So Iv a couple weeks ago I bought a 1998 f150 and today I was gonna do the fuel filter and saw the line goin to the engine was broken and they put a rubber hose in line. The hose is only about 6inchs and I work at ford so I got the price on the whole fuel line running up to the engine. I was just wondering if any repairs that work for metal fuel lines.
View 4 RepliesIt appears the Engine By fuel line connectors are broken. I searched for DIY'ers on how to fix, but so far I only see those related to fixing other sections on the fuel line, not this upper section. It's on the passenger side. How to fix it?
View 3 RepliesI have a 1990 Ranger with a 4.0L that I just changer the intake gasket on. I broke the fuel line at the Fuel Pressure Regulator. Cant seem to find one anywhere. It is a nylon inside/rubber outside with a cloth mesh and quick connect fitting line. Where to get one? Can I hose clamp it the FPR by cutting off the connector that broke?
View 1 Replies1998 Explorer. The fuel pump went out so today I dropped the tank to replace it. I got the 2 fuel lines off and the 2 electrical connections off with no problems but when I went to try and take the vapor line off, the tabs on the connector were brittle and broke. Now I am stuck not being able to put everything back together since that line wont lock on. I was wondering if anything I can do.
I have tried looking online to no avail except for one site selling ford part that has this line for almost 300 dollars. It is just a plastic line that leads to a metal line. Even the Ford Parts site doesn't carry it! That's insane! I was thinking of cutting the plastic line off where it meets the metal line and using rubber fuel line with hose clamps on the line and the plastic fitting on the tank. I just dont know if this will be good enough.
I am a proud owner of '97 Grand Prix GTP, it has always been a great car with really low maintenance for me. A few days ago I noticed a mild fuel smell and I checked the gas cap, the external fuel filter, etc... Then I lifted the hood and I saw that one of the two fuel lines that run between the firewall and the brake fluid reservoir had a seepage leak in front of the factory loom that secures both lines before going over the supercharger and on to the fuel rail. A fuel leak needs to be repaired immediately, so this is where I am so far.
I noticed that the leaking fuel line is actual a rubber/plastic fuel hose that is covered by a plastic heat proof cover that protects the hose. It runs from the firewall to the fuel rail along side another fuel line of the same size (a supply & return line I believe). Just before going over the supercharger they both have quick connect metal ends that meet two metal fuel lines that end up at the fuel rail. My current issue is that this plastic/rubber hose section of fuel line is discontinued and no longer available to order according to my local GM parts dealer. The way I see it, hunting down this part can be Plan A and Plan B can be duplicating this hose by making it with high pressure fuel injection hoses and the appropriate quick connect fittings.
I have a 97 f150 4.6 4x4 i cant get my engine to line back up with the motor mounts. Is there a trick to doing this? I've tried to lift the motor several different ways, but still nothing. Its like the motor isn't going back far enough. But it cannot go back any more without hitting the trans?
View 8 RepliesRecently I have been having a strong gas smell coming from my 1997 F150 Supercab 4.6L 2wd. It is not happening all of the time. I have also been hearing what sounds like a vacuum line leak. A loud shrill which varies with the engine rpm. This also does not happen all of the time.
View 1 RepliesDad's 97 dodge neon still showing a CEL and a code for a misfire but according to code reader it has something with the fuel line that is causing not enough fuel to get to engine. Car has a new fuel pump (about 6 months old) and it runs fine for a while then will sputter then will run fine for a while and back and forth. What it might be?
View 3 RepliesHaving trouble figuring out how to remove the rear fuel line from the fuel pump. Doesn't seem to be the type that uses the quick disconnect tool like the front line does.
View 5 RepliesWell the time has come where I don't like the way my brake lines look running to the back of the truck. Question is, What size are the fittings on the ends of the lines? I know I will have to special order the line that goes from the frame rail down to the rear axle tube, but is the line that goes from there to mid way frame rail a standard size? I don't want to have to order that if I don't have too.
View 1 RepliesHad a little fender bender. Right after that i noticed the battery red light was on. When I got it home I took the solenoid off the firewall (all the battery wires meet here). When you put 12 volts to the small terminal, the solenoid pulls in and the two big terminals are connected together. That works. When installed on the truck and startup, I have no 12v voltage at the small terminal. Don't have a diagram, but service manual says something about fuse #14 under the dash feeding the "battery cutout".. Checked that fuse and its o.k. .... where does the 12 v signal to the solenoid come from ? I assume somehow it triggers after the alternator starts charging ?
View 12 RepliesI tried searching, but couldn't find anything. I have a '97 F-150 with the 5.4L and I have a plastic line coming off of my intake that I don't know where it is supposed to go. I don't know how or when it got disconnected, but I can't seem to find anything within reach of it that it can connect to.
View 4 Repliest's a '00 extended cab swb 4.6L with 4r70w trans. I have a Hotchkis TVS 2/4 kit on it. It's been lowered 3 years now and I've never had any real issue. But I started noticing a small vibration through the floor so I took my driveshaft out to be balanced and new U joints installed. Ever since then I've had an audible "hum" from the rear whenever I go over 75mph. It only does this under load (hill, etc) and I don't hear anything until then. The driveline shop told me it was my pinion angle and I've tried shims with only slight improvement. I'll replace the driveshaft after I do a motor and trans swap down the line, but it's out of the budget for now.
View 2 RepliesNew to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
I got a new to me 1998 F150 a week or so ago but it got parked quickly when I realize the gas tank strap was broken. I took it to a dealer today and they replaced the strap.
View 3 RepliesTransmission oil cooler line, lower one, is leaking. I think to use pvf, black ones, brake line instead of new transmission oil cooler line. I did replaced upper one with new transmission oil cooler line before a few years and it is rusty already as those line are only zinc plated as opposed to plastified brake lines.
View 12 RepliesWhen I lost the rear brakes due to a rusted line, naturally the ABS light came on. Will it automatically reset when everything is repaired and working or is there something else that needs to be done?
View 2 RepliesI am replacing the high pressure power steering line on my 2000 Lightning and have a question about the fitting that goes into the steering gear. The new hose came with a black rubber o-ring that the instructions seem to indicate goes on the end of the steering gear fitting. The problem is that I did not see any o-ring on the original hose end or in the steering gear itself and the hose did not leak there (it was leaking on the pump fitting). Should there be an o-ring at the end of the fitting or does the fitting go on without it and uses a metal to metal seal? If replace this hose, did you use the o-ring or leave it out? Does it go on like this? Or like this?
View 4 RepliesGot F-150 4.6 cooling system leak on the heater line (farthest back line) coming out of the block. Fitting looks to be steel. How does it attach/ do I need to remove the Intake to replace?
View 5 RepliesHow does it come off. I wasn't able to turn the axle vent without turning the block on axle for the brake lines.
I would like to remove the brake system from my current axle without breaking any lines open, then putting a new axle in and put the brake system on the truck to the new rear axle.
I noticed a vacuum line hanging under my 98 F 150 4x4 I traced it out to my front axle question is where does the other end go I have looked but no luck to where it goes.
View 5 Replies