Ford F-150 - 1997-2003 :: Short In Steering Column - Ignition Switch Replacement?
Oct 14, 2014
I have a 1997 F150 that I have taken to a mechanic twice and it is still not right. I had a igination switch replaced and now when the humidity is really high
(I am Guessing), I can have the key in the house and my truck lights flash the radio is on and it sounds like it is trying to start. How hard is it to replace the igination switch myself. I believe it has a short someone in the steering column.
View 1 Replies
Advertisement
Recently noticed when driving, I'll hear and feel a slight clicking noise coming from my steering column. I can be going straight or turning. it is intermittent. I've look underneath and nothing seems obvious. when the truck is in park, I've tried to manhandle the steering wheel, the steering wheel is solid. the truck is a 1998 f150xl v6.
View 1 Replies
I just recently picked up a 2001 F-150 4x4 super crew. The steering column is wobbling a little when I hit bumps. I accessed the column and there are two white plastic "bushings" that hold the casted portion of the column tight against the studs with the star ends. This is above where the reinforcement bracket is bolted on. One of them is worn and won't tighten down to hold the column tight. What these are called so I can't find them to order them, I used a large washer for the time being but would really like to replace with new ones.
View 1 Replies
I'm having a problem with my ignition switch. It won't turn and I have to turn the steering wheel for it to finally work.
View 4 Replies
I am needing to replace the selector switch for my 4x4 on my 2003 F150 Lariat FX4... I already have the new switch. Whats the best way to get in there to remove and replace the switch?
View 7 Replies
Started truck and turned the wheel far to the right and shut the truck off to get better access to the grease zerks. Now the entire column, ignition is locked up tight. I can't turn the key, remove it, anything? Thoughts? I'm stuck
View 14 Replies
My boss gave me a 2002 f150 if i can get it started. No key and no paper work in order to get locksmith to replace key. The only way i have noticed to get it started is to drill through cylinder to get it out. Need to know how to get it going?
View 4 Replies
Steering column recall ? The ford sites don't have much info yet. What is involved steering column replacement ? Computer reprogramming to sove the issue of the steering ?
View 1 Replies
My `88 Aerostar needs a replacement steering column. I believe everything can be swapped over therefore color of steering wheel does not matter. Cruise control buttons and tilt are a must. I would like to find one that is tight(er) and not sloppy floppy like mine is slowly becoming (143k miles).
View 1 Replies
Took my 99 XLT super cab to a Ford dealer to have a new key made (I have only one so can't do it myself). I was told the PAT (Passive Anti-Theft) module wouldn't communicate with their system.....
As I understand it, the PAT module communicates wirelessly to the key module under the steering column. Since the PAT module is obviously working (the truck cranks, starts and runs fine). What are they talking about?
View 14 Replies
I want to replace my steering wheel. Will this puller work for that job?
View 5 Replies
I am working on a salvage car that I bought recently. It was stolen, they cut the wire harness to the GPS system and messed up the steering column. I replaced the steering column with a 2012 GTI steering column and steering wheel. I bought a RNS 315 but I dont have any luck finding a wiring connector for it. After I installed the steering column, when I turn the ignition key nothing comes on in the gauge cluster. I know the car wont start till the key is programmed. My question is do I need to fix the wire harness so that when I turn the key ON the cluster will light up? Where I can find the connector for RNS 315. Regarding the airbag, will a GTI airbag work on a Golf TDI?
View 1 Replies
I took my '02 Passat in a couple weeks ago when the steering wheel controls and horn stopped working. They replaced a fuse. About 10 days later, I experienced the same problem. That time, they said that the steering wheel was all shorted out and needed to be replaced. Five days later, again the same problem. Now the dealer says it's some faulty switch from the fuse panel, which caused the short of the old steering wheel. Since that wasn't replaced, that's why I experienced the problem again. Could that have been the only problem? Or could that really have fried the steering wheel, too. Am I being taken, and do I need to fight to get some of that money back? Or is this legit? How can I verify that what they said was the problem actually was, and that I'm not left paying for their mistaken diagnosis?
View 3 Replies
I am replacing the high pressure power steering line on my 2000 Lightning and have a question about the fitting that goes into the steering gear. The new hose came with a black rubber o-ring that the instructions seem to indicate goes on the end of the steering gear fitting. The problem is that I did not see any o-ring on the original hose end or in the steering gear itself and the hose did not leak there (it was leaking on the pump fitting). Should there be an o-ring at the end of the fitting or does the fitting go on without it and uses a metal to metal seal? If replace this hose, did you use the o-ring or leave it out? Does it go on like this? Or like this?
View 4 Replies
How to unlock the steering column of a hybrid push button camry?? Im so confused and can't find any information.
View 4 Replies
Is it possible to change the ignition switch without the key. Problem is my old key broke so im replacing the whole switch.
View 1 Replies
This started today, when I turn off the ignition and remove the key the radio stays on and the steering column does not lock. The guy at the dealership suggested spraying wd 40 into the ignition. No go.
2008 sonata.
View 3 Replies
Well now I have to replace the multi function switch due to moving my steering wheel and the headlights sometimes working and turning signals not working. I saw a great video on youtube about changing a Multi Function Switch and it shows where the air bag needs to be removed. I was hoping that since my truck is an older 1997 F250 LD I wouldn't have to remove the airbag. Is there a way to do this w/out messing with the airbag on the 1997?
View 1 Replies
I am having a little issue with the ignition in my car. I had the typical no headlights/wipers/heater etc. so I ordered up a new ignition switch and when I went to replace it, the switch fit perfectly and had the correct part number but when I put my key in to try and start the car I couldn't even turn the key but when I put the old switch back in it would turn just fine. Also when I removed the old switch I noticed the red wire going to the switch was slightly burnt right at the terminal.
Here is the basic procedure I did:
-Unhook negative battery cable
-remove lower dash/ center console
-remove switch
-install new switch
Whats this little metal piece? I did not see that when I did mine...
View 10 Replies
So, I have an 89 Ford Ranger 4-wheel drive and the steering wheel is locked up (along with the ignition switch), neither of which will turn or budge. I've been told to shake steering wheel from side to side while trying to turn key--but after fifteen minutes of that (quite a workout) bupkis, nada, nothing. So, other than taking a sledge hammer to the whole truck? Is there a way to simply break loose the mechanism (I don't need the security aspect of the locking wheel/ignition, since I only use this for "farm use". But I really need it fixed.
View 9 Replies
I just had the ignition switch replaced on my 2001 Toyota Sequioa. Now my blinkers work but will not shut off after I complete the turn. Additionally, the blinker "stick" is very hard to move in either direction. I plan to take my car back to the dealer and politely request this blinker repair be warranty work.
View 1 Replies
