Ford F-150 - 1997-2003 :: Runs Rough And Stalls When Stop Or Rolling To A Stop It Would Die
May 23, 2017
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
View 2 Replies
Advertisement
My 4x4 only locks in when i lock it in and then go drive around, and i know its locked in when it gets hard to turn on the road. So i stop and play with it in 4x4 to see if it will go into 4 hi and it does but then after about 5-10 minutes it disengages again. I've checked the top portion of my vacuum lines, replaced my actuator on the front diff and I've made shore that my selonoids are working, and they are. I'm lost.
View 4 Replies
I have a 1983 Honda Accord (manual with nearly 200,000 miles) when rolling to a stop or at a stop rpms drop below 1000 and it stalls out. I can start it back up without hesitation.No hesitation at initial startup or after sitting short or long time, it idles while in park rpms about 1000.When I feel the engine about to stall while rolling to a stop or at stop, if I put my left foot on the brake pedal, slightly step on the gas pedal with my right foot it prevents the engine from stalling. At stop if I put in park, rpms raise and don’t need to give it gas.
I'm unable [& unqualified] to work on my car. Given I drive only about 1,000 mi year; my alternate form of transportation is a bus or kindness of friends, I’m on a limited income, cannot afford to buy/ spend more than 2,000 -- my question if 2-foId, 1. is it possible that something it is nothing major and worth repairing/replacing (ex. air control/idle air bypass valve, a dirty throttle body or even carburetor)?2. Or, as discussed with one mechanic, since the car is 33 years old, during or soon after repair other problems (dried out vacuum hoses or major) will follow. Plus, parts can be difficult if not impossible to replace as a I spoke to mechanic pointed out.Given the car’s age is it worth repairing?
View 5 Replies
2001 f150 supercrew 5.4 triton... Recently did a tune up plugs,coil packs,filters,belt the whole 9 yards. The truck starts fine accelerates great and cruises down the road great without missing a beat.
But every now and then when you stop at a light or park it begins to idle down to the point where it almost stalls. When it does this i usually stab the throttle and it revs right up without missing a beat and idles fine for a a while then same thing all over again.
Could this be the idle air control? Seems like something simple due to the fact it runs down the road and accelerates like a big dog.
View 9 Replies
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
View 3 Replies
I have a 2004 FX4 5.4 with about 113,000 miles on it. Lately, when towing the camper (around 7000 lbs), truck runs great. However, when I come to a stop, it idles horribly and even stalls sometimes. When I rev it up, runs fine again. It only does this after towing when engine is under load for extended periods of time.
The only code it has ever thrown was for bank 2 camshaft over retarded. My thought was that it could be VCT solenoid for bank 2...
View 2 Replies
I have a 1997 Buick Park Avenue with a 3800 series II motor that runs perfectly in dry weather. However, in wet conditions, rain melting snow, etc. it will begin to miss and throw out a P0300 OBDII engine code. This is the code for multiple random misfire. If I leave it to idle on its own it will get worse and die out right. Sometimes restarting it is an option though it still runs rough, but I can limp it to somewhere I can work on it. I think its electrical, since it doesn't seem to get the spark it should though fuel doesn't seem to be a problem as you can smell it after a bit of cranking.
I've been battling with this thing for over a year so far and have replaced the following, ECU, all 3 coil packs, spark plugs/wires(newest parts), mass airflow sensor, cam position sensor, ERG?(emissions deal I believe, mechanic friend put it on) valve. I had the battery trickle charged and tested at an Autozone, I haven't had the alternator tested yet.
Its a very frustrating problem, as far as I can tell I've replaced everything on the ignition system with the hopes that it did the job only to get stranded during the next long rain. It does take quite a while in wet weather for it to start acting up, but once it starts missing a little bit, it doesn't stop until the entire engine compartment has had a few days to dry. Engine temp doesn't seem tosolve the problem dry out. I'd also like to note that I've noticed on this latest trouble that the interior lights have been flickering and headlights too. It may have been doing this earlier, but I hadn't noticed if it was. I'm going to check what kind of voltages the alternator is throwing out next time I have it running.
View 6 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
View 4 Replies
I am the original owner of a 1993 Nissan Altima. My mechanic states that the air intake (part # 165751E400 "air duct")has dry rotted. He put some silicone hoping that would seal it but it did not work. The part is no longer available from Nissan. The car runs very rough and wants to stall when coming to a stop. It also smells like gasoline in the cabin and the gas mileage is terrible 17 mpg. I have tried to find someone who could custom make a new hose with no luck. My mechanic stated that pulling one from a used car would have the same problem. What other options are available? The hose is about 8 inches long and about 3-4 inches diameter. It has other small hoses that attached to it. Do I throw away an otherwise reliable car?
View 4 Replies
My truck runs rough/bad when it rains or is damp out. It stutters and had no acceleration. I just had a new fuel pump put in January. It improves after a while on the road. If it's wet, my travel sucks.
View 6 Replies
2004 Trailblazer 6cy. 2WD - has been experiencing a very rough idle, engine shudders - no matter how long it's been warmed up. Wants to stall off red lights and at very low speeds. Not throwing any lights yet - but the speedo is out ( a cam shift typical problem for this car) so I don't trust the console for lights. Worse when the heat or air is on. Rides fine with more gas/higher speeds. Definitely worse in colder temps but continues even after 40-50 mins of driving. I've heard a number of things, but can't afford to fix them all. I've heard plugs, dirty throttle camshaft, sensors, cam actuator solenoid, etc. All seem to have people who said it fixed and didn't fix the issue. Worried I'm going to stall pulling off a stop and rear end someone any day now. Where do I start!?
View 2 Replies
I have a 2003 Ex with 7.3L. Occasionally my truck stalls while decelerating, typically when hot and going slow or coming to a stop. I had my friend who works for Ford put is on their diagnostic system and did a buzz test and found no issues. I replaces the CPS. What to look for to resolve?
View 1 Replies
I have a 1987 automatic Nissan Sentra XE- two barrel carburetor, mileage 212,880. The car has one major problem that is going to get me hit driving it in rush hour. Most mechanics will not touch the car due to being carburetor.
Let me explain: the car idles real rough at times, hesitates at stop signs and red lights, about stalls out on me when I press the gas pedal to go or when I start to make a left or right turn. However, other times the car has little to no hesitation and idles perfectly. I have not been able to come up with a good a pattern with this problem.
I have replaced, fuel pump & filter, spark plug wires, coil, distributor, ecu computer, ran sea foam through the fuel system and have replaced many vacuum hoses.
View 4 Replies
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
View 3 Replies
Well I have 8000 miles on my 12 Eco now and it has been the best vehicle I have ever owned but it has always shifted rough, Mainly into 3rd gear but you could always feel it downshifting when rolling up to a stop sign also, I just assumed it was the way it was suppose to be. This morning I was driving it and noticed it was shifting very nice and smooth, no downshift braking or the other little issues.
I also noticed the the select shift was turned off (the numbers on the dash 1-6) if you push the + button on the shifter you can turn them off, I have had it turned on since I bought the truck because I kind of liked the display but anyway with the select shift turned off the transmission shifts very nice, I turned it back on and the rough shifting returned, Try it on yours to see if it changes.
View 5 Replies
I have a 2000 E350 boxtruck with a 5.4 auto. The motor is a new rebuilt with about 4000 mile, coils were replaced with motor, injectors were rebuilt with motor.Today (500 miles from home) the truck died. I was going up a slight hill on an interstate. It will still start, but runs very rough and when I put it in gear and step on the gas it dies.
So I had it towed to a garage. While pushing it into the garage I noticed my gas cap was missing. I know it was on 45 min earlier because I got gas. Did I forget to put in back on? probably.. But I wondering if the missing gas cap could cause the truck to run bad,vary bad?
View 14 Replies
My car at first had issues just not starting. Now it starts just fine but it stalls when I come to a stop at lights or signs. This past time it hesitated before stopping after it turned off. When it turns off the lights and radio are still on. I have taken it to a nearby mechanic and a Nissan Dealership....Nothing... Nissan Pathfinder 2003 SE ....
View 4 Replies
I have a 2001 Ford Excursion Limited 7.3l with 199,980 miles on it.
It has a TS-6. My first problem is that when I come to a stop or slow down to a crawl then press the accelerator the engine stalls and dies. I have looked and looked at threads and can not find this example anywhere. There is no pressing the pedal and it remains at idle. It dies, shuts off, quiets. I have thought icp, tps, ivs
Second problem is that a/c is blowing hot. Other than being out of Freon, what could be other things to check. It does sometime go to default, but has done so in awhile. It does not blow cold in rear and hot in front. They both blow hot. I have replaced the pvh sensor.
View 1 Replies
My F150 with 175,000 miles on gave me a the ol' P0305 code indicating misfiring in cylinder #5. I changed the plugs and wires using Motorcraft wires and Motorcraft AGS34FM plugs.
Now the truck idles fine, does not give a OBD code but runs rough at 2,000-2,500 rpm. Tried it out on the highway and it started "bucking" a bit. Not sure what to try next.
View 2 Replies
