Ford F-150 - 1997-2003 :: Intermittent Grinding / Dragging Noise Coming From Pulley
Oct 14, 2016
1997 4.6L.. Have an intermittent grinding / dragging noise coming from the pulley (?timing) area that I'm trying to pin down. Both the alternator and tensioner were replaced prior to the noise starting. The ac compressor and the power steering pump are original. The fan clutch was replaced about 4 years ago and the water pump 8 years ago. Timing chain / guides / tensioner are all original.
I don't notice any of the common ps pump indicators (whine increase when steering) but noticed the fluid level was down slightly and that the pulley seems to have some inward - outward play with the belt off. I also don't have any other engine symptoms like rough idle or any codes being triggered. How to isolate the culprit?
View 2 Replies
Advertisement
I have a very slight grinding noise coming from the PS pulley area. Its possibly bearing noise although its hard to say. Is there a specific torque requirement. Any good parts...
View 1 Replies
I have a 2006 Subaru Forester with 115K miles. It's been well-maintained and well-loved.
For the past few months, the brakes have been inconsistently making a dragging/grinding noise when coming to a stop at low speeds (<5mph). It sounds to be coming from the front half of the car - I can feel it vibrating a little near the driver side. We've taken the car in to be looked at three times - each time, the mechanics think they've heard the noise and report there is absolutely nothing wrong with the brake pads or rotors. Twice they reported a shim was out of alignment. After the last shim adjustment, the noise got a little better - instead of grinding, it's more of a dragging sound now. Because the noise is inconsistent, I haven't been able to crack the formula of the conditions that produce it, other than that it only happens as I'm coming to a stop at very low speeds.
Is there something besides the brakes we should be having inspected? Does this sound safe to drive?
View 10 Replies
I have a 97 250 LD 5.4 that suddenly has a grinding noise coming from the area where the transmission and motor meet. I took the inspection plate off the transmission and can look up inside there and see everything moving. I use a screw driver and if I flex the plate that mounts between the transmission and the motor I am able to get the noise to quiet down until I release the screwdriver and then the plate flexes back and scrapes making the noise again.
I can not see where the plate is grinding when I look up inside there. I can't figure out how to fix this.... Why it would just start doing this on its own as none of the bolts on the housing have been removed except for the two bolts that hold the starter on. (Changed it a couple of weeks ago). Thought about loosening the bolts on the tranny housing but I'm afraid that it would open me up to further problems???
View 4 Replies
I have another issue. I just started having problems when braking. Every time I brake there is thing loud grinding noise that sounds like it coming from the back tires but there isn't a squeaking noise like there is where you need new brakes what else could this be??
View 2 Replies
Over the past few months I'd noticed an intermittent grinding noise coming from my left front wheel at low speeds. I took it in once but it refused to play along so I finally managed to catch it on camera and let the dealership listen to it. They booked me for today, saying it sounded like a wheel bearing (to which I agreed) and I dropped her off around ten, not expecting it to cooperate for the second time.
I got a call from the dealer around 2 PM saying that they were able to duplicate the noise and that when they took the left front wheel off and ran the car on the lift with the rest of the wheels off the ground, the noise went away. Even stranger still, when they put the wheel on the tire balancing machine and spun it, gronch, gronch...gronch, gronch....gronch, gronch. It was coming from inside the wheel! I gave them permission to dismount the tire from the wheel and about ten minutes later I got another call saying they'd found a handful of tiny hard rubber balls inside the mounted wheel/tire assembly that were rolling down the inside of the wheel and causing the grumbling at low speed.
Here's the kicker: they were in all four wheels! The tech even saved them for me so I could take a look and they don't look like anything mass-produced; some are larger than others, some are round and some are oval-shaped but when I dropped one on the glass advisor desk, it made a very clear 'Clink!'.
View 29 Replies
I have an '03 Screw which I've noticed now has an intermittent muted beep coming from somewhere in the interior of the vehicle. I've had the truck for 9 years, and this is the first time I've noticed it. It seems to come randomly but no more frequent than 2-3 minutes apart. As I am typically driving the vehicle, I cannot stop to locate the source. It reminds me of the low battery beep on my Blackberry, but like it's tucked away in the console or glove box (I checked - it's not the BB...).
I have a recurring SES light which is attributed to cylinders 1&4 misfire (discussed at length in a different thread), but I don't know what would cause this beep. I have read about the 5x5 "airbag light" beep, but this doesn't seem consistent with that. It does not seem like a repeating pattern - just a single beep, which sometimes varies slightly in length but is consistent in pitch and volume.
It's another thing in the growing list of gripes that are pushing me toward selling it. Just afraid of something big coming along unexpectedly... trying to manage the little things so they don't turn into that big one.
View 4 Replies
I have a 2005 Highlander that had repeated rear brake noise problem after the dealership serviced the brake in May this year. The sound was like dragging or grinding. After that, I brought my car back but the noise came up every time in 3-7 days. Here is the of the service record from the dealership:
5/31/2011: initial maintenance. Rotor resurfaced, pad replaced
6/17/2011: Adjustment and lubrication.
7/13/2011: Replaced the pad.
8/20/2011: Technician could not hear the noise during drive test. Ticket withdrawn.
8/26/2011: Tighten e-brake, lubrication.
Tech told me the left and right brakes were not balanced. I recorded the noise in the following Youtube video: [URL] .....
Turn volume up and notice the last two stops. What I should say to the dealership service? I plan to take the car back in a few days.
View 1 Replies
I have a 1999 ford f150 with 4.2 and 156,000 miles, about a month ago I drove from my house to a friends house a few hrs away. On my way home I started smelling a burning smell and stopped and my brakes were smoking. So I replaced brake calipers and still they drug then I changed brake lines and I can still only drive a few miles with out them getting really hot and dragging....
View 9 Replies
My husband bought a 1997 Ford F150 and the seller said he changed the brake lines, but the back brakes have dragged on takeoff since he bought it. Just put new shoes on it and it's still doing the same thing, but now the drums are getting hot. Is it possible that the seller got the brake line backwards and that might make the back brakes drag?
View 2 Replies
I have a 2003 Ford F150 with a 5.4V8 Triton 4X4. The truck is about to roll over 200K here soon. I am feeling/hearing a vibration/grinding sound coming from the truck when I am moving slowly and making turns, either left or right turns. Seems to happen more so on left hand turns. I have changed all power train fluids and filter, and still does it. I do not feel or notice the vibration/grinding when I am going straight or at highway speeds. It is only when I am moving from a stop and making turns. How to diagnose, find out, repair, fix this issue?
View 4 Replies
Over the last few days my f150 has developed a really annoying squeal that's intermittent. I can never really predict when Ill hear it. Usually I first hear it when I am accelerating to a speed greater than 30 or 40 mph. And it will continue if i keep my foot on the gas or if i slowly hit the brakes. Usually the only way it will stop is if I slow down to under roughly 30 or if i hit the brakes. pretty hard.
But sometimes Ill hear it at various speeds just for a second or two, usually when I am turning or when I am decelerating by taking my foot off the gas and not braking. again its hard to predict. It sounds really similar to a car with squeaky brakes. and just like squeaky brakes, you can hear the noise slow down as the f150 slows down. but again it doesnt only happen when i hit the brakes. I dont know what it is.
View 10 Replies
I have a 99 f150 4x4 that has done this twice, once last year and once this year during hot (90+) weather. I'll notice the vehicle seems like it doesn't want to go. Park overnight and it will work ok. Last time it happened the other day I stopped at wally world and both front wheels were real hot and I could smell the brakes. Came out hour later and when I pushed the brake pedal to put it in gear the pedal went to the floor.
Pumped up pedal and drove off but truck would barely move, drove 10 mph to a buddy of mines shop and it sat overnight and worked perfect the next day. He inspected everything and seems to think it might be the abs control unit. He noticed a small amount of fluid had come out of the unit and dripped on the ground. Also no abs light or brake light has ever come on
View 9 Replies
I'm trying to find out why my truck has a grinding noise on the passenger side when my truck first starts driving for the first 1/4 mile. It stops after that or when I apply the brakes. Do I have a brake sticking or something more serious?
View 1 Replies
My 2001 5.4 makes a grinding noise when starting. Not all the time but some of the time. it will always start but it is annoying. Need to know if this would be starter or solenoid?
View 4 Replies
Bought a high mileage 99 f150 4x4 yesterday. In the process of cleaning her up, the water hose hit the disc brakes on the drivers side and it was hotter than a BBQ grill! Ok, immediately I thought this isn't good. Jacked her up and pulled the caliper. Pads were almost gone so replaced them with a new set, went for a drive. Now the damn things were smoking so bad I thought they were gonna catch fire! Sticky caliper , right? Stopped and got one then realized that the passenger side started doing it too.
Another trip for the other caliper and new pads because these were toast. I mean just burnt to hell. Before I started working on the truck again, I checked on here and I'll be darned if I didn't find out that the old brake hoses might be acting like a check valve because of rust and deterioration. Got a set of brakes hoses too. Put everything on this morning and works like a charm.
1999 4.6 XL
Passenger side done
View 1 Replies
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission. I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced. I have also just had a new hydraulic clutch kit installed.......
View 1 Replies
I have a 2002 f150 5.4 with 3.55 limited slip... For months now every time I hit a bump with the front right side there is a loud bang (sounds like a wore out bushing), and if I am driving slow at an idle you can here a thump every time the wheel goes around. And when I turn all the way it sounds more like a grinding sound.... The noise is getting very bad, what it is. I am very mechanically inclined but cannot figure it out.
Everything in the front end seem tight. When I lay under it if I get someone to spin te wheel the thump sound sounds like its in the front dif, kinda echoes through the front drive shaft but u joints seem good. I really think it's in the dif, and I'm hoping the banging noise I hear when I hit bumps is the same problem as the noise when the wheels go around....
View 3 Replies
I recently sold me 91 F-250 and got into a 98 F-150. It's a SuperCab 6.5' bed, 4x4 off-road, 3.55 gears, 5.4 v8 auto. I love the truck, but I am having an issue with a noise at startup.
Every time I start the truck it fires right up but it makes a grinding noise AFTER it starts for about 3-5 seconds. I thought the starter wasn't disengaging in time so I replaced it. The starter I took off was fairly new. It's teeth had just a little wear and the flywheel had no visible wear. I put in the new starter and there was no change at all.
I also changed the oil and filter using Motorcraft 5w-30 oil and a Motorcraft filter. I also started it without the serpentine belt to rule out a pulley bearing. What the noise could be? The truck runs absolutely excellent, by the way.
View 5 Replies
I have a '97 Ford Escort. I drive over an enormous pothole. Immediately, I heard a dragging noise on the left side of my car. The noise only occurred if I went over terrain that caused the car to somewhat bounce up and down. I got out of the car. I discovered a metal bar hanging down near the left wheel. I then noticed another one hanging down near the right. The bars appear to be either ends of a long rod. These bars curve down away from that rod. One has a hole through the end. One has something like a nut or bolt on the end.
View 7 Replies
An idler pulley on my 2002 F-150 seized and snapped the serpentine belt. The pulley is below and to the left of the belt tensioner. The pulley doesn't have a bolt but a hole that looks like an allen wrench would fit it. I couldn't find an allen wrench to fit it. Called AutoZone and they have a pulley removal tool in three sizes. What size wrench would fit the idler pulley? I want to make sure I get the correct size tool so as not to screw up the pulley when I start pulling on it.
View 2 Replies
