I have a 03 f150 2wd with the 4.6l. Recently it has been slow shifting into reverse(about 2 full seconds) and when it finally gets in reverse it shudders when it comes under load. The fluid is full and not burnt...
View 1 Replies I had recently purchased a 2003 golf gti AUTOMATIC (with optional shifter) with a 1.8 turbo 4 cylinder engine. The vehicle has 139,000 miles on it. Before purchasing, I had a mechanic come out and look at the vehicle for a pre-purchase inspection, and ran the code P0303 (cylinder 3 misfire) which without test driving, told me that is what caused the shift shudder I noticed when I had test driven it a previous day. He told me the coil packs were in good condition by looking at the top of them, and told me if I replace the spark plugs, the issue should go away.
I feel it is important to mention that he had also run codes on the transmission and nothing came up. Taking it home, this morning I had replaced the spark plugs and driven it for about an hour both regularly and aggressively to test it. The problem is still there, and I was really hoping that there is a solution to this problem, because everything else on the car is beautiful, while being my dream car, I just want it to work as well as I know it can. To be more descriptive, when shifting to 3rd the whole car feels basically like it is tripping over itself before successfully shifting.
In my 1998 f150 4.6L 5 speed manual. When I go to put it in reverse I get 1st instead, but if I do a second shift to reverse I get reverse. This happens on an average of once a week.
I know this can happen in FWD cars where you put it in one gear and get a different gear instead. Something to do with the shifting cable. But the f150 is RWD, the shifting problem only happens in reverse. Is this problem someone without ASE certificates can do, or without dropping the transmission?
I'll add to this so I don't start yet another post. Ive thought of the problem and if it was really going into 1st instead of reverse the problem likely would be bad enough it would just stay in 1st. Its possible that I am getting 4th gear when I go into reverse which tells me the clutch grabs really well, and its a problem I really need to fix, I don't know that much about transmissions but I do know if it keeps getting 4th instead of reverse, the clutch wont be so good pretty fast.
Just got a 98 f150 yesterday and I noticed last night when I went to shift into reverse, with the clutch all the way to the floor as I tried pulling the shifter back, it sounded like the clutch wasn't engaged at all. Shifting from all the other gears works just fine. Ive found that If the truck is off and I start it in reverse it works just fine.
View 3 Replies2003 Explorer tranny. 4.0 V6, 213km (133 miles)... Biggest concern is 4-5 upshift shudder, no rpm rise, just a shudder and slow shift. Slight shudder on 3-4 too, I think. Some online reading points to torque converter failure.
Other symptoms: sometimes slams into gear when shifting out of park, other times it feels like there is no fluid in converter when first put into gear, especially after sitting a day or 2. (my truck does the same thing, but that's after sitting 2-3 weeks at a time)...
2000 F150 Lariat, XC, 2WD, 5.4L, 4R70W
I don't know if this all started right after I got back from towing a 3500# lathe + 2000# trailer back from Texas a couple weeks ago or if there might have been some slight symptoms before. I do know that this really got bad a couple days ago and I haven't driven the truck since then.
So, here's what is happening. I noticed a few days before that when I would back out of a parking space, the truck didn't seem to go right into reverse. It was as if it was in neutral, but as I was reaching to jiggle the gearshift lever, it would engage and I could back out just fine. All forward gears, and shifting, have been fine all along, including lockup. I kind of wondered if the shift linkage had somehow moved and was on the edge of being in the right spot, so I was going to have a look at it one evening soon. Then a couple days ago, I went to back out of a parking spot at work and it wouldn't go anywhere.
Just acted like it was in neutral. Put it in drive and it engaged just fine, then back to reverse and nothing for a few moments before it finally engaged. Then, as I was backing up, it acted like you might expect a limited slip that was not slipping to behave. But, that was right before I put it in drive and went home. After I got home, I tried it out some more and found that in reverse, it just wouldn't go anywhere unless the truck rolled a little bit. I don't know if the rolling really had anything to do with it or not, but the driveway is on a slight incline, so it happened, and then the transmission would engage. But, when it did start to back up, even straight, at first it acted like it was under a load, then when it started to move, it bucked really badly. Put it back in drive and all seems fine.
There are no codes set. Trans fluid is full, and doesn't smell or look bad. I've searched for reverse shudder, and other stuff, and there are threads about the TC, about no reverse at all, and a bunch of other stuff, but nothing like this that I found.
I have an 01 4x4 Ext cab with the 5.4 auto. It just started to shudder in drive doing about 20-35 mph, it quit when I turned the OD off and has not come back yet. It also jumps in and out of OD while running highway speeds, kind of like hitting a bump or something like it. The shudder was in about 10 degree temps and not fully warmed up and the jump happens whenever I am at speeds around 60-75.
View 7 RepliesMy trucks been doing something weird. When accelerating around 45-55 mph, a couple seconds after it shifts to 3rd, it does a weird type off shake/shudder. Feels like I hit a small bump in the road. Also when coming out of a cruise to accelerate, it will Make a very violent clunk and then speed up. I'm thinking it's a problem with my torque converter but my mechanic says transmission and my buddy says rear end lol. I dropped the pan and there was some shavings but nothing huge and it was the first time it was ever dropped. After 90k miles.
View 14 RepliesWhen I first bought my 2001 f150 a few mos ago there were no problems but I did notice once in a while it would give one little shudder when id accelerate. now all the sudden it shudders after around 20 mph all the way up to whatever the speed limit is. Then it smooths right out until I have to accelerate again. if I punch the gas and kick it down it will clear up but then it feels more like a surging going on.
I had the cruise set at 70 the other day and I had to slow down to merge to around 50 and when I hit resume it really started shaking bad and the service engine soon light flashed on and off for a few minutes then went off and hasn't came back on again. I took it to advance auto and no codes showed up. they said its probably the torque converter but after reading multiple forums I am not so sure now.
I have a 1999 F-150, 4.2L V6 with 206,000 miles that recently developed a rear-end shudder/vibration. According to my door jam axle code (27) and the axle tag (3 37), I have what appears to be a conventional rear differential, even though most of my research would indicate this rear-end is for the F-250. In any case, and based on other online research, I changed the differential oil with a 75W-140 synthetic and added 4oz of a friction modifier. Now the vibration appears to be worse. It primarily vibrates when taking off from a stop, whether turning or not.
I have felt the vibration at speeds up to 60mph, but it is more noticeable at lower speeds. The vibration also seems to diminish after driving the truck for longer periods of time, particularly if at highway speeds. In other words, when I drive to and from work, which is about 30 minutes each way of mostly highway, the vibration is barely noticeable once I exit the highway and slow back down to 35-40mph. When feeling the vibration, if I decelerate, the vibration immediately ceases, but starts again when I accelerate. It's not as noticeable if I accelerate harder, but I generally don't do that. The gears inside the differential didn't have any noticeable wear, chips or slop/play. What may be plaguing my usual trouble-free F150?
Just bought a 1998 5.4l F-150 Lariat. 136,000 miles.
Question about the overdrive button on trans handle. When I push the button, I don't see any light turn on (or off) and I don't feel any change in the gear ratio or increase/decrease in rpm's. I assume since the button in there marked "overdrive" that the vehicle in fact was equipped with it. Could it be a bad button, fuse, or ?
Also, it just started the shudder/hesitation at certain speeds that I see a lot on these threads. Seems like that is a coil issue as the description in many threads is exactly what I am experiencing to incl the rotten egg/fuel odor. However, it started the same day (not same time, later same day) I decided to push the overdrive button while checking out all the things on the truck.
A friend from work is having what he says is piston slap, but only under a load. I feel it could be the timing set since it's never been changed and at least 160k miles. Odometer quit working at least 5 years ago. Other than that, motor runs great. 1997 F150 4.6....
View 4 Replies99 F150, 4x4, 5.4L, 4R70W trans.
I am experiencing a shudder at speeds between 45 and 50 when trying to accelerate mildly - it usually occurs after slowing down from a higher speed.
It is similar to the bucking that occurs when you do not downshift a manual trans.
I am guessing that it is the torque convert clutch staying locked or the tranny staying in OD too long. The shudder will go away if I give the truck enough throttle to downshift or simply push the overdrive off button - which forces it to downshift to drive.
What is the probable cause?
I have a 02' f150 v6 67,000 miles. When I come to a stop, the trans shudders abit like the converter is still locked up. It then goes to stall in a few seconds. this does not happen all the time, fluid is clean. I understand there is a simple fix for this, or is this normal?
View 1 RepliesIt has been since the 80's that I have attempted to do any work on a vehicle. How do I find a vacuum leak and where is my vacuum canister. I am assuming that it is a vacuum leak for anytime my engine has a load on it the air stops coming out of the dash vents and goes to the defrost vents. I have an 2000 F150 with the large engine with about 112,000 miles.
View 11 Replies1999 4.6 (106K miles) will stumble / miss when at 35-50 mph under a mid throttle load (just before reaching the downshift point). Has been doing this since I bought the truck at 70K miles.
Computer has no codes, engine runs fine under all other circumstances, and gets a decent ~20 MPG on the highway.
Done the standard tune up items (plugs / motocraft) and cleaned MAF, replaced TPS, tranny flush/ filter. Replaced the left O2 sensor 2 months ago, but it dumped a code and was really noticeable when it went out.
I am about ready to dive off and replace the MAF, but at $100 a shot would like other alternatives to try first. I am really convinced the engine is leaning out and misfiring under this load.
I have 2001 F-150 with 4.6L. Truck runs fine until under load and runs fine until I slow down to a stop sign. Once truck sits for a few moments it fires up again and will run for a short while then will do it again. Each time i let it sit for a few minutes, it will start again.
I pull a small travel trailer and seems to happen more frequently when pulling or climbing hill, but not under full power, just when slowing down. Could this be cause of catalytic converters? MAF sensor, or fuel starving.
Check engine light is on, will codes identify if it is a plugged cat?
My 4.2 liter F150 suddenly started missing under load. A little background: It is a late 2003 and has 75k miles. It has been in my family since new, and I have had it for the last 4 years. This truck is as stock as they come, and has been well maintained.
On my way to work yesterday, it began missing. Not bad at first, but got worse. It misses while under load and under acceleration. The "check engine light" never came on. I have not put fuel in in several days, and it ran fine until now, so I doubt it is bad fuel. I started the engine after dark and looked for arcing. None visible, and I even sprayed the wires with a mist of water. I pulled the plugs and they all look normal. The gaps were all way too large, so I regapped the plugs to .054". I pulled the coil pack and it checks within range with my VOM. Can the coil pack be the problem even though it checks out on the bench? Can the large plug gaps have contributed to a coil pack failure?
Where to start. I HATE just throwing parts at this thing, and I don't like wasting money... If I let one of the auto parts stores run a scan, will it show a code even though I have no check engine light? I used to think of myself as a pretty good diagnostician, but then again, when I used to spend a lot of time under the hood, those cars had points, condensers and carburetors...
My daughter has a 2010 F150 with 5.4, when pulling her horse trailer or extended idling her truck starts running rough, so far her husband has changed the fuel pump and 2 coil packs, no luck.
View 3 RepliesGot a shudder noise similar to an exhaust leak on my Excursion V10. I have no codes ... engine idles and revs fine.. Only hear noise when under load. Goes away when you let off the gas.
View 8 RepliesLately I've had some issues with the indicator(the orange needle telling you what gear you're in). Often when I start my car, it would let me shift gears but the indicator would not move. I've never once had a problem shifting into whichever gear I want(knock on wood). Usually when this happened I would bring the gear selector back to park then try shifting it again. This would fix the issue and it would bring the indicator with it, but I knew I had to do something about it eventually.
Last night when I was on my way home, I started my car and shifted into reverse to back out. It didn't move the indicator, and nothing I could do(no back to park then trying again) would work. I eventually decided I'd just count gears to get home, then I'd have it looked at.
At home I decided to do some research as to find out the issue, and I thought I'd found it. I removed the panel under the steering wheel to look at the thumb-adjustment. Many posts I read said it's likely broken and I may need a new one (Or to fix it with zip-ties or glue). When I found it though it had not been broken. The white housing and the black wheel were both working fine, the wire doesn't seem cut. However when I put the parking brake on so I can shift gears and see what it's doing, the gear selector moves but the wire just acquires slack in it. It's still attached and I can't see a break in it anywhere, however it may be broken inside the jacket. I tried turning the black thumb-adjusting wheel both ways and got no success from that. It moved a little once but that was it.
The indicator needs to be replaced?