Ford F-150 - 1997-2003 :: Misfire Error Codes - CEL On?
Oct 19, 2013
Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors???
I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 14 Replies
Advertisement
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
View 5 Replies
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 6 Replies
I have been having odd problems with my truck for several weeks now and what the problem may be. Occasionally the truck will not start. This happens after it has been run for an errand or to church. The truck turns over but no ignition. Sometimes if I pump the gas pedal very quickly I can get it to start. Other times I have to sit and wait about 5 minutes. I have gotten the following two error codes - P1506=Cylinder Head Temp Sensor and P1299=Idle Air Control Overspeed Error. For two days the "check engine" light was on, but now it has gone out. I have searched for an answer to this problem on these boards and one possibility may be a vacuum leak. Is this the most likely? 1998 Triton 4.6 ....
View 3 Replies
I am having problems with a 2003 Ford F 150 with a 4.2 L V6. The problem is that it is giving me code errors that would indicate bad O2 sensors. I replaced both the upper and lower O2 sensors, and still I get the same codes. I was told by the mechanic with the computer reader that this usually means a bad vacuum seal. He suggested looking for bad hoses, but did not offer much more than that. How to proceed?
View 2 Replies
2001 f 150 5.4 liter with it being code pops up saying cylinder one misfire, I've charge coil and spark plug ran great for awhile now starting to act up again. Got coil check and says still good and look at spark plug and looks still in good shape being just replace two weeks ago. It's running fine but if it sits over night and I get in and start it and begins to shake when I but it in drive and don't even need to move the truck just place it in drive with foot on break. I drive it awhile and it stops and runs fine?
View 9 Replies
Recently bought 98 f150 xlt 3 door 5speed 4x4 4.6l 230k miles for $1k was throwing misfire codes on 1,8,4,3 cylinders. Usually throws two cylinders at a time and never the same cylinders consecutively
Parts replaced:
coils...msd blaster
belden wire
motorcraft plugs...when i did these it ran perfect for a tank of fuel...18mpg no stumble
two cans seafoam through the tank
tank was dropped and drained
fuel filter
one can seafoam intake cleaner
3" exhaust from the Y pipe back
MAF cleaned
Previous owner said to have tested and cleaned injectors but I am not positive it was done... I don't think its mechanical because it wanders through the cylinders and when i changed the plugs it ran spot on. it gets worse the warmer the truck gets also.
injectors?
clogged small cats?
sensor?
View 14 Replies
So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:
P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?
Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.
Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?
View 7 Replies
My 97 F150 4.6 4x4 threw a P0302 and P0401 the other day, I traced the miss fire to a loose injector plug. I reset the codes last weekend, I got in the truck and went to the Dump and to town to pick some stuff up. It threw the EGR code again, so this morning I did a little checking on the EGR I cranked the truck and disconnected the FPR vacuum line and hooked it to the EGR valve and the truck died down but didn't completely die.
Now the green line that went to the EGR valve felt like it had a slight bit of pressure coming from it. Is this normal? I did pull the white feed line from the EGR Regulator and it had good vacuum.
The regulator also makes a humming sound when you cut the truck off. Ill be pulling the alternator this weekend due to it going out last night, while I'm in there if Ive got to pull the throttle body id rather do it while I'm elbow deep in it. So does it sound more like a Clogged Throttle body or a Faulty sensor?
View 4 Replies
Here are the codes I'm getting:
P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean
are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st
View 4 Replies
I have a 1996 Ford E-150 van that has a misfire. The plugs, wires, cap and rotor have been changed and I still have it. The error codes come up as cylinder 3. ( I was getting the same before I replaced everything.) Scanner also says lean on bank 1. It also says that the O2 sensor behind the cat is not doing much.
View 3 Replies
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 Replies
I am getting P0355 error code and potential misfire codes on all cylinders. Engine light and VSC stays on now. Idle is unstable and power is a little jerky at times. I bought a Denso direct ignition coil to replace, however, Cyl 5 looks difficult to access.
View 3 Replies
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
View 13 Replies
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
View 7 Replies
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
View 7 Replies
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
View 3 Replies
Truck wont start idm communication error all the fuses are good and the relay seams good I switched it out with another relay 340,000 miles how do I know if its the IDM r not... I'm sure the idm is not cheap...
View 2 Replies
I have a 03 F150 with a bi-fuel 5.4 engine an it has 195000 miles. I have had trouble for some time now with misfires. I bought the truck in october of 2011 with 125000 miles and replaced all the coils and spark plugs because it was misfiring badly will running on CNG. It was fine on gasoline and never had any codes. After I replaced the plugs and coils it ran fine on CNG and gasoline.
This summer 2013 it began missing badly at highway speeds only when running on CNG. If I accelerated the miss would go away until I was light on the throttle again.I checked the misfire count and found the bad cylinder and replaced a coil. Then a day later same thing on another cylinder. I swapped a coil from another cylinder and problem went away for a day. Eventually I chased the misfire around all the cylinders on the engine until I had ended up either replacing a spark plug or swapping a coil on all the cylinders. And I still had a misfire. It seemed to be worse on days with temperatures above 90 degrees. Eventually I got it to stop misfiring.
So now 5 months later I am back again with a misfire. This time it is misfiring on both gasoline and CNG and under any throttle conditions, except coasting. I have no codes. And the misfire monitor is sending me around the engine again. I have replaced a spark plug in two cylinders and swapped 4 coils.
I'm ready to buy all new coils, but I want to be sure that it is not a waste of money since the old ones only have 70000 miles on them.
Two days ago I had the misfire monitor saying #4 in the evening and the next day without me having done any work on it it was saying #6. Later that same day it said #7 and I still hadn't done anything other than drive the truck.
I checked the connections at the firewall on the drivers side with the three large plugs that are held in with a 10mm bolt, they looked fine, no corrosion or burnt pins. I checked the connection at the ACFM which also looks good. I will check the connection at the PCM in the next day or so.
Some other problems that may be contributing:
1. I occasionally get a U1262 code (scp fault)
2. Sometimes when I check the misfire monitor it only shows 7 cylinders, sometime 9 cylinders. I am using an Innova 3160 scanner.
3. I have either a leaking valve cover gasket or leaking head gasket, because I have oil dripping from the rear bottom corner of the passenger side cylinder head right above the exhaust pipe.
View 5 Replies
Have this code Po155 oxy sensor heated bank 2 sen 1. I have replaced all sensor in the tail pips and check engine light code still comes on.
View 7 Replies
About 3 days ago I noticed my engine RPM was around 250 higher than usual. Usually my truck idles around 550-600 rpm (I know this is low). Anyway, yesterday it threw the P1506 "IAC over Speed Error" Code. It is idling very rough, shifting weird, but does crank up fine.
My truck is now at 93,000 miles and I just cleaned the IAC at 87,000 miles due to the common no start condition. I guess I am going to get a new IAC now since another code came up.
Well, my question is it came up with two other codes also:
P0171 - System too Lean, Bank No. 1
P0174 - System too Lean, Bank No. 2
Do you think the P1506 (IAC Code) made the O2 Sensor codes show up or is it really the O2 Sensors? I just changed my two upstream O2 Sensors around 90,000 miles. Should I get a new IAC or try to clean it again?
View 13 Replies
