. I have no codes. And the misfire monitor is sending me around the engine again. I have replaced a spark plug in two cylinders and swapped 4 coils.
I'm ready to buy all new coils, but I want to be sure that it is not a waste of money since the old ones only have 70000 miles on them.
Two days ago I had the misfire monitor saying #4 in the evening and the next day without me having done any work on it it was saying #6. Later that same day it said #7 and I still hadn't done anything other than drive the truck.
I checked the connections at the firewall on the drivers side with the three large plugs that are held in with a 10mm bolt, they looked fine, no corrosion or burnt pins. I checked the connection at the ACFM which also looks good. I will check the connection at the PCM in the next day or so.
Some other problems that may be contributing:
1. I occasionally get a U1262 code (scp fault)
2. Sometimes when I check the misfire monitor it only shows 7 cylinders, sometime 9 cylinders. I am using an Innova 3160 scanner.
3. I have either a leaking valve cover gasket or leaking head gasket, because I have oil dripping from the rear bottom corner of the passenger side cylinder head right above the exhaust pipe.
View 5 Replies
I have a 1997 F-150 2WD 4.6L V-8 that began having random misfires as I would drive. I was planning on going out today to get the new plugs and coils however when I got off work and pulled into my drive something happened when I went to leave the truck wouldn't even crank it just made a clicking noise. The battery has full power (the radio ect. still works). I am hoping that the problem is with the coils and plugs but if not ...
View 5 Replies
I have a 99 F150 4x4 with 5.4 Triton, 99xxx miles. I was towing my boat when the regulator in my alternator went bad. I drove the truck with the voltage being sporadic for about 10 miles until I could get to a parts store. While driving on the bad alternator, I started noticing a misfire. I replaced the alternator, battery and DPFE. I still have the misfire....but here is the kicker. The misfire only happens when the truck reaches operating temperature. Which, in my limited knowledge, eliminates a fouled plug, COP, bad injector and a vacuum leak. I've got no check engine light so I can't pull a code. The only thing I can think of is to clean the EGR?
View 10 Replies
I just picked up a 1999 F150 5.4 with around 19k miles on it. Truck is in mint condition, stored in a heated garage since new. Before we made the deal I checked everything out pretty well including checking all the fluids, test drive, other usual stuff and didn't notice anything out of the ordinary. However, today I went for a short ride with the windows down I noticed a random pinging noise from under the truck. At first I thought it was a few small rocks bouncing off something metal under the truck, however it continued to do it randomly for the next 5 minutes. I would say I hear a ping every 15-20 seconds randomly. Doesn't matter if it's idling or under load, happens about the same either way. Aside from this, truck starts and rungs great and no error or warning lights have kicked on.
When I got home I started the truck back up and climbed under to see what it was. I found that the noise is coming from the exhaust system, mostly heard at the catalytic convertor. It resembles the metal expanding kind of ping, but I think its actually originating at the engine and the noise is just carrying through the exhaust system. I then went back to the engine bay and could hear the same random ping, just much quieter. I don't know the condition of the fuel, but based on the low miles I haven't ruled out a bad tank of gas. Only other issue with the truck is there is a bit of rust and corrosion on the inside of the exhaust tips and up into the exhaust pipe. They are still shiny and silver on the outside, just a little rust buildup on the interior of the exhaust. Hoping it's just the last 1' or so that is rusted
View 2 Replies
Not all the time, but I've noticed it after the truck has been driven - shut off - then started again within a few min period. When truck is cold or has been sitting for an extended it starts no problem. By "delayed" I mean once I try to start the truck it takes a sec or two longer than normal before it cranks. Then when it does start it will idle very low for a sec or two then pick up and act normal.
So far I've done this to remedy it:
- new fuel filter
- new air filter
- cleaned MAF sensor
- cleaned throttle body
- seafoam thru vac hose
Only thing else I suspect is weak fuel pump but looks like it was act up all the time not just when the truck is started back to back. Truck has good power when running, I did a couple short blasts up to 80mph and everything was fine.
View 9 Replies
My 03 Chev Avalanche is giving me a P0300 code (multiple or random misfire). With no distributor or individual coil is this something I can fix myself or is it shop time?
View 6 Replies
My abs light comes on with the code above and im looking to fix it. No I don't want to buy a new abs module. Code C1185 - Car Forums and Automotive Chat the only thing i could find remotely close is from this link for a 2000 ford windstar. Need to just comfirm that there is a chance that resoldering the joints would work in fixing the problem that would be great. The light comes on and off at random. 2001 f-150 lariat 4x4.
View 2 Replies
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 Replies
My truck was jerking like it had a misfire, so I talked to a few people on here and they said it could be a bad coil on plug and some said it could be a spark plug misfiring. I put all new Motorcraft plugs and boots in and the problem of the jerking and possible misfire stopped.......until now, its back! The check engine light has never come on and this problem is getting ever so annoying.
Could it be a dirty fuel filter? Can a coil be bad and not throw a code for the check engine light to come on? Something in the EGR? The problem persist at 1000-2000 RPM's mainly.
View 5 Replies
I've got a 97 f150 4.6 that has randomly started missing over the last month. It has started to get more frequent and codes are showing a misfire on both cylinder 1 and 8. Both of these cylinders run off the same coil pack. I'm thinking its the coil? The plugs and wires, motocraft, have about 3k on them and the truck runs great otherwise. I just don't know how common a coil would cause this or if they would act intermittent like this.
View 5 Replies
I have a 2001 F-150 4x4 SC with a 4R70W. As a a couple weeks ago the transmission (or so I think) is slipping. When I take off from a red light the truck is shuttering. I also can be driving along at 55-60 mph and the truck jolts and shutters. I was reading some other threads and some guys think it could be a misfire, but since mine does it from a stand still i don't think it is. Just throwing that out there because it could be a factor, but once again I don't know.
View 10 Replies
I have got the most aggravating electrical gremlin possible. For over a year now, the truck intermittently just dies. Mostly it happens about 2-3 mins after start (every couple weeks or so), then takes a couple of key offs, then back ons to restart. But it does restart and then runs fine for a time.... 2 weeks ago I was rollin' down the road and hit a pothole, and whammo, she died, and wouldn't restart. I thought, "great it was the intertia cut-off going bad." I had it towed to the shop where they did some diagnosis and told me it threw a PO231 code.
The tech then said he was doing the diagnostic manual directed test, and swapped out the fuel pump relay, and it started right up. New relay, out the door. A few days later on the way to work about 2 - 3 minutes after start, she dies again. I hang my head, say a curse word, and key it a couple times, and it starts back up and runs fine. Presently speaking she's back at the shop, but the owner, who's a straight up dude was loath to take her back, because it was running fine at the time.... I've got to figure this thing out before I drive it off a cliff.
Truck -- 2001 7700 XLT 5.4L 88K miles
Symptoms -- Random interval engine stops with short delay to restart, 1 hard bump engine stop with no restart. PO231 code (after the hard bump no restart). Didn't check it previously (wasn't aware there were "soft" codes).
Troubleshooting to date -- 1 new fuel pump, 1 new fuel pump relay.
Only things left are the inertia cut-off switch (which apparently don't go bad that often), and the wiring itself/connections to the different components....
View 5 Replies
After/during the rain, every other time my truck loses considerable power to accelerate. It's not consistent but happens increasingly often. As I accelerate up to ~ 50km/h (also when I reverse), my engine will shake the entire truck. Past 50 it "appears" to go away. Typically this will last up to 10 mins and will disappear and run fine again. The last time it happened the check engine light came on and went away the next day. After reading online, I've heard about the "COP" connection??
2003 Ford F-150, 4.6L Triton V8 XL, 2WD
View 4 Replies
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.
View 14 Replies
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
View 8 Replies
I have a '98 F150 4X2 extended cab with a 4.2l with 233K on it. I have no problem with drivability when I drive 5 miles to work. However, a couple of weeks ago when I had to drive 15 miles to the liquor store to get what I needed (I live in a dry county) I got back into my truck, started it and drove of. It drove like crap like I lost a cylinder. Drove it back home those 15 miles, let it cool off, put my scanner on it and got a PO304 code and I think a PO174 (bank 2 lean) code. Went to the #4 cylinder and found the plug had loosened up.
Tightened it back up, cleared the codes, and went through my normal weekly routine of driving to work with no problem. Made a booze run the next weekend and the same thing happened. Limped back home and found another PO304 code. Found the plug to be tight and in good condition but changed all the plugs since they were cheap copper core and had 20K on them. The wires only have 20K on them, too. Installed platinum plugs, drove all week 5 miles to work and back just fine. Made another 15 mile run yesterday and the same crap happened all over again after I got out of the store and drove home.
View 1 Replies
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
View 14 Replies
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 Replies
My truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
View 1 Replies
I will add as many details as possible :
2000 f150 4x4 offroad package
5.4L with 131k on it
new Dorman intake manifold
new Global Automotive (Ebay) COPs
New Motorcraft spark plugs
About 1500 miles ago I started throwing a code signifying a cylinder 3 misfire. The truck would bog down real bad and then after 5-6 seconds of no power it would return to normal. I tried replacing the COP (both with new and then with one from another cylinder) and plugs but no resolution. So I talked to the local ford service manager and he said it sounded like intake manifold problems.
Replaced the intake manifold and no more codes were being thrown.
1500 miles later and today the truck started having a hesitation/shudder when I was sitting in a drive-thru. I put the truck in neutral and park and neither solved the issue. With the earlier issue, when I would put in neutral and increased rpm, the issue would resolve.
I pulled out of the drive-thru and the hesitation was consistent no matter what the rpm or speed. The truck feels almost sluggish and lacks power. The hesitation is like 2x/second. When accelerating its almost like the rpms and speed hesitate, jump, hesitate, jump.
View 12 Replies
