Got myself a brand new old truck. No radio and all the wires had been cut. I just printed of a wiring diagram from web and went to work I am now on my second one and it has the same colors for two different speakers!! The first one was completely wrong. Looking for a good wiring diagram for a 97 f250 super cab.
View 1 RepliesAnyway, I'm gimped in my left shoulder for a while and I'm trying to do what i can with my 03 F150 Supercrew /4bt Cummins conversion. I am using a Dodge 47rh tranny and need to know the wiring for the 4R70W so I can hook up my 12 + ignition wire, back-up lights and neutral safety switch. I'd like to build my wiring harness.
View 6 RepliesI am trying to add a keyless entry to the already equip, power door locks but am having problems figuring the wiring schematic
View 8 RepliesI just bought a 2000 Excursion limited v10 4x4. I'm going camping this weekend so trying to install my brake controller. I found the plug but noticed these wires dangling. I can't see the back of the harness. I'm afraid the PO may have cut them to install a universal harness. How to recognize them? I don't want to buy a ford specific harness if the wiring has been cut.
View 3 RepliesI am working on my son's 1997 F-150, 2 wheel drive, 4/6L truck. He was driving it when the gauges and the tach stopped working. I replaced the cluster and it still blows the fuses. The five amp fuse that is specifically for the cluster doesn't blow. It is a twenty five amp fuse that also power the overdrive circuit, etc.
After replacing the gauge cluster I installed a new fuse and the overdrive button on the shifter started smoking. Where I could get a wiring diagram of this circuit so I can see how it is wired.
I removed the rear radio controller from the back of the console and installed a power inverter in its place. It fit great and everything went smoothly. I should have known it was too easy... I now have no sound coming out of the rear speakers. I assume there is a way to jump the wires to allow the speakers to work, but I'd need a wiring diagram. Right now I have the controller hooked up and buried in the console, which I guess is fine. It's just annoying.
View 10 RepliesI'm currently trying to swap out the standard AM/FM/CD for a DVD receiver with backup camera, and need to find out the proper wiring colors and pin position. I'd rather not send it to a stereo shop, as I've seen a lot of hack work by so called "audio installation experts", and besides.. I have a shop and can do the work myself.
I tried looking through AllData, but since my truck is too new, Ford doesn't release a lot of technical info for us in the aftermarket. Looking for a link to a Ford diagram?
What is the factory radio wiring colors or know where I can find a diagram?
View 14 RepliesI just purchased everything for my audio and I need wiring behind the radio. I purchased a Audio Control LC6i and I need to know which wires are for which speaker. I tried the Hyundai tech info website but it doesn't show anything when I go into the diagrams. By the way I have no navi just the steering wheel controls.
View 12 RepliesWhere I can get a radio wiring diagram for 2003 F250 Crew Cab?
View 1 RepliesI can't find a wiring diagram for the UVCH pigtail anywhere. The one that came with the harness assumes the old one was still connected. My wires were burned through and I need to know what colors to wire in from the truck to the new harness so everything matches up.
View 9 RepliesI am looking at putting a couple small LEDs in the pinch weld area under the doors on the cab. I want to have them come on when I open up a door. Where is the best place to grab power from the door switch circuit for that? The passenger side I was thinking of grabbing it where it goes into the sleeve between the cab and the door, but on the drivers side there are a lot of things in the way to get to that point. Can I pick it up down in the door jamb area? Is there a wire going to the dome light there?
View 8 RepliesI'm working on a truck for a friend's mother and all of the tests that I've done point to the fuel pump. However, to make sure the pump is getting voltage past the large connector block under the cab, I would like to do a pin-out test before I pull the tank (or the bed). The pump will not run/prime in KOEO test, the relay is good, as are all of the fuses and the inertia switch.
Looking for a wiring diagram handy for this purpose? I've look all over this forum and searched quite extensively and I haven't found one for this year. Since it isn't my truck, I don't feel like purchasing a manual. I'm working on a 2003 3.0 2WD Auto.
If a wiring diagram isn't available, what colors are the wires going to the fuel pump? That way I can at least test the ground and the positive.
Got a 2002 7.3 f550 and the other morning it wouldn't go into high idle. Noticed my parking brake light was off. Messed with the switch and eventually jumped straight from the connector to ground... still no light. The light does illuminate with key on. I have tested the fuses. Where do I go from here? Looking for a wiring diagram....
View 14 RepliesAny pic or wiring diagram of the starter relay that is mounted to the fender. I'm trying to start the truck finally but it's just cranking and I think I might have mixed up the wiring. Is there supposed to be a constant hot at the glow plug relay when the ignition is off?
View 14 RepliesI have a new to me 1999 F250 with the 7.3 engine. The previous owner installed a push button start to get around the ignition actuator being broke. Over the weekend I pulled the column and replaced the actuator but the truck will still not start with the key; with the push button it starts just fine. I'm not getting any power on the starter relay signal wire, so I suspect something in between the key and starter relay. I searched around a bit, but could not find a wiring diagram for a 1999 diesel super duty.
View 3 RepliesAny COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesLooking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesLooking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 RepliesI am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 Replies