My 1997 ford f150 4.6 triton runs hot after 1 minute of idling. I changed the two coolant sensors, flushed the radiator, and changed the thermostat. I also went to have a diagnostic done at two different places and nether one could get a reading....
View 14 RepliesMy daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?
I have a 01 f150 with the 5.4. when it starts it takes a minute or two to do so.. After I shut it off and try to restart it won't unless I turn the key on and wait. I checked the pressure and when idling its running about 28 soon as the key is turned off it goes to 0. Is my pump bad??
View 8 RepliesI am Hearing a series of 5 one second tones about 1 minute after starting. There is no indication on the dash that anything is wrong. There are five tones about one second long. They repeat five times and then stop. The truck appears to be running fine. What is this?
View 1 RepliesHave a 2001 F150 5.4L Super Crew that hates temps below 50 degrees. It has new O2 sensors on the pass side banks, Map and Air charge temp sensors as well as a new IAC motor and a fuel pressure regulator. I've went though all the vacuum lines and replace the cracked dry ones as well a checked for vacuum leaks.
On initial start up, the truck will run and idle fine. after a minute or so, the rpm will fluctuate radically from 500 to 900 RPM. When driving, and you come to a stop sign, the engine will do the same almost seeming to stall. Once the engine reaches full operating temperature, then it runs fine. It always seems to throw P0171 / P0174 when it does this.
We've sprayed all around the intake and cannot find a leak anywhere. I do find it odd that this is a temperature related issue based on the engine operating temperature and the air temp in general. 50 degrees seems to be the turning point from running to just being a hand full until it warms up.
My 2000 f150 with a 4.6 and just about 200,000 miles stumbled for a minute then died, no engine light came on. It wanted to restart and almost did a couple time's but no go. which leads me to believe it has spark. after about a 30min cool down it started and ran fine like nothing ever happened. Got me home. then the next day same thing died and started after it cooled. Has done this a few time's.
I had put a cheap O'riely fuel pump in it a couple years ago. but i hear if you run your gas tank low on gas a lot (which I do) the pump can get hot and you can toast it. Does the fuel pump is the issue or could i have another problem. And BTW in the past year I have cleaned the EGR port's on the throttle body, put a new egr valve, and fuel filter. And i checked the fuel pressure to had 40...
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
2003 F150 5.4L Tow Package 140k miles... Had coils, all plugs/wires replaced two years ago due to vibe climbing hills. Now at startup in the morning for a minute or two during idle, the engine vibrates severely then subsides and runs fine rest of day. Doesn't do this every morning. Truck lives in FL. The issue is either temperature related or moisture related. Ford service has the truck presently and attempting to diagnose from an overnight stay. They already 'fixed' the problem last week by replacing #1 plug/wire and resetting the power control module (pcm) but two days later the problem came back. Tech said today that the plugs currently installed are Bosch (any issue with these plugs?)
2003 F150 5.4L 140k miles
2011 Expy 5.4L 44k miles
So my car was fine when I drove to the store, with no AC on. After that, I wanted to drive to a hotel, which is 1/2 of a mile away. Before I drove there and after I started my car, I blasted my AC (turning up to #3). On my way there the car was fine. When I drove into the parking lot and braked, the car suddenly turned off by itself showing the battery light. After the car turned off by itself, the fan (not AC..
AC doesn't run when engine is turned off) was still running. I freaked out, immediately turned AC/Fan off and restarted it. It was successful after the first try. So my question is...what caused the car to turn off by itself? Is it because of my AC? I know FOR SURE...it's not because of
1. timing belt because i recently changed it.
2. battery but i installed a brand new last summer.
My 1997 f150 5.4 has started an idle issue. The truck when started will idle around1200 rpm and not settle down After driving a bit it will drop down around 800 and idle rough and sounds like it has a plug fouled. As soon as you give it gas it clears up and sounds fine, then drops down an idles rough.
Checked for vacuum leaks but don't see any. pulled the MAP sensor and cleaned it, but did not change.
Yesterday had my truck 1999 ford f150 v8 4x4 it was just sitting there idling fine then it all of sudden sounded like it was about to stall then began idling fine again. It has some hesitation on take off and when going about 40 mph
View 4 Replies2004 Prius with 109,000 miles. It's been in an accident before (and you can tell, the front right fender is a bit misaligned and the doors have a paint covering abrasions).
However, the car is making a ticking noise every minutes or so. The sound is originating in the Hybrid Synergy Drive converter inverter box and about every minute for about 5 or 7 seconds or so there will be a ticking or clicking noise. This happens when the car is idling, driving, and even a minute or two after car was shut off. The mechanic next door to the dealer didn't know what it is and the dealer is giving me a 30 day. What could this clicking be?
My 2004 F-150 Heritage with the 4.6 was running great until yesterday. Went in the store and left it idling, when I came back out it had died. First time it has ever done this. I started it and it started right up but misses bad. Checked it out and found all 4 cylinders on the drivers side are dead. The check engine light is on and the overdrive off light on the shifter is on. It will start right up and everything else is fine, oil pressure, coolant, etc.
View 9 RepliesMy 03 with a 5.4 has been hesitating a when you accelerate and cutting out as well as idling rough and die when you slow down. It does all this intermittently. Not every stop or every time you accelerate. I first got a code for the MAF and both banks running rich (PO102, PO172, PO175) so I cleaned the throttle body and MAF. The running rich code came back (PO172, PO175) so I then changed the MAF and air filter . It seemed to work for a day or so then my light came on and I figured the same code was back but to my surprise it was now both banks running lean(PO171, PO174) so I took my MAF back and got another one. It hasn't set a code yet but it is still running poorly. I have changed all the COP's and plugs as well ....
View 13 RepliesI've owned the truck for 8 months, did a fair bit of maintenance in the first two months (plugs, tranny fluid change, maf cleaned, o2s replaced), 320,000km runs very well, no codes.
When the truck is in gear and I put my foot on the brake after a second or so idling, the engine shakes. Releasing the brake, the shake stops, but it does it every time. Also, the belt or one of the pulleys will squeak a bit at the same time, but only idling with the brake on.
It doesn't seem like it is a serious problem, but what and why? My instincts are telling me it may be transmission related.
When start my Caprice (1986) carb-- I used to step on the gas pedal (half step is more than enough) to start the car.
Once the car started it's idling normally, but suddenly after 3 or 4 minute the sound of engine go high idling as if I stepped on the gas and that is remaining for long time even if I step full gas, and if I turnoff the the engine and pull out the key, the car will remain working hardly and shaking like crazy before it completely stop.
What is the problem with my 86 Caprice Brougham? is that problem easy to fix?
I have a 99 4.2L 5 speed reg. cab swb. It recently started idling high (which returns to normal at a stop after 3-5 seconds). While in neutral and in motion (coasting) the idle is around 1500-2k (idle=no throttle input from me). The first time it did this it took a while to start (7-10 seconds) and smoked like you wouldnt believe for about ten seconds. Smoke cleared, eyes returned to normal size, heart rate returned to "normal", but the high idle remains. Drives me nuts. No CEL, no codes, just a fat bald man scratching his head and a little nervousness.
View 5 Replies1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
I've tried everything I can think of and it still runs sluggish.
1. Had dealer change plugs
2. Changed Cop's
3. Cleaned MAF sensor
The 5.4L has slight miss and doesn't respond well at all when trying to pass or going uphills.
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.