My F150 5.4 V8 is running to lean on both banks according to my code reader. I have replaced the fuel filter cleaned up the air filter and I am about to put in seafoam in the gas tank to clean out the jets and carb. I thought fuel pump but have never had to deal with this before. I just bought the truck last thursday. Also my gas gauge is stuk at empty and the low fuel light is on ....
View 14 Replies99 F250 LD 4x4 w/5.4 - 218k .... Check engine light just came on so I had the trouble codes pulled. 071 and 074 . Lean on banks 1 and 2 . Truck is running fine as far as I can tell. I know it can be o2 sensors, pcv, maf sensor or loose vacuum line somewhere. I just put a new motorcraft pcv valve on before this happened so I rechecked the lines , all seem to be fine. Is there a inexpensive scanner that I can check the o2 sensors without just throwing money at new ones.
View 3 RepliesI have a 2000 Ranger, with a 4.0 V6, 4X4, with 175,000 miles and it still runs great except the check engine light is on and it is saying that both banks are lean. I put in new plugs, all 3 O2 sensors, cleaned the MAF and checked for vacuum leaks, all to no avail...
View 17 RepliesWhat does this mean?? The o2 sensor(s) is reading lean?? 2001 F150 4x4 5.4
There was also an evaporator system code, but I think maybe someone left the gas cap loose? I unhooked the battery and it cleared everything. Truck started fine for a few tries. Will have it driven tomorrow to see if codes come back.
My reason for this is it was getting hard to start. I confirmed that fuel pump relay was not coming back on when cranking every time. Randomly it's fine, other times it won't start. Noticed it had CEL light, had it read at local Azone.
Don't know what to do about the "lean" issue? What would tell the pump relay to NOT turn on?
I removed the cover from the relay and inspected points, they were fine. Check with ohm meter=good. Watched it function without the cap on it. Would prime every time, but not come on when cranking every time.
Just put a cold air intake on my 99 f150 with a 4.6. its a CAI with a 4" tube and its not an oiled filter. there is NO vacuum leaks, the mass air flow sensor is clean. I am getting the codes 171 and 174 now and i know its from the intake because that's when it started running lean. Is there any way or anything i can adjust to fix this other than buying a 300 dollar programmer?? If I take it to a ford mechanic will he be able to fix this?
View 11 RepliesWell I got the ubiquitous "Bank 1 Too Lean" code this morning. Yesterday I changed out the PVC Valve, Elbow and Hose assy.
I changed out the hose from the intake to the canister purge valve on the firewall next to the master brake cylinder, that one was like dust.
Today I'm changing out the rear O2 sensors, but I may change out the fronts when they get them in (very rural area hear).
I'll keep looking for vacuum leaks and change out the MAF sensor. I hate to think it may be the intake....
My truck is a 4x4 lariat, I've replaced both dpfe valve and egr, and the intake manifold gasket. Still getting the egr insufficient code. It went away from a few months after replacing the intake manifold gasket but has returned. Where do I go from here? I vacuum tested the egr and that's working fine. Should I buy ANOTHER DPFE valve? Where do I go from here I'm desperate.
View 14 Replies2003 f150 supercrew with 166,000 miles on it. Daily driver. Service light randomly comes on and when code reader was put to it shows "left bank running lean." Will clear it and will randomly come back on. Truck seems to be running fine. No issues engine. Bad sensor? Or bad injector? Maybe way to test?
View 1 RepliesI have a rough idle. I have replaced upstream o2 sensors, plugs, wires, fuel filter, dpfe sensor, cam sensor, and cam synchronizer. This has only moderately improved my problem. I still have the right bank, left bank too lean codes. Could it be something as simple but hard to find as a vacuum leak?
View 8 Replies2003 F150 v6 2wd 170k ... For a year I've only had codes P0171 and P0174 (lean bank 1 and 2). I was told it wouldn't hurt anything... I think now I should have taken care of it.
Anyway 3 weeks ago my truck started running a little rough. It was sputtering and had trouble getting up to speed, sometimes also the air switches from vent to defrost until switch gears and rpms go down. It gradually got a lot worse over 10 days while part was otw. A week ago i changed MAF and cleaned the black thing it's inside of. It started running better but still not good. I pulled my small trailer 2 days ago and it got worse after dropping the trailer.
Today checked codes at AZ and lean codes are gone and have p0304 (#4 misfire) and p0316 (crank sensor problem). Is this related.? Also Right before all the trouble I changed battery and alternator. Also i read online that MAF needed 2 weeks to relearn the way I drive to get correct gas/air ratio? Is that correct?
Also I read so many different things I needed to do during installation... Some say I need to turn key to the on position after unplugging old MAF then plug new one in... turn key to on position 10 times, Rev up engine, drive it rough for the first 2 minutes... etc. Is there a correct way to do it or is it vehicle specific?
Should I start by changing spark plugs and coils? The guy i bought it from and trust said he changed spark plugs right before I bought it. Will it ruin truck if I drive it? I've read so much but everyone says so much different things on the same topic. I'd what to start with or if this is related.
My truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
I have a 2000 f150 with a 5.4 past few months it has been throwing a p1151 code meaning it is coming up lean on the driver side. I just changed the plugs and it didn't work, neither did changing the fuel and air filters. cant find any vacuum or exhaust leaks. Replaced a bad injector along with the spark plugs and its still coming up lean.
The truck also seems to bog down at about 50-60 mph if i let off the gas and coast it will drop about 300 rpms. It has me confused and annoyed, i have true duals with glass packs could that be causing it?
Here are the codes I'm getting:
P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean
are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 RepliesI've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......
View 7 Replies1998 ford ranger 4.0 ... fuel running lean ... how do you adjust it??
View 3 RepliesI have a 1999 Ford f150 4.6L automatic. My check engine light had been on for awhile so I dug out my DTC code reader erased it, came back on 10-15 minutes later. I got the code P1131 sensor indicates lean which you would think is the O2 sensor a week later it won't start. Then randomly a couple days later it starts then that night it didn't. Hear is the parts that confused me. I don't believe an oxygen sensor would cause it not to start, it's cranking nice just won't turn over. And when you get the code P1131 I believe it bay 1 where the readings are off Well here's my readings.
Fuel system 1 CL-FaultCalc load 34.1%ECT 201.2 FSTFT B1 -1.6%LTFT B1 0.0 %STFT B2 -1.6%LEFT B2 0.0%ENG RPM 1101VEH SPEED 27 MPH
It looks like to me bay 1 and 2 are off? I'm not mechanically challenged, but not a mechanic either, I do most my own work on my vehicles..
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
i have a 2005 f150 4x4 5.4 3 valve. it ides good but when it is in on it splutters, and also feels like dead cylinders in passenger gear. i checked the codes the other day and i had a cylinder 5 misfire. so i cleared it and today checked again and had running lean bank one and cylinder 8 misfire, then checked one more time and had cylinder 7 misfire. I am sure it is a bad coil but how do I know which one?
View 2 RepliesI've tried everything I can think of and it still runs sluggish.
1. Had dealer change plugs
2. Changed Cop's
3. Cleaned MAF sensor
The 5.4L has slight miss and doesn't respond well at all when trying to pass or going uphills.