Ford F-150 - 1997-2003 :: P0308 Cylinder 8 Misfire Detected
Jul 11, 2015
Where do I start? Pull the coil?
View 5 Replies
Jul 11, 2015
Advertisement
Ford 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesFord F-150 (2004-2008) :: Code P0308 Read Out Misfire On Cylinder 8
Started as I was warming up the truck,a slight vibration/shudder. First thing that came to mind was F150. Torqued words of wisdom that it might come back, I had a p0301 before. Had no CEL, so decided to drive it to see if it got worse. Turned onto the main road and on came the CEL. Pulled into my FORD dealer, told him about my problem. Code P0308 misfire on #8cylinder was the read out, COP was done and the plug. 40 min of labor. She's even quieter than when #1 got changed.
View 3 RepliesLexus SC430 :: Misfire At Cylinder 8 - Error Code P0308
The car has an obvious misfire and the scanner says its Cyl # 8. I tried the "italian" tune-up and under heavy throttle the miss goes away. I swapped coils and the miss stays with Cyl # 8. I pulled the injector, and can't see anything wrong.
View 11 RepliesElantra XD (2001-06) :: 2003 - Code P0303 Misfire Detected On Cylinder 3
2003 hyundai accentra and I have trouble code P0303 misfire detected cylinder 3 the car would run rough and hesitate at idle and run rough in drive and reverse I checked the plug gap on number 3 cylinder and it was excessive so I regapped it and put back and the car run good for about a day and now the engine light is back and is running rough and hesitating.
View 1 RepliesFord F-150 - 1997-2003 :: Error Codes - Misfire Detected On Cylinders 2 / 5 And 6
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
Ford - Taurus :: CEL Came On With P305 Code / Cylinder 5 Misfire Detected
Wife's car - 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". The car had been running rough. I changed the plugs, wires and coil. After changing these (and clearing the code) the car seemed to run better for about a week. Today it suddenly started running rough again and the CEL came on with the same code. I'm guessing now this is probably fuel related as opposed to spark related??? As a side comment, the tachometer has been fluctuating as of late as well (again, intermittently).
View 5 RepliesFord - Taurus :: 2005 Started Running Rough - CEL Came On / Cylinder 5 Misfire Detected
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 RepliesFord F-150 - 1997-2003 :: Misfire On 7 Cylinder
I have changed the COP and the injector as well as the spark plug. I am still having a misfire on #7 cylinder....
View 8 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Random Misfire Detected On Cylinder 7
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
Passat (B5) :: Random / Multiple Cylinder Misfire Detected
What is going on with my sisters passat 2002 V6 GLX Auto 4Motion. Here is the codes:
16730-Camshaft Position Sensor (G163) Implausible Signal
P0346-35-00
16684-Random/Multiple Cylinder Misfire Detected
P0300-35-00
16688-Cylinder 4: Misfire Detected
P0304-35-00
16690- Cylinder 6: Misfire Detected
P0306-35-00
16689-Cylinder 5: Misfire Detected
P0305-35-00
I changed Both sensors and it still same problem. Car only has 40,000 miles didnt change timing belt.
Passat (B6) :: Random / Multiple Cylinder Misfire Detected?
my car was running fine yesterday. Today the check engine light came on and it started to run funny.. I checked the diagnostic code and it says the the cylinder is misfiring and that oxsygun sensor is malfunctioning. (Random/Multiple Cylinder Misfire Detected)
View 4 RepliesFord F-150 - 1997-2003 :: Unexplained Misfire On Cylinder 1 And 5
My truck has developed a misfire on cylinders 1 and 5. The OBD2 scanner at autozone says code P0300, Po301 and P0305. I bought a new set of plugs and wires. Problem still there. I then replaced the both coils. Problem is still there. Is there a control module or something that could kill those 2 cylinders like on the older trucks with distributors?
View 7 RepliesFord F-150 - 1997-2003 :: Engine Misfire On Cylinder 4 And 6
I have 97 150 it has a misfire on cylinder 4 and 6. I put new coil packs on and new plug wires. Spark plugs are only a year old. what else it could be?
View 1 RepliesFord F-150 - 1997-2003 :: 2001 - Misfire On Cylinder 6 - CEL On?
I have an 01 5.4 Triton with engine light on I put it on the scanner and it read miss fire on cylinder 6 and 1 I changed the cops and plugs boots and spring erased the codes but the check light is back on and scanner is say miss fire on same two cylinders u can hear it in the exhaust u can smell gas when sitting at an idle around 40 MPH has a slight engine shake goes away when u accelerate I am not sure what else to do some one told me to check for vac leaks and fuel pressure.
View 14 RepliesAccent MC (2006-11) :: Random / Multiple Cylinder Misfire Detected
I guess misfires are a rite of passage for these vehicles. I purchased it only a week ago. Welcome to Hyundai...
The car has 53k kms. It's throwing P0300 and P030X on all cylinders. There was one instance of P0128. The engine runs smoothly and doesn't seem to down on power, although I have nothing to compare it to. The only performance issue is that it acts as if there is a rev limiter at 6k rpm. It sputters and stops pulling above 6k. Strangely, it doesn't throw the codes under load. The light flashes while it's running steady-state.
I pulled the plugs and they appeared to be in excellent condition with no erosion of the electrodes. The ash is slightly more white than I would expect, making me wonder about it being excessively lean. I called the dealer. They told me that coils are problematic. Replacing the coils made no difference.
That lead me here. I found the thread "Check engine light flashes then stays solid," which referenced the ECM update.
Interestingly, of the codes mentioned on the TSB, the car is having all but the last two.
- P0300: Random/Multiple Cylinder Misfire Detected.
- P0301: Cylinder 1 - Misfire Detected.
- P0302: Cylinder 2 - Misfire Detected.
- P0303: Cylinder 3 - Misfire Detected.
- P0304: Cylinder 4 - Misfire Detected.
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature).
- P0328: Knock Sensor 1 Circuit High Input.
- P0461: Fuel Level Sensor A Circuit Range/Performance.
Tiguan :: 2010 - Random / Multiple Cylinder Misfire Detected - MIL On
My buddy has a 2010 tiguan and hes having a misfire issue. It has a hesitation and the interior lights seem to dim with the hesitation. Heres the codes that pulled up with vagcom.
4 Faults Found:
000768 - Random/Multiple Cylinder Misfire Detected
P0300 - 000 - - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 148426 km
[Code] ....
What it might be?
Ford F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.
Ford F-150 - 1997-2003 :: 1999 - Persistent Misfire In Cylinder 5
I have a 1999 F-150 4.2L with a misfire in #5 cylinder. I have replaced plugs, plug wires and coil pack, checked compression (147 psi) and ran 4 cans of seafoam thru it and still getting misfires on acceleration. It'a a 5 speed and it sounds rough and runs a lil rough as I go thru the first 3 gears, then it runs good as I get up to speed and cruises fine at 80mph. I'm thinking a bad fuel injector???
View 7 RepliesFord F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
Ford F-150 - 1997-2003 :: Misfire On Cylinder 8 Usually In Mornings Or If There Was Moisture In Air
I have a 2000 4.6 2wd f 150 ext cab. I started to have a misfire problem on cylinder 8 every so often usually in the mornings or if there was moisture in the air. It gradually got worse over time and when I got it read it had gone to cylinders 5,7, and 8 with the misfire codes which said misfire cylinder whichever primary/secondary circuit misfire and it has now gone to cylinder 2 as well. I replaced all the coils and the plugs with autolite platinum plugs and new coils for this motor and the problem has not changed. It came right back after I cleared the codes, what possible causes I could check out....
View 9 Replies