I need to clean my throttle body on my '97 F-150 and it has a label saying not to clean directly. Is it still safe to use TB cleaner and to go ahead and clean it? It needs done but how would I go about it.
View 6 RepliesHigh mileage 1999 4.6 4wd 5 spd: Needed to replace the rear ABS sensor and decided to clean the throttle body too while the battery was unplugged. Cleaned it around the butterfly and not much else. Truck idled at 750 BEFORE cleaning the TB. Now it fluctuates between 820 and 950 rpms. Also tends to stay at a higher rpm after pushing in the clutch and taking it out of gear.
Did a thorough check for vacuum leaks, nothing. After research, I cleaned the IAC and re installed (battery was disconnected then too). No improvement. Unplugged the IAC while running- ZERO change in idle. Installed new IAC, no change whatsoever. Unplugged NEW IAC, no change whatsoever. Is there an issue with the PCM needing time to fully re learn? Am I missing something.
read a few posts over the years relating to dirty throttle body, but never understood them. At 60000 miles, should this be attempted by the average guy or just leave it alone if it aint broke?
Any pics addressing where is it, what makes it dirty, how to open it, what to clean it with and how often as preventive maintenance?
I bought a 2009 f150 5.4 with 150000 miles on it. I have a slight hesitation from idle so I want to clean the throttle body. I found several for the older f150"s with the horizontal throttle body but this 2009 has a vertical mounted one. I change the air filter and cleaned the MAF but didn't change anything. My wife's ford 500 had this problem and cleaning the throttle body completely cured it.
View 3 RepliesI cleaned my throttle body this afternoon.
My car started fairly easily, and I continued with running it to 4k RPM a few times, then took it for a ride. I floored it a few times, as suggested, to clear everything out.
Now, my 2004 J-VIN Camry is running around 1200 RPM, it was at about 650-675 before the cleaning. Is this normal? Do I need to d/c the battery to reset the ECU so the car can re-learn with a clean TB?
I have a 2012 Camnry I4 and want to clean the throttle body.
Is this throtte the type that I can manualy open valve by hand without damage, or does the pedal need to be pushed to open, to prevent computer or throttle timing issues?
I have a 2015 F250 with a 6.2L and want to clean my throttle body. I have done several before on other vehicles but, just figured I would ask before I just jump in there. Cleaning throttle body on their 6.2L?
View 5 RepliesI decided to take out the throttle body and clean it with throttle body cleaner that I got from autozone, after I put everything back, I started my car and the motor was shaking and smoking a lot out the muffler and just would not be drivable at all. the RPM was just going up and down and hesitating bad. later I took off the spark plugs and they were very much burnt black at the tips and that is probably not normal right? but I replaced them with NGK BKR7E spark plugs and it still gave me the problem.
View 13 RepliesI have a 2004 V6 LE with about 135k miles. I cleaned the throttle body two weeks ago, just because I hadn't ever done it. It wasn't too dirty. Before the cleaning, it idled at < 1k revs. Now, when I start the engine cold, it revs at around 1500, sometimes higher. It goes back to normal after the engine warms up to operating temperature.
Also, I hear a very slight high-pitched whining (maybe hissing?) noise when I accelerate. The noise is more prominent when the engine is cold. I checked for vacuum leaks but couldn't find any.
It feels like I'm depressing the gas pedal a little bit when I have it in drive or reverse, and it wants to pull harder than usual. When I bring the car to a stop with light brake pressure, as it drops into first gear, the car gives a slight tug forward, again, as if the gas pedal is depressed. I mention this to show that it's not just an issue with the rpm at startup.
I suspect that the issue lies with the throttle position sensor, which I may have jostled when I moved the throttle valve. The method I used when cleaning was, I first tried opening the valve by hand with the ignition off, but the resistance was much higher than I had anticipated. So I did the key-in method by turning the ignition to ON and putting a brick on the gas pedal. There was a high-pitched whine coming from somewhere in the engine bay when the key was ON, which I had not noticed before; I wonder if that is normal.
This seems to be a rather common issue after cleaning the throttle body cleaning, but there doesn't seem to be any consensus solution besides to wait it out.
2002 Camry XLE.
I cleaned my throttle body today. Since the throttle plate moves by a motor, in order to keep it open, I turned the key to ON and held the gas pedal down by using some weight.
After I put everything back, the idle was high 2000+, then stays at 1300 to 1400 range. I drove about 10 miles and it is still the same. When stopped at a light in drive, the idle is still 1000
Did I mess up the e-throttle or the throttle position sensor? (Since I used a weight to hold the gas pedal down, I am worried now).
2002 V6 Camry 145,000 miles, cleaned throttle body with TBC fluid, now starts runs for a few seconds and dies. In order to open the butterfly in cleaning I turned ign on and propped pedal down. After cleaning the car ran better but idle was high and a little erratic. I disconnected the neg batt for several hours, now it starts, but dies right away. In the cleaning process I had removed the throttle control sensor an reinstalled it. Can't keep it running long enough to adjust it.
View 8 RepliesI cleaned my daughters throttle body on her 2005 prius. Sprayed it down on the vehicle trying to fix my P0505 code and now its idling high. Is there a learn procedure to reset this after service.
View 6 RepliesCar is 2000 Corolla with 60k miles that sometimes has a low idle (sometimes) when driven for the first 15 minutes early morning. Especially when accessories turn on, the RPM drop suddenly to 600 and recovers to 623 then back to 650rpm. After 15 minutes, everything works fine (normal 650 rpm)....my guess is the IAC Valve/throttle body needs cleaning.
What exactly do I need to tell me mechanic? That both the IAC Valve and throttle body needs to be clean? Also, after "cleaning it using a spray"....should he wait till the "spray dissipates"? What happens if it goes inside the engine?
Got told by the dealer I need to replace my Mass Air Flow Sensor...to the tune of $657 dollars. And get a throttle body cleaning.
View 14 RepliesI cleaned the throttle body with CRC throttle body cleaner and now the motor idles at 1000-1300 rpm. Is this normal for a newly cleaned throttle body? How can I bring down the idling rpm?
View 4 RepliesThe Throttle Body on my 2001, 4.6 L is making a strange whirring noise, when you puy your hand on the intake pipe, you can feel a slight vibration. The Truck idles and runs okay, with no codes. Giving it a little gas and the noise goes away. The last thing I did was clean the IAC with Gum Out Carb cleaner, the second or third time I've done this over many years, with no problems. I'm a little perplexed at the cause.
View 6 RepliesI'm usually over in the EX forum but today was working on my brothers 1998 F150 - V8 4.6L. Had the EGR code P0401 and due to FTE I found the problem took the throttle body off and found it was definitely plugged. One of the bolts was really loose and came off way to easily. Didn't realize until cleaning why... Now I drilled 8 studs out of my aluminum EX heads but this one has me pondering how I'm going to clamp this thing down and center a bit..
1st pic - ports WOW - guessing this was the problem ...
2nd pic - bigger issue ...
3rd pic - the ports cleaned up ...
I have a throttle body noise that sounds like a warble,It is sporadic and I think it should not be their. But I have heard some other f-150s make the same noise. Is it normal or is something not right.
View 3 RepliesI went to clean my wife's throttle body out with brake cleaner and I think I sprayed too much into the throttle body now the car won't start. It makes a small clicking/grinding noise when I try to start it. What have I done?
View 12 RepliesFew weeks ago.....Prius was showing the P0505 code .... Mechanic, ran diagnostics and determined it was dirty TB. Cleaned TB.....cleared the code (inspected PCV...hoses).
When I initially picked it up it was revving very high....so he hooked it back up to the scanner and did some type of "reset" for the idle (this cleared most some computer settings...back-up beep, radio stations, etc...). Everything ran fine for past 3 weeks...
Just last night..... started running rough again. What I noticed this morning ... Started it up and it ran very rough til the auto shutdown after warmup (no warning lights). Then....when I started driving slowly out of the lot...it ran "rough upon acceleration"...... Then fine at cruising speed. Same behavior at every light....rough acceleration.... fine once up to speed. Just started it up again and same behavior.....(does not die...just very rough).
I busted the cable end by not removing it properly. My question is what is the proper method of remove the cable from the throttle body? Are the cable ends replaceable? If so who has them as a google search didn't find any? I've tried to find written information but haven't any luck. bl2009
View 1 Replies