i just purchased an '01 expedition with the 5.4. I was told #5 spark plug blew out. Upon examination, it appears to be #6, second from the front driver side. Anyway, as I was looking, it just didn't look right. There was a spark plug socket stuck in the well, with the plug still in place. How to get the socket out? I can get an extension on it and it will turn, but it's tight. But I can't pull the socket out.
View 9 RepliesHave a 2005 F350 4x4 SRW 5.4L with roughly 90k miles and I am replacing the original plugs. Broke three out of seven which was expected and have them replaced. You probably noticed I wrote 7 plugs above. The 8th plug which happens to be the #8 plug is giving me fits. I can't get a socket on it. The socket spins smoothly by hand with no ratchet over the plug but no upward movement. I cleaned the base of the hole thinking it might have some debris preventing it from hitting bottom. From what I can see after cleaning and blowing it out, the base of the hole is clean and there plug appears to have something for the socket grab onto. Out of curiosity, I have tried smaller and larger sockets in both 6 and 12 point with no luck. Is it possible the plug was set too deep in the head from the factory?
View 13 RepliesI'm trying to replace the spark plugs of my 2006 Prius, but the deep well 5/8 socket attached to a 2 in extender just turns loose, as if it does not fit in the top of the spark plug. I tried also 3/4 and 13/16 but those don't even fit in the spark plug well. I tried in another spark plug to the same result. Problem to replace to spark plugs?
View 7 RepliesI have a 1997 F150 4.6 V8 and as we all know these trucks are notorious for the spark plug blowing out. Although when I bought it I never had an issue until we put motorcraft plugs in. After a couple weeks of having these plugs in the porcelain blew out of the plug with the threads still in the head. The spark plug screws into a threaded insert which then screws into the head. We replaced the plug and nearly a month later the porcelain blew again. Replaced it, same story a week and a half later. Before the motorcraft plugs I had autolites in it, and I never had the slightest spark plug blowout problem. Should I just put an autolite in the cylinder that's blowing them?
View 4 RepliesI had a plug blowout last Thursday on the freeway. I wasn't sure of what happened with my truck, it was a shutgun going off. I had to towed to my local Firestone.
My truck is a F-150 4.6 2003 with 206,000 miles.
The short of the story, plug #3 blowout. It trashed the coil and I needed a new plug. They used a Helicoli and I have been reading that they shouldn't have used a Helicoli. They should have used a Time-set.
What's wrong with the Helicoli's? Is this fixed going to last for awhile? They said the helicoli worked well. The truck had 7 NGKs and 1 motorcraft. It has all new motorcrafts now.
1997 f-150, 4.6, 147K miles. This morning I started the truck and the engine light was on. Felt a miss in the engine. Drove 1 mile and back then checked the wires. Found one not firing. Traced it back to the plug. When I pulled the plug boot off I noticed water in the recess, surrounding the plug. Once I blow out the water, I'll checjk the plug but I would like to know if this is a natural occurrence. I thought the boot would prevent water from filling the recess and sitting there. Or does the water just evaporate when the engine gets hot?
View 14 RepliesOkay so I was getting the misfire in cylinder 3 so I pulled the plug out and it had coolant in it. Does that mean it needs a new intake manifold gasket? That is what the guy told me at the parts store. Also can I drive it like this or will it damage the engine?
View 1 RepliesI have an 01 f150 with 5.4 triton. This has been great truck, never really had to do anything to it. It has 195k on it. Week or so ago it started running rough. So I replace the plugs and coils. I noticed some of the plug wells had oil in them. Got done and the truck is running like new.
Not sure where the oil is coming from. Not the piston as the plug was dry on the tip and truck not smoking any. I has began using a quart or so between oil changes. I have always changed it every 3k. Is it just time for new motor. Like I said it is running like new.
I was checking my COPs and the first one I pulled out of my 2002 f150 5.4l had a clearish liquid on the coil boot. I looked down in the spark plug hole and it was filled almost to the top of the spark plug itself. I smelled it and it smelled like gas. Why this would happen and what should be done to fix it?
View 3 RepliesI found a leak today on my 2001 Ford F150 Super Crew, 5.4 engine. In the picture, it was leaking to the right of the spark plug, behind the hose. It was bubbling up from the metal. It hasn't been overheating except when I got home and idled with the AC on. What I'm facing?
View 12 RepliesMy son has a 2001 F150 with a 4.6L V8 that's blown a sparkplug from # 3 cylinder. The plug looks as if struck by lightning and has a burn groove as deep as a kitchen match stem the full length of the threads.
How difficult is an engine swap/change using another 4.6L? Neither of us have extensive mechanical backgrounds but plenty of aptitude.
This a 02 with 5.4, had codes po306, pulled and checked sparkplug had moisture in it. Fixed that ran ok for a little bit then started again, no codes now and smells a little like rotten egg.
View 1 RepliesLast weekend my number 4 spark plug blew out while on the highway. The truck stayed on long enough for me to get off the highway and pull over before it died. I towed the truck home. Last night I repaired it with a helicoil and replace the spark plug and coil. Now the truck cranks but won't start. I noticed that my theft light flashes fast and doesn't stop after a few seconds or during cranking. I still haven't tested relays or fuses because it was late after the repair. I will be checking those tonight.
I will be reading and taking suggestions and posting my results tonight while I'm working on the truck. I will be checking the fuel pump and PCM relay tonight. I will also try 2 different keys and checking the Inertia switch on the fuel pump to see if that tripped. The truck is a 2001 F-150 Lariat Supercrew with 150k miles on it. 5.4 liter engine.
With the many discussions on F150 spark plug blow outs, is there any consistency in which Cylinders usually go or is it completely random. In my 2003 F150, 4.6, 2wd, I've replaced #3 cylinder with insert and now #2. Currently I'm at 154,000 miles but want to travel cross country with a load. I don't want to stall out on the hwy, would it be wise to go and insert the remaining cylinders - not cheap. My mechanic is willing to inspect with a bore scope the threads and re-torque. Is there a point at which if it hasn't been a problem it won't be. Truck is used primarily for commuting and to pull a single jet ski in the summer. Both blow-outs happened at a stop-light about 20,000 miles apart with no load.
Follow-up. Did inspection, found cylinder #7 nearly stripped out - it was actually pushing up the coil. Funny thing is, this plug had already the small insert which was coming out with the plug. I bought the vehicle new. Was this a factory repair? or did my previous mechanic strip-it when replacing all my plugs at 95,000 miles? Lucking the large inserts my current mechanic uses was able to find some metal and make a good repair. Looking at the cylinder order, I have now replaced 3 of the inter four cylinders (2,3,7) should have I done #6 too, this is probably the next high risk cylinder or not?
Today I began to change the plugs on my '04 Camry 4cyl for the first time at a little over 100 thousand miles. The first plug I came to doesn't want to come loose. I started with a 8" ratchet, now I'm on it with a 12 " ratchet and it doesn't budge. I'm able to go up to 3' and almost anything in between with a breaker bar plus a cheater, but I've heard terrible tales of people who break off a plug. How much force can you safely put on a plug? how do shops remove stuck plugs?
View 14 RepliesHad the #2 ignition coil go bad (for the second time, mileage is only 84K) and decided to proactively replace all the spark plugs at the same time. #2 coil came out fine and replaced the plug with a toyota irridium. However, the #4 and #6 coils each separated from their respective boots. I was unable to extract either boot. I was able to re-insert the coils without replacing the spark plugs and the engine is running fine (no codes). Before I take on #1 , 3, and 5, I'd like to extract the stuck boots in #4 and 6 and replace the plugs.
View 3 RepliesWant to replace the rotors on my '97 2wd truck. What size socket do I need for the spindle nut? Can't seem to find that information with a search. I popped off the dust cap and test fitted a couple of sockets after removing the cotter pin and cap that locks the nut in place. 1" too small, 1-1/16" a little loose, so I'm thinking this nut is metric and I want a 26mm socket?
View 3 Repliesis there a diffrent spark plug socket too take out the plugs on the 5.4 3v motor cause i tried a socket i thought would work but i wouldn't go in the spark plug hole like what gives
View 4 RepliesThe spark plug in chamber 2 blew off while the vehicle was in motion (approx 35 mph). Purchased replacement plugs and when I went to install, there was nothing for the plug to grab (i.e. appears that all of the threads on the block/casing are gone . Not sure what my options are.
View 2 RepliesI took a long trip this last weekend and before the return trip I checked the oil and realized I need some. I put two quarts which brought the level just about even with the top mark on the dipstick. the return trip was fine. Next morning I started the car and right away notice that the engine was misfiring. I checked the spark plugs and noticed that one of them was loose and had some oil in it. I checked the oil and now it showed the level to be well above the top mark on the dipstick. Could too much oil cause the spark plug to get dirty, get loose and misfire? This car is a 1997 and has 206,000 miles. This is the first time this has happened. Could the same thing happend with a 1999 Honda Civic?
View 10 RepliesI have an 03 F250 5.4L
Driving down the highway today, I notice my truck was jerking forward a little, hard to notice almost felt like I was hitting very small pot holes. I revved up a little to see if I could notice any noises and I got a loud pop. after the pop, got a noise like an exhaust leak so I pulled off to the side of the highway and popped the hood (engine still running). Noticed the noise coming from the passenger side most forward spark plug. Then noticed the part that the coil attaches too had broke off from its bracket and was unseated, shut off the engine and pulled it out to find the coil cover had melted to the coil.
The spark plug inside was moving freely so I took it out thinking it stripped from the header. Come to find that the plug had actually separated from its threading completely so just the core part of the plug had shot out from the cylinder, the threading and socket attachment portion still fully attached. I installed a new spark plug and new coil harness and coil. Seems to be running as good as new now. Is there more to this than a simple blown plug that I need to worry about?