Ford F-150 - 1997-2003 :: Oil Light Came On Made A Knocking Noise And Shut Off
Nov 24, 2014
I have had a noise in the front of the engine of my 2002 f150 4.6 for about 2 weeks. On my way home my oil light came on made a knocking noise and shut off. The engine would not start back starter would engage but not turn motor it was seized. i called a tow truck and had it towed home. The next day just out of curiosity I tried to start it. It fired up ran and built oil pressure. If the oil pump froze will that make it . Can the oil pump make the engine act seized up?
View 3 Replies
Advertisement
2001 F-150 4.2L automatic, 189k mikes. Gas pedal would do weird knocking/vibrating. It would do it at idle & under acceleration. Gas pedal would knock & sometimes slightly move or kick back at you. Felt like someone was lightly hitting it with a small hammer. Well there is not much to the gas pedal assembly; pedal, throttle cable & mounting bolts/plate. Looking under hood, a bracket from drivers side of motor was pushing back against firewall, which was pushing into gas pedal mounting bolts. I grabbed the bracket & it came off motor. Nothing else attached to bracket. Looks like it rusted off and was pinned between motor & firewall. Well, this fixed the gas pedal problems. But now i wonder what the bracket is & whats it suppose to hold??
View 3 Replies
My brother's truck is a 2001 reg cab manual 4x4 with 4.6 and auto tans. Truck has roughly 130 i believe on it, this mornig he had blower on high in defrost position about three miles from leaving his apartment he said he heard a POP and the blower quit. No burnt smells or anything he said. SO Im gonna check the fuse first after that what should i do? Is there a relay for the blower? And do the new trucks have a resister for the blower speeds? If so how do i check these parts?
View 1 Replies
I have a 2001 F150 4x4 4.6L Auto trans. 96,000 miles... I purchased it in Jan with 93,000. About a month ago it started making and occasional knocking noise coming from the engine, this noise was heard at idle in park and in drive. when I revved the motor it would go away but as the idle settle back down you could hear it again. the noise would go away as I was driving and come back with no rhyme or reason, I put a stethoscope on the engine and it seemed loudest under the oil pan. The oil gauge is up between 5/8 to 3/4. Fast forward to now, When I start it I hear a scraping almost grinding noise that resonated thru the cab it has the same intermittent characteristics. I think I am going to remove the serp belt, remove the trans inspection cover next and see what happens. Oh I did put a scan too on it, no codes but did notice 1 long term 02 sensor trim was staying around -.618 if I remember.
View 11 Replies
The last couple days my truck (1997 f150 4.6l) has been having starting issues. At first it would just turn over and not start then the battery would die. So i bought a new battery and yesterday now its starts sometimes but when trying to start it while its ttuning over it stops then starts turning and starts up. Then i drive wherever I am going when i get back in to start there's nothing.
Its not turning over at all but when i turn the key there is a loud single knocking noise coming from behind the dash near the passenger floor vent. Actually there ate two noise from the same area, one when i initially trun the key and another when i release the key. But after just sitting there doing this it will finally turn over and start. What this is, there are no codes being thrown besides my dreaded P0401 which i cant seem to get rid of either. Ive changed every part that has to do with the egr system and cleaned the throttle body replaced vacuum lines and still the code.
View 14 Replies
I bought a 01 F150 with the 5.4 motor in it not much over a year ago. The truck needed quite a few things but the price was right. I have been dreading fixing one issue I knew about when I bought the truck. I figured I would ask here before contemplating taking my 12 year old truck to ford.
I have done quite a bit of reading about the airbag codes and in some cases people suggested the passenger switch led can burn out causing the light to occur. Here's what I know,
The truck has not been in a accident. I bought it from the owners son who only knew where to put gas in the truck. The father took care of the truck and he assured me it was not accident related for what it's worth.
Upon start up there are no flashes of the airbag light. From the time the key is turned ign. on to the time I shut the truck off it is a solid light. Early this spring I soldered a new led in the passenger on/ off switch with no change. I wonder if the switch is bad but I did not see a proper way to test it.
A airbag light code reader would seem to possibility but I have not seen any auto-part stores that borrow that type and my obd2 scanner cannot pull those codes. Where to start with troubleshooting?
View 3 Replies
The EMS service in the county next to ours lost one of it's new trucks for a few days on Tuesday. While going on a call, the engine made a tapping sound for only a few seconds, then a loud pop and shut off. Ford dealer went and picked it up and took it in for evaluation. VERDICT: Broken rod and cracked block. I have to say, this is the first I've heard of a 6.7L having a problem like this in our area.
Ford was really interested in this engine, as a new one is already on the way and the old one is to be shipped back for complete breakdown. So far, the Director and County Manager have been impressed with Ford's response to this problem. Dealer has told them the truck should be ready by the middle to end of next week. If I hear anything else, I will let you know. Any engine can break at any time, I'm just glad they are moving quickly to rectify the situation.
View 14 Replies
My 2001 f150 is having a issue with the dome light. Sometimes when I park with the truck leaning to the right the dome light won't shut off when closing the door. What is the name of the switch that shuts the dome off? I assume it is located behind the kick panel.
View 1 Replies
I have been getting some knocking the under most any loads . I do not have any codes. I tried premium gas and that did not make any difference. If this is not fixed what issues can this cause? What should I look for do get this fixed?
View 14 Replies
My 2000 F150 started knocking, it does this after I get up to speed and let off the gas a bit, it will know as I push on the gas again but if I push heavy on the gas it dose not knock, What could if be? By the way it is a hard knock not a pinging sound.
View 3 Replies
My 2003 F-150 knocks pretty bad on my early morning cold start ups. It only happens if it had set for a while. Its not a knock coming from the bottom end it sounds like its coming from the top end, cams cam followers... etc. I was wondering if I should be concerned. I am running 5-20 mobil 1 with a motorcraft filter. My truck always seems to use a half a quart to a quart between oil changes too. The truck only has 60,000 pretty mild miles on it.
View 14 Replies
I have a 2001 F150 4x4 5.4l with 105k miles. I started it up today to go to lunch and it made a knocking sound on start up that lasted maybe 20 seconds. So i shut it off and checked oil. All ok. Started it up again and it knocked but not as long as it did previously. I started to drive and higher in the rpm range before the trans shifts it makes the same knocking sound. Left off the pedal it goes away then rev it again it doesn't make the knock till around 2000rpm mark it I remember correctly. It makes the noise in all gears, parked or driving. It runs great, no power loss or misfire. Could it be a spark plug on the verge of blowing out or is it time for a new motor? I am going to look at it more tonight when I get off work.
View 2 Replies
The other day I was driving down the freeway... My F150's heart started knocking... I am thinking of rebuilding it or I was thinking if I can find a good priced lightning 5.4 going with a swap.. If I did go with a swap what all would I need from the donor truck? I am guessing a rebuild would cost me around $2000.. Since I don't have the know how or the place to tempt it on my own.
View 3 Replies
New to owing a ford pickup. I bought a 2002 Ford F-150 lariat 4x4 as a project truck. I've always wanted a truck to mess around with, but once I got the truck home I noticed it had a knocking sound. It didn't sound like it came from the top of the engine so I checked the muffler first and found it had a 3" slit in it. I replaced it but the sound remains. I heard it could be lifters? Is that something I should mess with or not?
View 8 Replies
I am going to start from the beginning because oftens times we don't provide all of the information that may be pertinent to the correct diagnosis or repair. It'll be kind of lengthy! It all started about 3 days ago when my wife told me that my truck was "shaking." I said, "ok, just drive the car til' I can look at it" The next morning, the I was able to look at the truck. I had a cylinder 8 misfire detected. I drove it for about 1 hour that day to and from work. I did this so I could see what what the "shaking" was. It was actually what I describe as a "shudder."
Anyways, I done a fuel pressure check and all was well. I took of the coil, tested it, it was fine. So, I took out the plug to inspect it. It was wet! Not drinched, just mildly damp. I dried it off, cleaned it off with carb cleaner and it fired right up no hesitation no nothing. No CEL light, no shaking, no shuddering. It ran perfectly normal. I let it warm up to speed and took it for a test drive around about 6 city blocks. All was well. So I took it on the highway for about a 2 mile stretch. I was givin' her some juice pretty hard to see if it would misfire. Upon acceleration I heard a screech. Now this is where it get's interesting.
The screech that I hear, I just related it to the belt because it's done it ALL the time. When I first bought the truck it squalled like a whipped puppy cause of a cheap belt. The good ol' bar of soap trick fixed that! But, ever since then, it upon shifting, or under acceleration it would screech then stop. So anyways, on the highway run, it screeched while I was accelerating. It did this from about 60mph-80mph. I then, turned around and came back home. By the time I got to the stoplight to turn off towards my house my oil light was on and the engine was knocking. Not a tap, a knock.
I slowly coasted home not going over 20mph and pulling it out of drive as much as I could. I get home, and I check the oil and there is nothing on the dipstick! WTF!? I always run Mobil1 Full synthetic and put it 6qts. It doesn't smoke, doesn't leak or nothing! So I freaked out and went and bought 2 qts of Valvoline Hi-Mi and poured it in. It brought up the hash marks and quieted the deep knock. Later that night after work, I done a full oil change and flush and put back in my Mobil1 Fully synthetic 5w20. It now knocks at startup, and smooths out to a tic. Then at idle, it sounds like a light knock. It appears that it goes away upon acceleration.
View 14 Replies
The knocking started very suddenly 2 days ago - but not after any unusual events, other work etc. Truck has 145 K, and otherwise starts & runs perfectly. Doesn't use oil.
I heard it from in the cab, windows closed. At first, thought it may be a rod bearing - but if so, not terribly loud. Didn't drive it any more after getting home. But starting it in the drive, the knocking was audible.
Then I discovered it * completely disappeared * several times, after shutting off engine, then restart a few seconds later. When that happens, absolutely no knocking at idle or reeving it up a bit. But it may return on the next 1 or 2 restarts, then disappear again.
Since the knocking * completely stopped * on some restarts, does that rule out a bad rod or main bearing?
I haven't seen oil gauge pressure fluctuation, whether it's knocking or not. The gauge is where it's always been - well above 1/2 way. But, the gauge also doesn't move when I rev it to around 2000 RPM (? may be normal not to move, after engine's already running?). When the knocking is happening, increasing RPMs also increases the knocking frequency.
Can't hear the knocking from top side of engine w/ hood open - even using rubber hose to my ear & moving it around. But (when) it knocks, can easily hear it inside the cab or under the truck.
From underneath, knocking is more in the center of truck, near the back of block / oil pan or tranny bell housing. I can't isolate the noise as more on one side of the block than the other.
Could the oil pump itself be making a knocking noise? The knocking is "similar to" a rod knocking, but doesn't seem quite as "hammer on metal" metallic.
There are no DTCs showing on my scanner. Only odd thing was, for "O2 Monitor Test," it showed "vehicle did not return data for any O2 monitor test." Though under the scanner "I/M Monitors," it shows O2 Sens Mon. "OK," and O2 Sens Htr "OK."
View 2 Replies
I have a 97 7.3 ... I've had it about 2 months now and now it wont start! It will start and idle for 2 seconds then start knocking and die! I had a buzz test ran on it and all is good. I also checked my Icp and checked my uvch harness with my multimeter. Before this it would run ok but seemed like it had a miss and a lack of power. On start up if i didn't have it plugged in it would smoke white smoke horribly. I am thinking maybe my IDM. I need my truck for work .... I had it hooked up to a scanner and it said faulty IDM.
View 1 Replies
I have a 2003 F-150 4.6 4X4. I had a knocking sound that sounded like a rod knocking but was coming from the bell housing. After some research, I found that it could be a cracked flex plate or bad torque converter. I bought and installed a new torque converter with no change. The flex plate didn't appear to have any damage but went ahead and replaced it with the same results. I actually started the engine by jumping the starter (with no transmission) and the sound was coming from the flex plate/dust cover. My question is do I need the dust cover? Or is it a bearing or something else inside the engine causing the flex plate to hit the dust cover?
View 3 Replies
2003 F-150 v8 4.2 4x4 with 295k miles ...
Yesterday while driving in town going 35-40mph my F-150 gauges spiked just before the engine shut off. While still moving I shifted to neutral and tried to restart, no go so I was able to stir to the shoulder and park, turned the key off. Sat there for about 30-60 seconds and the truck started up and I was able to drive off. [added] Forgot to mention, there was no check engine lights or anything, when I drove off, it was as though nothing happened. Not sure if it matters but temps out here was about 105 degrees and I was blasting the AC (which seems to take longer now to cool things down a bit).
I've had the truck since '04 and the second owner, been pretty descent with fluid changes and such, in fact was on my way for quick oil change when this happened. The tech there thought it could be either the alternator (battery is roughly 6 months new) or the ECM.
View 10 Replies
I have a 2001 Ford F150 4.6 liter V8 Super Crew. I use Castrol full synthetic oil and Fram filters...changing oil about every 10,000-12,000 miles and change filter at half way point.
Here is my issue: I noticed a slight rattle on passenger side of engine a few weeks ago but engine ran well & I wasn't sure if it may be a pulley from AC compressor or something else. It wasn't bad at all...more like a ticking sound.
Yesterday I drove to work with no problem and when I got ready to leave 9 hrs later, I noticed rattling was getting worse. I ran about 2 or 3 miles down the road and my oil pressure flatlined and light came on. This is the 1st time it has ever happened. By this time the rattling sounded bad, almost like it broke something on both sides of engine around valve cover area.
I pulled over immediately and had truck towed to shop down the road from my house, When my mechanic started it up this morning it had oil pressure and rattling was not near as bad. I put a new oil filter on it & topped off oil. He could not get to it today so I drove it home today for the weekend and by the time I got home (3 miles) it did same thing...flatline, oil pressure light on and rattling with no power (very sluggish).
I did notice the oil pressure light came off & on and gauge went up and down a couple of times before I shut it down. What the problem is? Oil pump maybe? I just didn't think oil pumps usually fail.
View 7 Replies
My '02 F150 180k X-cab with the 5.4L is leaking coolant when it is shut off. Its just pouring right out.It looks like it's coming from top of the trans and around the firewall area. I had to replace a drain plug already.. the one behind starter ..its not leaking.
View 4 Replies
