Ford F-150 - 1997-2003 :: Odometer Quits Sometimes / Transmission Skids Loudly / Gear Shift Lever Sloppy
Oct 5, 2014
The Speed Needle works fine. But...the Odometer part quit some time ago. I can't tell what my fuel Mileage is now. How to troubleshoot this problem?
Things that might affect this problem; Transmission skids loudly when going in and out of 4-OD. It could be the Torque converter clutch?
The Gear shift lever is sloppy. Doesn't fill me with Confidence.
Brake fluid warning light is on most of the time. Fluid level is up hi though. Driver door mirror control switch don't work in one direction Who on this Forum has a Switch for me?
View 14 Replies
Advertisement
I just bought a f150 2001 5.4L crew cab. It has the O/D switch in the gear shift lever and the black plastic handle is broke. I found a complete replacement lever on ebay but cannot find any tutorials on how to replace this.
View 8 Replies
1997 F150 xlt 4x4 ... When I shift the gear shift lever to below D (2-1) it blows a fuse and I lose instruments. Replacing the fuse is not difficult, just tiresome..
View 6 Replies
I have a 96 ranger 4.0L shift lever was very sloppy and one of the torq bolt fell on the floor I used loc tite and tightened them up with no problem put everything back together and now it wont start. I think I checked everything even replaced the neutral safety switch, adjusted the tranny cable, checked fuses and switched around the relays maybe an ignition switch? I am running out of stuff to troubleshoot.
View 13 Replies
Volvo Automatic 1992 240 - So, just started to back out of the garage and, all of a sudden, my gear shift got stuck in neutral and then started shifting without engaging the transmission at all. Pushed it back into the space and, taking a look underneath, I realize the control rod's completely detached from the lever in the transmission.
I can re-attach it, but it just comes loose again when I shift. It seems like something should be in there to hold the control rod in place with the transmission lever, but I don't know what because I can't seem to find any documentation on what everything should look like down there.
Attaching a couple shots, one with a circle around the area that's coming un-attached since the angle's a bit off.
Attached File(s)
IMG_8972.jpg ( 1.09MB )
IMG_8978.jpg ( 938.64K )
View 1 Replies
So I drive a 19 97 F150 v8 5.4 4x4 and while on the freeway I noticed that my overdrive button was blinking on the shift lever. The truck wasn't driving any different than usual, so Im just trying to figure out what this means.
View 1 Replies
4x4 wont work, when I shift the lever on the floor it doesn't engage so i bought two new solenoids.. didn't work, have power on both solenoid connections. If I unhook my vacuum lines from the solenoid, I can push the Actuator rod in making my 4x4 work. I've gone threw everything.. have vacuum, have power on my solenoids. Just nothing works when I shift into 4x4 on the floor.
View 3 Replies
I have a 1997 f150 4.6L 4x4 Standard Transmission and today I hopped in it to go to work, and the Speedo, Trip Odometer, and Odometer all are not working.
This is the first time it has happened to me, what could cause this or have a problem similar to this and know how to fix it?
View 4 Replies
I've been experiencing the ever so popular sloppy shifter lever in my 02 excursion. So naturally I started prowling around the site looking for answers to my issues. I have ensured both of the torx bolts are present and tight at the end of the shift tube on the bracket that connects to the shifter cable and have replaced the shift tube (It was worn out) and it worked great but has not completely fixed the issue so today I crawled underneath the truck to try and adjust the shift cable and have found that the detent in the shift linkage from the gear position sensor that runs to the shift mechanism (not sure what it's called) that is inside the transmission is really nonexistent, it is effortless to move it from P to R but from R to N is good and stiff like it should be but from N to D and D to 2 is effortless. I have zero experience with what creates the detent inside of the transmission and looking for a link or pictures or write up something that I can look over and attempt to educate myself on before I dive in to this blind....
View 14 Replies
As it turns out, my shift cable wasn't bad. The transmission lever coming out of the transmission doesn't want to move very easily. When in gear, it shifts fine as it should, so I'm thinking something is bad with the lever. Problem is, I don't know what could possibly be causing it.
View 8 Replies
72 Ford F250 with big block 460. after three years my truck is ready to run as soon as i get my new fuel pump in today. was hooking up shift linkage and noticed the shift lever will only click back two times and then goes all the way forward. I put a shift kit in the c6 and it was beautiful condition inside cant figure out why it would only shift to two places.
View 2 Replies
I recently bought my first EX and I finally had enough of looking at this
The transmission shift lever indicator not being in the proper position needed to be fixed!
After some searching, I realized what the issue was and was quite surprised that the "fix" is replacing the entire shift lever indicator assembly. Seems overkill but right on par of with the way the world works nowadays.
The other solution I found was by a company called Dorman. They make a Shift Indicator Cable Bracket, which is the only part that was damaged in my case as you can see here. The white part pointed at by the arrow is supposed to be attached to the rest of the white plastic.
I looked around the garage thinking I need some glue. And something to reinforce the freshly glued parts. That should have been much more difficult as I don't regularly fix tiny plastic parts BUT I quickly came across this old external hard drive cover.
Broke some tabs off, trimmed them to size and poured glue all over the place.
This is what I ended up with.
Now my OCD can focus on something else
View 2 Replies
I have a 1991 Aerostar 2wd 3.0. I recently had freeze plugs replaced and the mechanic had to drop the tranny to get to some. Now the shift cable has come off the gear selector lever. I have googled everywhere and can't locate the procedure for reattaching it. My mechanic was doing the work on the side and charged me only labor for his assistant. He is at work right now..
View 5 Replies
I think the gear shift lever is loose and so I get a no start every day or two. I remembered seeing somewhere here that there was a way to tighten up the grearshift lever to fix this problem. I did a search to no avail.
View 5 Replies
I have a 2001 Ford F-150 5.4L Supercrew that won't seem to shift out of 1st gear. This morning coming out of stop light on the way to work, the truck seemed to jerk when it was supposed to shift into 2nd gear. I was told by a friend that the speed sensor may be it?
So I took the truck around the block just so I can get a feel for what is going on. So the truck shifts into 2nd, but not past that. It seems that around 30mph the RPM's go up jump up quickly to 2k+ and no shift or increase in speed. I was reading up a bit on it and came across the possibility of a TPS?
View 5 Replies
In 30 years of wrenching on cars, I've never encountered this problem. Replaced the pads and left rotor. Rotor is typical Chinese rotor. While there, replaced the wheel bearings. Also knocked out the races (with a brass drift) and replaced the races with the ones that came with the new wheel bearings. The bearings are NAPA bearings. Packed the wheel bearings just like always.
Applied some grease just like always on the spindle. Put it all back together. Tightened the wheel bearing nut while rotating the rotor in the opposite direction. Went to maybe 10 ft lbs. Backed the nut off, set it firm finger tight. Installed the cotter pin. Got a whole bunch of sloppiness in the wheel bearings. I can feel a LOT of it when rotating from the 6 o clock and 12 o clock position. What did I miss? NEVER had this happen before. 2002 f 150 2wd
View 3 Replies
Having trouble with shifter not going into park. The linkage is sloppy. Is there a bushing kit or something to tighten up the linkage?
View 3 Replies
I have a 1999 ford f150 v6 no 4x4 has wont shift from 2nd to 3rd, shifts fine from 1st to 2nd, after that tho there's nothing. What to do or what it could b?
View 1 Replies
I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
View 7 Replies
Transmission problem, will not shift lever. If car moves while on P, then the interlock will not disengage. I car doesnt roll at all it will allow me to shift gears but if the cars rolls just one inch then i cant shift gears. Already replace brake sensor.
View 6 Replies
I have a 2012 Elantra Limited with about 36000 Miles. I purchased this car used with 12000 miles. I commute to work about 90 miles round trip a day mostly highway. I usually average about 33 or 34mpg. Recently, my mileage has fallen to 22 or 23 mpg and I have noticed my car having problems shifting. When accelerating normally, 1st - 3rd shift normally. Once I get into 4th, the car won't shift into 5th unless I manually do it with the gear lever or play with the throttle. If I just accelerate it will go all the way up to over 6000 rpm before it will shift. There are no problems with down shifting. Once it gets into 5th it will shift into 6th normally. There are not warning lights on and it doesn't always do it so of course when I need to recreate it I can't.
View 26 Replies
