Ford F-150 - 1997-2003 :: Grinding Then Thumping Going Into 4wd - Vacuum Solenoid?


Jun 15, 2008

I have 97 4x4 f-150 V6 4.2 litre that in 2wd tries to go into 4wd causing a grinding then a thump. When I put the truck into 4wd there is no grinding or thumping.

I believe one of the vacuum solenoids could be bad. Just was wondering which one would cause it to want to go into 4wd while in 2wd. The left most solenoid looking under the hood is the 4wd and the other with the pink vacuum is the 2wd.

I have no vacuum from the solenoids but from the lines going into them.

View 14 Replies

Advertisement

Ford F-150 - 1997-2003 :: 4WD Not Working / No Click On Vacuum Solenoid

1997 f150 electronic 4wd not working, lights on dash not working(they light up on start up) replaced transfer case motor still not working, checked all fuses, Do not feel or hear clicks on vacuum solenoid, Top vacuum lines on both have vacuum. Where do I go from here? What do I check next....

View 9 Replies

Ford F-150 - 1997-2003 :: 4wd Not Engaging / 2wd Solenoid Always Activated

Found out the hard way that the 4wd does not work on this new stupid truck. I've been troubleshooting the solenoids and confirmed that the 2wd solenoid gets grounded and will read ~12V when switched to 4wd; however, the 2wd solenoid always remains grounded and will always read 12V across the plug no matter if it's in 2wd,4hi,4lo. What would cause this? It seems that I would have vacuum going to the front differential from both the 2wd and 4wd solenoids at the same time, thus not allowing it to go into 4wd. BTW, this is on a '98, 4.6, turn dial 4wd

View 14 Replies

Ford F-150 (2004-2008) :: No Vacuum Coming From Engine To IWE Solenoid?

I have no vacuum coming from the engine to the IWE solenoid. This is making my hubs stay locked all the time. where this line from comes from and how to fix this. Which line is the line from the engine, the one with the T in it or the other one?

5.4L V8 2004 New Style

View 5 Replies

Ford F-150 - 1997-2003 :: 2000 - Bad Starter Solenoid Relay?

My truck has started fine every time I've turned the key except for last night after work. I got in had all the lights on the dash and dome lights. I turned the key and nothing. Not even a click. Hooked it up to a company truck and it fired right up and ran fine. Drove home shut off and then started it a little later and it started fine. Then this morning it wouldn't start. I hooked up the jump pack and still nothing. I drove my fusion to work and when I got home I went out and it fired right up like nothing happened. Does the work sometimes not work other times sound like the solenoid on the firewall? 2000 4x4 4.6 auto 253k miles

View 4 Replies

Ford F-150 - 1997-2003 :: 4R70W Code P7081 - Shift Solenoid?

Code P7081

Do I have to drop the valve body to get to the shift solenoid? Is there only one solenoid? Anything special or tricky I should know about?

View 14 Replies

Ford F-150 - 1997-2003 :: No Crank / Starts Only When Solenoid Is Jumped - Slow Starter

I am having some weird issues with my 2000 F150. When I turn the key all the dash lights go out and no start. Ran 2 wires from the solenoid to a switch and it will eventually start. The starter will start real slow almost like the battery is almost dead and then speeds up more and more till it eventually starts. After it starts the theft light stays on the whole time. At this point I have no clue what is going on.

View 1 Replies

Ford F-150 - 1997-2003 :: Low Presser AC Switch Died / Start Solenoid Just Clicks Sometimes

On my 97, just had a new engine installed. Suddenly the Lo presser AC switch died. Now the Start Solenoid (I think) just clicks sometimes. Is this Solenoid on the Firewall the Start Solenoid?

View 6 Replies

Ford F-150 - 1997-2003 :: Brake Pedal Switch Or Shift Interlock Solenoid?

I have a 99 f150 and it won't shift out of park. The taillights work and I tried to turn the key forward and move shifter to neutral but it didn't work. Is it the switch on the brake pedal or the interlock solenoid by the shifter?

View 12 Replies

Ford Super Duty (1999-2016) :: 2010 F250 - Vacuum Solenoid Not Getting Electricity?

I have a 2010 f 250 super-duty and i cannot get vacuum past the solenoid mounted on top of the radiator. Ford has given me nothing but bad advice. I know i have a vacuum leak after the solenoid and need to replace the lines going to the two hubs but when i switch on the 4wd and hook up a vacuum gauge the vacuum is good up to the solenoid about 12 inches. i constantly have 12 volts going to the center lead but nothing else in the other two leads either in 4 high, 4 low, or 2wd. Am I missing something here? shouldn't there be a voltage change when i turn the switch to 4wd to actuate the vacuum solenoid to let the vacuum pass thru the solenoid? I have tried replacing the solenoid but that did not work. Also use rubber vacuum line and make at down to the hubs?

View 4 Replies

Ford F-150 - 1997-2003 :: 2001 - Won't Start / Only Get Solenoid On The Firewall Click Each Time Turn The Key

Ok so I was looking at my blend door actuator motor to see if it was working. Just took off the bottom vent cover, turned key on and moved the air mixture to see if the motor worked. (it didn't) Then I went to start the truck and all I get is the solenoid on the firewall click each time I turn the key. I put a meter on the opposite side of solenoid and I see 12v across the solenoid. I can't image i did anything while playing around by the blend door actuator motor. I guess I'm looking for confirmation that the next logical step is starter and starter solenoid. Is there anything else I could be missing? is there anything else in that circuit between the solenoid on the firewall and the starter? I also cleaned the battery terminals and the terminals down on the starter solenoid. I also tapped the starter a bunch and put a charger on battery and tried jumping the truck too. Everything else works.

View 10 Replies

Ford 6.7L Power Stroke Diesel :: 2013 - Four Wheel Drive Vacuum Pump And Solenoid Location

I have a 2013 6.7 and i cant seem to get my 4wd to work in auto position on hubs i think i have it narrowed down to the solonoid for it but cant seem to find location on it.

View 3 Replies

Ford F-150 - 1997-2003 :: Water In 4WD Vacuum Actuator

I have a 2003 F150 supercrew 4x4 and I'm on my 3rd - 4wd vacuum actuator this winter so far. Somehow water is getting into the actuator itself mounted on the axle and then when it gets cold enough it freezes up and won't work until the heat from the engine thaws it out and then the 4x4 will engage.

Every time I've changed it I have found the part to have about a quarter cup of water in it. and can't figure out where the water may be entering these things. There also was no moisture in the vacuum lines when I blew them out.

I've been using the Dorman brand replacements from O'Reilly, they have a lifetime quarantee but I'm sick of swapping them out every month...

View 3 Replies

Ford F-150 - 1997-2003 :: Vacuum Controlled 4x4 Not Working

I'm working on a 03 Lariat F150 with vac. controlled 4x4 (I'm new to this one). Transfer case works, ft drive shaft turns, but the front axle wont engage. The servo works, and the linkage is tight on the shaft, and the shaft turns back and forth, and the ft axle can be engage manually by working the small lever back and forth with the servo disconnected, but when zip-tied in place it doesn't stay in 4x4, so something is broken, worn out, or disconnected inside the housing.

Also I repositioned the servo back a bit with a spacer to make sure it wasn't a length of travel issue, and is not - the problem is definitely inside - the linkage feels sloppy when manipulated with the servo off.

Since Ive never had one of these apart I thought Id ask first (also a new thing for me), so I'd know what parts to get (I don't live "in town"), and I figger this isn't the first one of these to break. So I am sitting down - what am I in for??? It looks pretty straight forward, but somehow I doubt it is...

View 14 Replies

Ford F-150 - 1997-2003 :: P0401 Code - Vacuum Lines?

So here's the background. I recently bought this truck. It's a 97 Ford f150 4x4 4.6l 99w vin code. Anyway Driving it home got a p0401. No problem. I Applied vacuum from other vacuum source to EGR engine stalls. So to me passages are clean in the throttle body. I checked to verify and indeed passages are clean. No while doing so I noticed no vacuum was making its way to the dose valve thing. Strange.... So took the line that runs to the passenger fender to dose off and it was impossible to blow air through.

So I cut out the clogged section found solder in the line. I filled the gap I now created using some 5/32 vacuum line reconnected to test and to my anvil still not vacuum. So I disconnected it again. Went directly to where the yellow/orange dose vacuum line connects to at the passenger fender and to my surprise no vacuum there either. No my question is. Am i suppose to have constant vacuum to the dpse or I'm I just being an idiot. And two if I am suppose to when the vacuum line runs into the passange fender where does it go from there and could I have a major issue in my hands?

View 1 Replies

Ford F-150 - 1997-2003 :: Vacuum Diagrams For 4 Wheel Drive?

Looking for the vacuum diagrams for the four wheel drive, where I can find them?

View 10 Replies

Ford F-150 - 1997-2003 :: Vacuum Leak When Engine Is Under Load

It has been since the 80's that I have attempted to do any work on a vehicle. How do I find a vacuum leak and where is my vacuum canister. I am assuming that it is a vacuum leak for anytime my engine has a load on it the air stops coming out of the dash vents and goes to the defrost vents. I have an 2000 F150 with the large engine with about 112,000 miles.

View 11 Replies

Ford F-150 - 1997-2003 :: 1998 - Air From Defrost Only - Vacuum Leak?

This has been on going for the past year. The blend works fine. Fan speed works correctly. The selection for ac, max ac, etc., will only allow air through defrost vents. Vacuum leak?

1998 4.6 auto super cab

View 4 Replies

Ford F-150 - 1997-2003 :: Using Propane To Find Vacuum Leaks?

Question. I have never used propane to find vacuum leaks. I always use starter fluid. I understand propane is better but how nuch do you use? Low volume, or a lot of propane. I just don't want to kill myself.

View 14 Replies

Ford F-150 - 1997-2003 :: P0401 OBD2 Code / Vacuum Leaks

I've had a 0401 code on my truck for the last two years. I've replaced the EGR valve and the dpfe sensor a couple of times, with fomoco parts. Ive also cleaned out the egr tube that comes off the exhaust manifold. In this time I also discovered a couple of vacuum leaks and replaced those. I changed the pcv valve, tried running 93 octane gas, and had a mechanic friend run a special smoke through the vacuum lines to find more leaks. Also put a brand new gas cap. I have an obd computer and cleared the code repeatedly but the light always returns.

View 14 Replies

Ford F-150 - 1997-2003 :: Code P0171 And P0174 - Vacuum Leak

I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.

2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.

I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.

View 2 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved