My husband's starter went, so he took it in to be rebuilt. After my husband reinstalled it, as soon as he connects the battery up, the starter engages without the ignition on (not even a key in the ignition). Did the guy who rebuilt it screw up, or is there something my s/o might have done wrong when putting it back in?
View 11 RepliesI just had my tranny rebuilt it doesn't shift hard all the time but it does from time to time going from 2nd -3rd and 3rd -4th I thought being new it may need to soak up some fluid so the bands can swell so I ask the shop that rebuilt it that question he said they soaked them as they rebuilt it so they should be swollen already then he proceeded to tell me it was electrical is he telling me the truth because the ck engine light isn't showing any faults and if it was electric shouldn't that have been fixed in the shop while it was being rebuilt if it was interior electronic?
View 1 RepliesOk so I have a 2002 f-150 4.2. I was replacing the PCV elbow that always crack and I figured while I'm down here, I might as well replace the PCV valve as well. I have the PCV valve that has 3 connections, 1 to the crankcase and then 2 "vacuum" type connections connected to the water pump and is full of coolant of course. What am I missing here, I though sometimes these things were connected to a vacuum line, is this some kind of heater for the PCV?
View 12 RepliesI have the notorious PO171 and PO174 codes on my 2003 5.4L that come back whenever I erase them. I cannot figure out the problem. Whenever I start the truck it cranks for 3-4 seconds before it finally fires, then rpm's are very low, then they finally pick up. I have noticed a loss in power as well. I have completed a full tune-up (spark plugs, coils, boots, filters, etc.)
I have checked the vacuum and PCV lines numerous times, I have yet to find a leak. MAF appears clean. I am running a K&N CAI setup. O2 sensors a good, replaced the gas cap. The only other problem I can see is a bad PCV valve? I hope it isn't a manifold gasket. The truck has been very well maintained and still looks brand-new throughout at 250,000 miles.
1986 ford f150 standard cab, manual trans with 3 plus overdrive.
1989 302 rebuild v8. When trying to start occasionally the ignition continues to turn over..
Even after the engine fires, the starter continues to turn over until I have to disconnect the battery to stop it. Then it fires up fine afterwards what could the problem be.
I'm thinking the starter, or the ignition switch but I also heard it could be the starter solenoid.
Starter Removal, The top bolt is a bugger.
View 5 RepliesThe starter on my kid's truck doesn't disengage and continues to turn over after the ignition is off. I have seen a few posts on this but have yet to find a clear troubleshooting path and it seems a lot of money wasted on new starters, solenoids and new ignitions.
View 4 Replies03 F-250 5.4vStandard Transmission
Thought my battery was no good , so changed it. Didn't work it just kinda bumps the motor but doesn't turn over.
Thought it must be my starter then , bought a $200 starter and changed it , still doing the same thing. It did start after changing the starter but wont now.
Neutral safety switch?
I have a '99 F-150 SC, 4x4, 4.6L, with 48,000 miles. I drove approximately 15 miles, then parked for 20 minutes. When I returned, the truck wouldn't do anything when the key was switched to start. It's as though there was no power going to the starter. Could it be a problem with the immobizer system, or just a freak incident with how I handled the key? The truck ended up starting after another 15 minutes and has consistantly started for the remainder of the day.
View 4 RepliesStarter problem with my 1999 Ford 5.4 f150. Last few days I’ve had to cross the solenoid terminals in order to start up. After replacing the solenoid the starter would not disengage. Put the old solenoid back on, crossed term and the starter did the same thing. Bought new starter (what a job finding the upper bolt) replaced old one, and I’m still hearing the starter running along with the motor. What else?
View 11 Replies1998 f250 4.6 4x4. In park the starter engages with key on . Ounce running the starter is still engaged in park and neutral. No engagement in the drive gears. Changed the ignition switch and neutral safety switch on the trans. When key is off instrument cluster is still on.
View 3 RepliesI got a 1997 f150 4x4 4.6L had to replace fuel rail after a couple holes were rubbed in it and caused a fire, but now after two weeks of it sitting at the dealer, I wasn't gonna pay for a fuel rail to be put on so i had it towed home and I did it, however now when I go to start it, it just clicks. So I have the battery tested and its bad so it was still warrantied so it now has a new battery and i also replaced the starter solenoid while i was at it. But still just a click when i try to start it. I had the starter out and bench tested it and it went but went slow and looked very old and tired, I am thinking i need a starter now because its a click from the starter, like its trying to go but isn't strong enough.
View 3 RepliesI have 98 f150 with 4.6 starter went so I put a new one on wich was a hassle and it tries to turn but just wont as if the motor is seized. I had been hear a loud howling sound from what I think is the ac unit and the ac line burst after trying to start. Would a bearing or something with the AC be enough to stop the engine from turning over? Or could it maybe be a wire connection problem? To me it sounds like a starter trying to start a seized motor but I cant see that my motor would be out it only has 190 000km and the oil looks good. but we couldn't turn the motor over with a ratchet? The truck had been getting gutless. I am stuck...
View 4 RepliesI just bought a 2000 f150 4x4 ex cab with the 5.4. Once in a while when starting, there is a grinding and the starter won't engage the flywheel. The truck has only had 17000 miles put on it in the past 4 years, and has sat quite a bit. Could the starter gear be gummed up and not engaging all the way, or should the starter be replaced? Or could poor contact on the cables cause this? Or is this a flywheel issue?
View 14 Replies2000 f150 4x4 5.4auto tranny.
When I turn the key, sometimes i have a time delay before the starter kicks in. I replaced the relay on the firewall and no change. A couple of days ago I started the truck but the starter did not turn off when the key was released. I had to turn the key to off then back to run to get the starter to stop. Now today, I nearly got stranded by it. It took several attempts to get the starter to kick in.
To me this seems like a relay sticking. What should I try next?
My truck has started fine every time I've turned the key except for last night after work. I got in had all the lights on the dash and dome lights. I turned the key and nothing. Not even a click. Hooked it up to a company truck and it fired right up and ran fine. Drove home shut off and then started it a little later and it started fine. Then this morning it wouldn't start. I hooked up the jump pack and still nothing. I drove my fusion to work and when I got home I went out and it fired right up like nothing happened. Does the work sometimes not work other times sound like the solenoid on the firewall? 2000 4x4 4.6 auto 253k miles
View 4 RepliesI might have a chance to pick up an 1997 F150 with a 4.6 pretty cheap. He has replaced the ignition switch and lock cylinder, Says it keeps turning over until you put in in gear. In my experience a solenoid that is sticking wont stop until you disconnect the battery, just wondering what people think it might be? I am thinking I will just put a push button stater to make it work if its a wiring issue.
View 3 RepliesI rebuilt the HV battery w/(tested) Gen II cells on a 2001 that I purchased cheap knowing that the HV was bad.
View 8 Replies2004 F-150 heritage : 12 degrees F yesterday. clicked (firewall solenoid) but starter was not pulling amps. After putting a jumper pack on it, after about 30-40 clicks it took off, never to work again.....towed it home with a rope.
2000 F-250 Super Duty : 7 degrees F today, did the same except you could tell the starter was pulling amps. Took a lot of clicks and engaged but I let off too quick, another bunch of clicks and it started. Once I moved it, I tried it a bunch more and it seemed to work, however I do not trust it.
2001 Crown Victoria : 7 degrees F today, the first turn of the key was nothing but a click, and the 2nd turn it worked fine. After moving it worked a bunch more times.
Whats up with the cold temps and the starters?
I have an 02 f150 5.4 4x4, drowned it a while back, thought i had hydro lock, crank can be turned by hand though as far as i can with a wrench, so internals seem to be fine, no bent or broken rods that i could tell, ripped everything apart cleaned it up put it back together, new fuses, new ignition relay, new starter, alternator and battery as well, turned the key to on and got all my electronic stuff back up, turned to start and it all goes dark, which i assume is because at that point its sending power to the starter, but the starter didn't turn or crank the engine...
So question being when i put my new starter on is it possible that i might have crossed a wire or something that would cause it to not crank? and due to the fact that I had water in it, and had hydro locked it, all my plugs are out, now I know that spark is needed for the engine to run, but shouldn't be needed just for the crank to turn right? question being is that once i fix the wires on my starter, I am looking for initial crank before start up, so do i need to put a plug or two back in and hook them up to make it crank? or will it crank without them? and yes I did replace all my fluids as well.
After getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 Replies