I have a 1997 Ford F150 4x4. I only have reverse gear, when you put into drive you have to rev up truck and then it will kick into gear & as long as you keep a little pressure on throttle it will stay in gear & shift fine if you let up on throttle it seems to go back into neutral & you have to start the the process all over. What is my problem? I have changed fluid & filter.
View 2 RepliesThe truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 RepliesAnything else that could cause reverse to go out of an automatic tranny other than the tranny being shot? I don't know of anything but any way to keep me from replacing a tranny.
View 2 RepliesI was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 RepliesI have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 Replies97 Saturn SL with a 5 speed manual transmission only has 1st and reverse. Can usually not even put the clutch in and it runs in 1st gear without stalling like a 1 gear automatic transmission. Weird
The Shifter moves normally but there is no 2 thru 5. Can put it in reverse. Drove it 3 miles to my home.
Anyway this is clutch related or some relatively cheap adjustment? The car is not worth the price of a new Xmission. Other alternative like replacing with an automatic xmission?
About a month ago I discovered one of my reverse lights was out on my 97 f150. So first thing I did was replace the bulbs then they both went out. So with my test light I checked the fuse and all sockets. All good there. Then I suspected the switch. So I bought a new switch. Nothing. Then checked the connector with the test light. Thought I found my problem there. So I bought a new connector and when I connect the wires, they only flick on once. Not even for a full second. I hear a click and I'm told the lights flick on once and that's it.
View 1 RepliesAs the title says my abs light is on. My drive way is really steep so when i pull in before i put it in park i put on my ebrake because i heard that save ware and tear on the trany. Today when i got in it to leave I released the break and put it into reverse and i had nothing it wouldn't even role backwards. so i put it back in park and then into reverse again, and again nothing. so i revede it up a little and there was a huge clunk and then i had reverse but my abs light came on.
View 9 RepliesI have 2001 F-150 2wd w/v6 and OD automatic. All of a sudden I have no reverse and while in od will not shift into od. If I turn off od it shifts fine but still have no reverse. I want my truck back!!!
View 4 RepliesI have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 RepliesIn my 1998 f150 4.6L 5 speed manual. When I go to put it in reverse I get 1st instead, but if I do a second shift to reverse I get reverse. This happens on an average of once a week.
I know this can happen in FWD cars where you put it in one gear and get a different gear instead. Something to do with the shifting cable. But the f150 is RWD, the shifting problem only happens in reverse. Is this problem someone without ASE certificates can do, or without dropping the transmission?
I'll add to this so I don't start yet another post. Ive thought of the problem and if it was really going into 1st instead of reverse the problem likely would be bad enough it would just stay in 1st. Its possible that I am getting 4th gear when I go into reverse which tells me the clutch grabs really well, and its a problem I really need to fix, I don't know that much about transmissions but I do know if it keeps getting 4th instead of reverse, the clutch wont be so good pretty fast.
So ever since I bought my f150 about three months ago it makes a whining noise from the transmission while I am reversing it. What could be the cause of this? Should I bring it in for a trans flush and filter change? What would that run me?
View 1 RepliesProblem I am having with my 2000 4.6L truck. When the outside temps fall below about 40deg F, I have to rev the engine a little (approx 2100 rpm) in order to get the transmission to shift from park into reverse. If I don't do this, it bogs the engine down and the motor dies.
Once I am in gear, everything works normally. I have no codes or lights. I have tried a new IAC valve, checked and replaced the trans fluid and filter. This is a very strange issue to be having. It SEEMS like it might have something to do with fluid flow? Like maybe the transmission cooler is plugged partially?
I have an automatic 5.4L (L code) 2000 Ford F-150 and I am having problems with the reverse lights not working when I place the transmission in reverse. Fuse #5 in the passenger compartment fuse panel is good and both reverse lamps are good as well. I have also metered the LB/PK input wire at DTR sensor and it is reading 12 volts when the ignition is in the on position. I have also the metered the BK/PK wire output wire at the DTR and this wire also reads 12 volts when I place the transmission in reverse. I have checked continuity from the BK/PK wire at DTR to the BK/PK wire at the reverse lamp socket and I do not have continuity. I then ran a fused jumper wire from the BK/PK wire directly to the BK/PK wire at the reverse lamp socket and the lamps will light up when I place the transmission in reverse and will also turn off when the transmission is placed back in park. So it seems that the DTR is not defective. I'm not sure what else to check. Obviously the BK/PK circuit is open at some point between the DTR and the reverse lamp socket, but I'm wondering if there is something else that I need to check. The vehicle is also equipped with a factory trailer tow package
View 3 RepliesThe trany is less than a year old rebuilt by a local shop.
Starting two days ago when i put the shifer in anything but reverse and 2nd it acts like it is in nurtral. 2nd and reverse are strong and do not slip. do you think its in the linkage? Or is my tranny dead?
its a 99 f250 256K auto 4x4 xl
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 RepliesI have a 2002 f150 with the 5.4 motor and a auto transmission and when I go in reverse the rear end makes a loud whining noise? The fluid level is fine. Should I add the gear oil additive to the rear end or change the rear end oil and add that? I am looking to sell the truck so what could cause this noise?
View 1 RepliesJust got a 98 f150 yesterday and I noticed last night when I went to shift into reverse, with the clutch all the way to the floor as I tried pulling the shifter back, it sounded like the clutch wasn't engaged at all. Shifting from all the other gears works just fine. Ive found that If the truck is off and I start it in reverse it works just fine.
View 3 Replies99 f150 supercab LWB 2wd 5 speed with 4wheel disc. I just replaced the rear rotors, pads, ebrake hardware and ebrake shoes. I have the shoes adjusted in as much as possible. With the e brake pedal disengaged and backing up, the e brake shoes grab the rotors and try to stop the truck from backing up.
I have lifted the rear end and pulled off the star wheel cover and turned it back as far as I can. When I rotate the tire forward by hand its fine, but when I reverse the rotation I can see the star wheel move abruptly through the hole in the backing plate as the brakes grab the rotor. What to do next?
I put the star wheel in the way the last one came out, could it be backwards, does it matter? I should tell you that currently I only have 1 side (drivers) ebrake installed because I am missing a piece for the other side that I can't buy. Will be going to a junkyard soon. This should not cause what I'm experiencing though.
2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
I have a 03 f150 2wd with the 4.6l. Recently it has been slow shifting into reverse(about 2 full seconds) and when it finally gets in reverse it shudders when it comes under load. The fluid is full and not burnt...
View 1 Replies