Ford F-150 - 1997-2003 :: Noise In The Rear - ABS Ring On The Gear Completely Off
Feb 24, 2013
So I had the same , "noise" in the rear of my truck that i see other people having, at first I thought it was my tires, since I ran buckshots, so I switched over to street tires, and low and behold it sounded like I had buckshots still on the truck. So this thursday I pulled the diff cover off, and guess what i found!
The abs ring on the ring gear, was completely off , and the bolt that holds the pin for the spider gears was broken with just about maybe 3/8 to 5/16 of an inch left in the pin, right now i am still working on how to get that out of there.
also found a 1999 ford f150 2wd truck, 4.6 auto , that someone pulled a 1997 4.6 engine out of and put it in this truck and now it won't charge, and i think it's cause of the pcm needing to be reflashed. tested the alt, battery, everything is good, i just don't know if the pcm controls the charging system.
Pics will come soon of the differential destruction.
View 3 Replies
Advertisement
I'm replacing my rear diff cover and didn't realize there are multiple sizes. How do I figure out what the size is of my ring gear?
2001 F150 XLT 4x4 SuperCrew, 5.4L
View 3 Replies
I just came back from a long trip and during the 400 miles drive I started to hear noise coming from my differential - kind of like a constant high gear loud noise. I will hear this noise when I start to accelerate and it will only gets louder and louder as I go faster and faster. I had a pinion seal leaked fixed last week and I checked the fluid and it is full.
View 9 Replies
Just started. Replace fuel pimp and bracket 8 months ago. Now, three times in two days ...freely cranks, but does not fire. It has been suggested by a key man that my ignition key "Ring Transponder(??) is failing, about a $50.00 part.
Any links to a step-by-step to where I could do this myself? ($$$). I don't know what to call it, so it makes it hard to search online. the part he referred to in under my ignition switch shroud...but that"s all I know. (I was driving when I talked to him and forgot the exact term he used (I'm old, and easily confused by anything post ignition points and condenser)
View 4 Replies
Ok so I was going to just swap the whole rear end from drum to disk but it looked to be too much difficult;t. So the rear I have has 278,000 miles in it and its starting to make noise we were thinking about swapping the gear from the disk to the drum because the disk rear has 140,000 miles on it. Both have a limited slip. And 3.55 gears but i was thinking about getting 3.73.... So my question is can I swap in 3.73 gears into a rear end with the limited slip from one with 3.55 gears? Or do I need to buy a different limited slip?
View 7 Replies
I Just bought a 1997 Ford Explorer V6 4WD and I noticed after the I bought the truck that the whole rear suspension (Shocks) were completely destroyed. I failed to notice this during inspection of the car because it was parked very close to a wall so i was unable to see the area. Now I do know a bit a about cars but I no professional, It seems as if this whole section of the car just rotted out which is surprising because the rest of the car seemed OK. So now my question what do I need to buy in order to fix this I am not sure it seems like there is some sort of cross member that bolts onto the frame that connects the two rear shocks. What it looks like?
View 8 Replies
My 1997 4.0 Rear Wheel Drive is making a clicking noise when it is put into gear or when it switches from drive to reverse and vice versa. Sound is coming from the back of van. Does not make noise all the time. Drove 50 miles last night with no problems and minimal clicking. Could it be U-Joints going bad? Or is this a different problem?
View 6 Replies
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission. I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced. I have also just had a new hydraulic clutch kit installed.......
View 1 Replies
1997 F-150 XLT Extended cab. 4.6L VIN 6, 5 speed manual, 4x4. Replaced speed sensor on transfer case, speedometer is not completely dead but bounces around. Seems to be about 10 mph below actual speed. When I come to a stop say at a red light speedometer drops to zero at about 20 mph or so. Cruise also inop. It seems like whenever I let off the gas to stop or shift gears the speedometer drops down but then goes back up but not to the right speed. It has the mechanical odometer by the way. Everything else seems to be working fine. New speed sensor did not come with the plastic gear so I had to reuse the old one. Not sure if that gear was bad or not, but it was the pink one if that matters.
View 6 Replies
I have a 2001 ford f150 with a 4.6 liter v8, my ac compressor is completely seized up, I can't afford to replace the ac right now. So I would like to just get a shorter serpentine belt to bypass the ac for now, need to get a measurement on the shorter belt for my engine? and the proper way to re route the belt without the ac?
View 7 Replies
I have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 Replies
I have a 1999 F150 Supercab, 2wd. I just replaced the front rotors, calipers, and pads. Before I did this, the front right caliper was locking up completely. Now, after the new stuff is installed, the truck pulls very hard to the left when braking. The harder you brake, the harder it pulls left. What should I look at next?
View 2 Replies
2003 F150 4wd with auto climate control. My blower for heat and AC completely stopped working a few weeks ago. I have checked all fuses, i replaced the relay under the dash, i replaced the blower motor control module. I supplied power to the blower motor itself and it ran fine with no noises. I ran the self test on the controller in the dash under the radio and it passed. I am not sure what else to try.
View 7 Replies
2003 F150 SuperCrew 9.75". Today we got to tearing into my rear end on my truck. I was having a clicking noise from the rear end when slowing down from about 20mph. It was a constant click, click, click, click. It was driving me nuts. Well when I first tore the cover off to change the wheel bearings I found some metal pieces in the bottom of the rear end housing.
I did some researching and came to the conclusion it was the shims behind the side gears or the clutch packs. Well it turned out to be the clutch packs were totally shot!! The side gears and the spider gears were loose and kinda just flopping around!! I ended up changing the side gears and spiders gears, bought them as a kit through ford and then the clutch packs.
The job overall wasn't to hard at all. The hardest part was getting the spider gears spun into the carrier. Ford has a "special tool" that that compresses the clutches and another to hold the carrier through the splines in the gears so you can spin the carrier itself to spin the spider gears in. We ended up using the axel shaft itself and clamping it into a vise and setting the carrier on it to hold it from being able to spin.
We then took a piece of all thread and put it through the side gears and put washers on each of the side gears and nuts in-between them and then spinning the nuts up and down to compress the clutches. Basically what Fords "special tool" does. Then just spun the carrier with the pin that goes through the two spider gears and that was about it. Once we got that done it was all basically putting it all back together.
View 3 Replies
On my 01' the bottoms of the bump stops are completely gone. Rusted out to the point to where the rubber stop on the front lower control arm (if the truck bottomed-out) would go right thought it. The rubber stops are fine.
This pic was taken from below the control arm looking up. You see the rubber bumper and just above it is the stop (some what triangular shaped). the bottom is rotted away... Are these replaceable or repairable? They seem like they are welded to the frame.
View 5 Replies
I have a 1998 F-250 LD 4x4 with 462,000 km. I have been hearing for some time quite a drone coming from the rear axle. I am guessing the wheel bearings are due, as both front ones have been replaced, but never the rear. More about the noise, I hear it come to life as I gain speed. The faster, the louder. If I decelerate the noise is still present, but volume significantly decreases. Should I change the oil and friction modifier and see if there's an improvement or go ahead and change both bearings too?
View 7 Replies
2000 f150 182000 makes a rumbling noise from rear end mainly when turning at slow speeds. Thought it might of been axle bearings so replaced them this weekend to no avail. I have the 9.75 limited slip rear end but what I found out this weekend is that the axle bearings are for 8.8 , the 9.75 bearings was to big.
So does this mean I have 9.75 ring gear with 8.8 axles ? I have been using royal purple 75-140 with no friction modifier because royal purple says its it there.
But after doing some research Im going to go get some friction modifier and see if it works . So my question is how much of a pain is it to replace the clutch packs? What if I wanted to just put a different differential in and do away with limited slip ? Or go with a different aftermarket limited slip diff. ? what are my options , etc.
View 4 Replies
I have a 2001 ford truck and it makes a growling sound when i am turning right but is not when going straight ahead wondering what part in the rear end could be making this sound.
View 2 Replies
What size Ring Gear Diameter I have, 9.75" or 10.5"? Probably going to a 4:10 to get some power back after lifting my truck.
Current Axle Ratio: 3:55 LS
Bolt Count: 12
View 1 Replies
2001 F150--V8-4.6-3.55--8.8. 221000 Miles. Changed front rotors and pads. Had scrubbing noise from right rear when applying breaks heavily. Changed rear rotors and pads. Still have scrubbing noise when breaking hard. I do not hear any noise when driving regular or when normal breaking. Differential fluid was a tad low. Applied fluid. Still have scrubbing noise. No leaks at hub seal or pinion. Bearings ? Maybe?
View 5 Replies
replacement of a rear tone ring on 06 mercury mountaineer V/6 . I have a tooth knocked off of my left rear . Just wanted to know if there was any special procedure or tricks to it like heating up the old ring or something to remove it or just soak it with P.B Blaster or something similar and tapping it like a bearing race ?
Never did this or have never seen it being done before and rather ask the questions 1st Had the dealer to quote me 500.00 for a new axle and labor said they are impossible to get off or on they most times split ? Old gear head pre-computer car days
View 3 Replies
