Ford F-150 - 1997-2003 :: Sticking Front Brake Calipers
Sep 17, 2013
I have a 99 150 4 wheel drive..5.4 ..auto...110.000 mile.....notice when driving in town in hot weather....when you are on and off the brake petal a lot....stop and go..etc.....the truck starts to hop or bounce....some....I got out ..and notice the right or passenger side front brake seems a lot hotter than the drivers side......but ...when it does that....the steering wheel doesn't pull to one side...when changing pads before ..notice no one side worse for ware than other...thinking it must be sticking brake calipers....they don't do this say on interstate driving even when on and off the petal some...
View 1 Replies
Advertisement
I have a '99 Volvo XC V70 with turbo. The right rear and right front calipers are sticking.
View 6 Replies
I just bought a 1998 F150 2wd with the 4.6L(no ABS) to be my beater home depot truck. The brakes barely functioned, so I replaced the front bearings, rotors, pads, and calipers. I bled the brakes exactly like I normally do. When I tried to move the truck, the rear tires spun with the front completely locked(also discovered the right rear line had a hole and crimped the line for a moment, but it was the tire that was spinning).
I searched and many people said that bad rubber lines cause the calipers to lockup. I loosened the bleed valves and the fronts were still locked(jacked up the truck and used a breaker bar on lug nuts trying to rotate each tire). I am guessing that it has to be master cylinder or the steel lines. Any tests I could do to narrow down this issue further?
View 1 Replies
I have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 Replies
Just took a drive to Home Depot, hopped out of the excursion and got a whiff of burning brakes. I'm thinking i have a stuck caliper on the rear driver side just enough to cause the smell but not enough to slow acceleration or speed up deceleration. Should I just grease up the calipers?
View 14 Replies
I have a 2001 mustang GT. I have 2 front calipers that are sticking. I changed both calipers twice, new brake hoses, bled all the wheels and the master cylinder. Why the calipers won't release?
View 19 Replies
I have a 2001 ex. 4x4 6.8 v10. I have been having vacuum issues and brake issues lately. My front brakes seem to be sticking, some times they drag some times the don't squeeze when I step on the brake causing uneven wear and pulling when I stop. Also feels like I have no power assist. I also have a vacuum issue with the auto setting on the hubs, they don't engage I have to manually lock them and sometimes my a/c stays on defrost. And my cruise control doesn't work, the light comes on and love done the self check but it doesn't show anything is wrong. Could I have a bad brake booster?
View 5 Replies
Ok so I think I have sticking calipers on the rear passenger side of my truck, not 100% sure but ill be getting under the truck tomorrow to check. My question is how hard is it to fix this and how long do you think it will take? I have all the right stuff to get the truck jacked up and I have enough money to do this, time is just the issue. It gets dark around 4:30-5:00pm here and I get home from school at 3pm, and have work also but not until saturday this week.
I'd prefer to do this after school if possible because I've stopped driving it so that way I don't wear down my brake rotors and pads for no good reason. I have to drive the work truck that has many of its own issues but its driveable, headlights are very dim due to oxidization and is dangerous to drive in the snow due to the tires (no money to replace right now). How hard and how long this would be? What else it could be shoot! The problem is, it slows down if i let off the gas as if i was breaking, high heat from rear passenger side brakes/burning rubber smell.
View 14 Replies
Since I have this car i noticed that the brake calipers (especially the front) are very noisy. This problem is caused by caliper's floating guides that become loose and the entire brake caliper shakes. I asked at a kia mechanic who answered to me to change the calipers support. For my trusted mechanic is useless because, according to him, this type of support have this problem (he tell me that also others car have this problem like older nissan micra) and sooner or later would return noisy.
Some time ago with greasing the floating guides i temporary solved but drying up over time the problem come back.
View 6 Replies
Fairly recently acquired 1992 525i, 101,000 miles. Love the car and driving feel, don't mind putting the effort in but do not know where to start. She needed some work including both upper and lower control arm bushings. Replaced those over the last couple of weekends. This week the front brake calipers are locking up adding significant drag to the car, overheating the front brakes, smells and feels hot. Rear brakes appear to be fine. Seller had replaced brakes within the last 5,000 miles. I thought maybe he did not 'grease' the caliper guide pins and components, so I tried that and all was well for a few miles then back to the same locking brake calipers.
Is this brake caliper, brake cylinder, master cylinder or ABS related? Do I need to bleed the system? I cannot not imagine how but could replacing any of the front suspension components have had anything to do with this? I read on one thread about an interconnection (power assist) provided by the power steering pump and that 'over filling' the PS reservoir could cause such a problem. I did add fluid to the reservoir recently but the level is between the marks on the cap dip stick.
If caliper, or cylinder related is this DYI? How about the ABS? I have been looking for some good links to address this problem and repair procedures but no luck as yet.
View 9 Replies
I've replaced the front brakes twice now on my 2004 2.4L Manual Santa Fe.
Each time the dealership has commented on some excessive rusting of the calipers, and this last time around one had actually seized and they had to cut it off.
When I got brand new ones put on I noticed they were nice an shiny silver. Within 3 weeks there were full rusted...and still are. I don't get it??
2004 Santa Fe .... Is it possible something is dripping from somewhere that is caused this premature rusting?
View 2 Replies
Tons of information on this and its possible. What? I'm still learning the search feature.
View 1 Replies
Yesterday, I noticed that my right front brake caliper seemed to be sticking. This morning I jacked up the front end, and could barely turn the right front wheel when it was off the ground. So, I have concluded that that caliper is sticking. So, here is the question(s): what is the best way to repair this (new caliper, rebuilt caliper, or rebuild it myself), do I need to do both sides the same or can I just do the one that is acting up, and should I expect to pay. I have some mechanical ability, but that Haynes manual doesn't make too much sense to me. Getting it professionally repaired is extremely inconvenient, I need to be back at school (300 miles away) Tuesday evening, and probably couldn't get it in to get it done before then.
View 12 Replies
Heard clunk (technicdal term) noise when you are in reverse and press the brake pedal. It is coming from the front end/brake area. I did not see a service bulletin for this.
View 10 Replies
I have A 97 F-150 4X4 with rear drums. I noticed the brakes felt like they weren't releasing right away after i let of the brake pedal. i took drums off and noticed on the left rear the front shoe moved normal but the rear shoe didn't move at all. on the right side front shoe moves normal rear shoe very very slow, and i could see rear shoe was worn way more than front. So I replaced on both rear the shoes, all the hardware, springs, wheel cylinders and brake line from cylinders to the proportioning valve.bleed the brakes, and adjusted the drag on the drums. Now i drive it, test it out, feels like the same issue is going on. feels like im driving with the brake on, and right rear gets really hot. Did i miss something? not do something right?
View 4 Replies
2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
View 5 Replies
I know this has been talked about many times and how to solve the issue but thought I would ask some other questions too. Earlier in the summer, I did grease the slider pins as preventative maintenance. I don't drive my truck all that much and when I used it yesterday, (about 30 minute drive) I came home to burning brake smell. I'm wondering if enough heat would cause the caliper to go bad? Should I just grease the pins again or change out some parts?
View 6 Replies
My buddy has been having a strange problem with his 275,000 mile 2003 F150 2wd. The right side caliper will lock up out of the blue and will not release for anything. We put 3 news calipers on it within a 4 week period thinking that we had a defective one but no change. I am thinking either a bad brake line or, more likely, the front abs block...
View 1 Replies
I know on some cars and trucks you need a special tools to push the caliper back in. i just use a large c clamp to do the job. Question do i need any special tools to replace the front brakes pads?
View 7 Replies
My 97 F150 4.6 4x2. I have a semi-rough front end "chatter" when the brakes are first applied after vehicle has been sitting overnight. It feels like it comes from the front disk brakes, I assumed it was a warped rotor or loose wheel bearing so I replaced the front rotors (old were to thin to turn), new wheel bearings and pads. Still had the issue, so I then assumed it was a bad caliper... replaced both those, and all related hardware. Still have the issue!
I can not reproduce the event until the vehicle is in the cold state and it will only do it once or twice, so I am finding it difficult to diagnose. Tired of blindly attacking this issue by changing what I thought was obvious. F150, 130K miles, 4.6l, automatic, 4x2, rear drums, front disk
View 2 Replies
I have a 2001 f-150 the brakes are sticking and I get a bad shake which seems to come from the front and rear of the vehicle. It doesn't do it all the time but when it does it slowly gets worse. I have replaced 3 of the 4 calipers and will be replacing the forth, but not much is changing.
View 9 Replies
