Ford F-150 - 1997-2003 :: Odd Shifting - Getting 1st Gear When Put It In Reverse
May 26, 2012
In my 1998 f150 4.6L 5 speed manual. When I go to put it in reverse I get 1st instead, but if I do a second shift to reverse I get reverse. This happens on an average of once a week.
I know this can happen in FWD cars where you put it in one gear and get a different gear instead. Something to do with the shifting cable. But the f150 is RWD, the shifting problem only happens in reverse. Is this problem someone without ASE certificates can do, or without dropping the transmission?
I'll add to this so I don't start yet another post. Ive thought of the problem and if it was really going into 1st instead of reverse the problem likely would be bad enough it would just stay in 1st. Its possible that I am getting 4th gear when I go into reverse which tells me the clutch grabs really well, and its a problem I really need to fix, I don't know that much about transmissions but I do know if it keeps getting 4th instead of reverse, the clutch wont be so good pretty fast.
View 1 Replies
Advertisement
Just got a 98 f150 yesterday and I noticed last night when I went to shift into reverse, with the clutch all the way to the floor as I tried pulling the shifter back, it sounded like the clutch wasn't engaged at all. Shifting from all the other gears works just fine. Ive found that If the truck is off and I start it in reverse it works just fine.
View 3 Replies
I have a 03 f150 2wd with the 4.6l. Recently it has been slow shifting into reverse(about 2 full seconds) and when it finally gets in reverse it shudders when it comes under load. The fluid is full and not burnt...
View 1 Replies
My daughter bought this truck about 6 months ago. This morning a driver cut her off, then hit his breaks. She had to make a panic stop. When she went to take off again, 1st and 2nd was no problem. When she shifted into 3rd, the engine just revved.
She tried to shift back into 2nd, but it wouldn't go into 2nd. She pulled over and now it won't go into any gear. The shifter lever won't even go over far enough to go into 4th, 5th, or reverse. I doubt the panic stop had anything to with it, but thought I'd throw it out there, just because.
Okay here's the truck: 1997 F150, 4x4, base model, short bed, 4.6L, 5 speed manual, manual transfer case, 190k miles. Truck has been beaten and abused badly, but is basically mechanically sound.
Here's what I've done so far. Checked the fluid, it was fine. Pulled the top cover and shifter lever out. I don't have a clue what I was looking for in there, but I hoped to see something obvious. I didn't.
View 13 Replies
A few weeks ago I bot this truck to have some fun with. 98 F150 4.2l with a lift and some beefy tires. Well something to get me into trouble. On the test drive i never herd anything, mostly because I wasn't ripping it around. I know very little about transmissions, mostly because I never had a problem before.
I have a grinding noise when down shifting into 3rd for either 4 or 5th. It doesn't happen when I am going from 2-3. It also wont happen if i keep the clutch disengaged for a few seconds. It almost like the transmission need time to slow down for a second before shifting.
It also does this going into reverse.
View 1 Replies
I have a 2000 F150 with the 4.6L engine and I have a question about the transmission. When shifting from 1st to 2nd gear there is sometimes a little hard jump when shifting. All the other shifting through out the range is buttery smooth. The issue has been around for a long time and has never gotten worse. Is there anything simple I can do to fix this. Do those tranny additives work at all? Otherwise, I will just continue to live with it.
View 2 Replies
I have a M5OD that I replaced the clutch in in my '99 150 4wd in December . Manual Tranny. Now when taking off in 1st gear the transmission seems to be sliding or shifting backwards, but only in first gear. Got under my truck and looked, can't find any identifying marks to where it might be moving or what is causing this. All frame mounts are tight and the bell housing is flush with the motor. Yes, i did do the clutch change myself in shop class.
View 1 Replies
So my aunt has a 2002 ford f150 king ranch 5.4l and a night ago it started this problem which when you put it in drive which she has to put it in 2nd for it when she pushs on the pedal it will rev up to 2500rpms than jerks and goes and its usely fine till she stops than goes and it does it again...
Than today it wouldn't even go in anything but reverse... So than we herd about the Range Sensor on the side of the transmission and it seems like it was it so I unplug it when it was running and when i push on the pedal and it revs up to 2500rpms it will go forward and have power. So we went to get a new range sensor after like 4 hours trying to get the dam thing off and another 2 to get it back on.. I started it up and only reverse works again... So I unplug the harness to it again and we got the gears but 1st and 2nd will just rev and go.
We at a lost right now i even tighten the shift screws under the dash cause our expedition was loose at one time and the gear shifter was loose like hers. But even tighten the bolts it still don't fix the looseness or even the gears.. Is this a transmission problem? OR even the torq covertor?
View 4 Replies
I have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 Replies
I have a 2000 F-550 w/7.3 and a 6 speed ZF transmission. My problem is that when you go to shift into any gear inc. reverse the transmission stays in 5th gear. I pulled the shifter and tried to do it from top of transmission it still stays in 5th. Any thoughts that I could possibly check?
View 1 Replies
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
View 1 Replies
Took my car in for oil/filter change and in some odd circumstance, the young mechanic managed to drain 1 liter of transmission oil out of my car (which I didn't know at the time). After driving for 10 minutes (~5 km), I noticed my reverse gear wasn't shifting properly. After ~30 minutes of driving, my car was smoking from the exhaust pipe (turns out he had overfilled my engine oil too!!). Took the car back in to complain the mechanic supervisor claims my transmission is still fine and all I need to do is refill the lost fluid. Another independent mechanic later tells me my transmission line is likely fried if I had experienced what I did, and those guys should be responsible to replace everything. Since fluids have been topped up, I have no proof of who is right. So my question is, if I only drove for maximum 50 km after my transmission fluid was drained and engine oil overfilled, would that be enough to cause serious damage to the car?
View 10 Replies
Sometimes when putting the vehicle into first it's almost impossible to get it to go into gear. Sometimes it's super smooth. Also when putting into reverse we hear a loud clunk. That one is most of the time but sometimes it goes in smooth. I was doing some looking around at the pedals because I think I am going to have to replace my master cylinder and noticed that on the inside of the vehicle where the clutch master cylinder comes into the vehicle it's leaking black fluid. Does that automatically mean my clutch master cylinder needs to be changed? Could this be the cause of it being difficult to shift because the clutch isn't fully disengaging?
View 11 Replies
I'm having problems with my automatic transmission in a 2002 Saturn SL. About 2 months ago I noticed a delay when I would put my saturn in reverse and it would sort of kick into gear after a few seconds (up to 10seconds sometimes). I wasn't worried much about this at first until another problem started happening. Between second and third gear it seems to be shifting slow/hard(?). I can feel where it wants to shift, but its slow to shift and actual revs high before shifting down. The problem doesn't always exist, and some days its more then others. We took it to get a transmission fluid/filter change and this didn't solve the problem. Took it back for a transmission diagnositc and GM told us we need to replace the transmission or do an overhaul. They didn't explain why really though- no clear answer. I've heard everything from the torque converter to a solenoid problem.
View 3 Replies
I just had a 97 Ford Ranger with a 3 speed overdrive transmission in my garage that we replaced the transmission because it was not shifting down into first gear, not even manually!. The new transmission is doing the exact same thing as the original.
View 5 Replies
Lately I've had some issues with the indicator(the orange needle telling you what gear you're in). Often when I start my car, it would let me shift gears but the indicator would not move. I've never once had a problem shifting into whichever gear I want(knock on wood). Usually when this happened I would bring the gear selector back to park then try shifting it again. This would fix the issue and it would bring the indicator with it, but I knew I had to do something about it eventually.
Last night when I was on my way home, I started my car and shifted into reverse to back out. It didn't move the indicator, and nothing I could do(no back to park then trying again) would work. I eventually decided I'd just count gears to get home, then I'd have it looked at.
At home I decided to do some research as to find out the issue, and I thought I'd found it. I removed the panel under the steering wheel to look at the thumb-adjustment. Many posts I read said it's likely broken and I may need a new one (Or to fix it with zip-ties or glue). When I found it though it had not been broken. The white housing and the black wheel were both working fine, the wire doesn't seem cut. However when I put the parking brake on so I can shift gears and see what it's doing, the gear selector moves but the wire just acquires slack in it. It's still attached and I can't see a break in it anywhere, however it may be broken inside the jacket. I tried turning the black thumb-adjusting wheel both ways and got no success from that. It moved a little once but that was it.
The indicator needs to be replaced?
View 1 Replies
I really liked my 97 f150 4x4. It was a very very good truck... until last night. It randomly shifted into 4hi. Okay, shorted wires, right? Eh... well this morning i was gonna take it into the school's shop, and now its switching between 4hi and 4lo... on its own... so i disconnected the switch in hopes that that was borked and it still keeps doing it. Also, disconnected axle actuator and it didn't unlock so its sitting in the parking lot currently...
View 3 Replies
I have 1999, F150 5.4L with electric 4wd shift. I put it in 4high just fine and smooth. Now 4lo on other hand rough shift if it goes in 4lo, sometimes won't engage but 4 high works fine. What's the cause
View 2 Replies
I had recently purchased a 2003 golf gti AUTOMATIC (with optional shifter) with a 1.8 turbo 4 cylinder engine. The vehicle has 139,000 miles on it. Before purchasing, I had a mechanic come out and look at the vehicle for a pre-purchase inspection, and ran the code P0303 (cylinder 3 misfire) which without test driving, told me that is what caused the shift shudder I noticed when I had test driven it a previous day. He told me the coil packs were in good condition by looking at the top of them, and told me if I replace the spark plugs, the issue should go away.
I feel it is important to mention that he had also run codes on the transmission and nothing came up. Taking it home, this morning I had replaced the spark plugs and driven it for about an hour both regularly and aggressively to test it. The problem is still there, and I was really hoping that there is a solution to this problem, because everything else on the car is beautiful, while being my dream car, I just want it to work as well as I know it can. To be more descriptive, when shifting to 3rd the whole car feels basically like it is tripping over itself before successfully shifting.
View 10 Replies
I have a 1997 Chevy Blazer. I have had issues where I could not start my truck and determined it could be the battery. After checking alternator, battery, and starter I was told that all were good. Cleaning terminals did not fix problem. I got a new battery. So I have determined that a power drain is going on somewhere. I have now found that when I shift the transmission from drive to reverse or vice versa that the rear hatch window comes open. As I shift the gear I hear the latch popping behind me. Now I have determined that there is a short somewhere and this could be the cause of my power drain. What I need to know is where to start looking for the default and how to fix my problem.
View 3 Replies
I have a 1999 Ford F-150 XLT, with the 5.4 and a 4spd auto. 172,XXX miles on the clock and i have owned it starting on April of 2014.
Tonight driving home from work, it took some time on the highway (4 miles) to shift into top gear. When you lift off the gas pedal after reaching the speed limit, normally the truck will shift from 3rd to 4th no problem. When I let off the pedal, there was no gear change.
It took sometime for it to shift up. When downshifting on the exit ramp, there was nothing abnormal. Where I live it is 19 Degrees Fahrenheit and this is the beginning of the cold snap that will last well into mid-January of next year.
View 14 Replies
