Ford F-150 - 1997-2003 :: Fuel Gauge Malfunction - Jump Up All The Way To Full When Started
Jul 20, 2013
I have a 97' F-150 4.6 L and I've been having some fuel gauge issues.... I filled up my tank up and I drove it 130 miles and it still said full tank... even when I had 1/2 I would start it and every time I started it it would jump up all the way to full and slowly drop down. Then randomly last night it started working... I noticed as I hit rough patches in the road and bumps it would usually fluctuate, but it would also fluctuate up... It read I have 3/4 tank last night and I go to start it today and its back up to full! I don't understand... Wouldn't a bad sending unit just stop all together?
View 1 Replies
Advertisement
I have a 2001 F150 Supercrew (5.4 V8, 2WD,Auto trans) and recently when we fill the gas tank, the fuel tank doesn't go all the way up to the "full" line. Don't know if this matters but: about a year 1/2 ago in a little town (while on vacation), we broke down and the trouble was the fuel pump. The little town did have a small auto-parts store, and luckily had the fuel pump we needed. Unfortunately we didn't have much as far as tools and we wound up tearing/cutting the filler hose and the vent line.
The little auto store did not have the correct rubber filler & vent hoses for my truck and would take a few days get in stock. We changed out the entire fuel pump and sender unit, and were able to modify some rubber hoses for a new filler & vent line hose. Everything worked great for a year 1/2 but in the last few weeks we have noticed that when we fill the tank, the gas gauge does not go all the way up to the "F" line to show full. With the price of gas, it is important to know exactly how much is really in the tank. Also, is there a battery in the ceiling console for the temperature and compass? Ours just stopped working yesterday.
View 13 Replies
2008 hyundai santa fe. 106,000
Bought the car six months ago.Found out 2 weeks later we couldn't put gas in it. Dealership refused to fix it because we bought as is. So we managed to find one gas station in a 20 Mile radius that we could put gas in it.It takes around 10 minutes to put half a tank in. Shortly after that the gas gauge started to fluctuate from full to empty. And the check engine finally came on. Had the the check engine light checked.Fuel level sensor A was faulty. Took it to a local Goodyear in stead of the dealer ship. The sensors were 119.00 a piece and the labor was 145.00 to replace both. Had both replaced .Fuel gauge is working correctly now. But still having issue putting gas in car.
View 1 Replies
Two years ago I acquired a very very nice 2001 F350 DRW crew cab. The person I purchased it from put a Remanufactured 7.3 in it and set the truck up to pull wedge trailers. He put 25K miles on it and put it on Craig's list where I found it. It just turned over 300,000 miles.
One of the changes he made was to install a 70 gallon fuel tank in the frame rails below the bed. He told me that when the gauge reads EMPTY there is still 20 gallons in the tank. I remember him telling me that this anomaly is due to using the stock Ford pickup in the larger tank.
I have never filled the tank because so far the truck is used locally. I usually put 10 to 20 gallons in and when it gets to E I do the same fueling.
Then one day I turned the key on and the needle went up and beyond the full indication.
I can get under it and maybe the tank has some name or model number on it.
The truck runs fine, but the gauge concerns me. Eventually the truck will be making round trips from Chicago to our retirement home in Santa Fe, NM. It would be nice to have a working fuel gauge!
I have spoken to the person I purchased the truck from. He installed the tank as part of a complete upgrade that included a re-manufactured 7.3. The fuel tank is a 67 gallon Titan mounted between the frame rails. He believes that the original Ford sending unit was installed. That means it has 300,000 miles on it. I had the truck on a lift yesterday and it is a very tight fit. The garage said the best way to do the repair is to remove the bed. Six bolts, disconnect the tail lights and the 7 pin trailer connector and it is off.
So, my questions now are... Should I stay with a new Ford sending unit or are there better ones to install? Are there any other updates to the fuel delivery system that should or could be done at the time?
View 8 Replies
Well besides the pyro breaking friday BEFORE live tuning,and the exhaust leak I gained on the way to Texas(not inpart of the pyro not working). Now the fuel gauge is stuck on full. It looks good,200+ miles and still on full. Could it be the gauge,or possibly just the sending unit? Maybe a fuse?
View 14 Replies
I have a 2002 supercrew 5.4 triton. My coolant temp gauge is acting up. When it starts up its obviously in the cold range but when the truck begins to get up to temp, the gauge only goes up 1/4 full. What it can be?
View 4 Replies
As title really, it's a 1997 K2500 Suburban 4x4 auto 454. I haven't used the sub for a while but got in it the other day and it fired up all fine and I then looked to see what fuel I had left only to see the needle right over to full. Well I know it is nearly empty and I've never had the guts to fill the thing or should that be had the funds to fill it to the top, so know it is wrong. I got under the truck and unclipped the rear most wiring connector just infront of the fuel tank but the gauge still reads full. I suspect either the gauge is faulty (so is there anyway of checking) or the sender in the tank or wires in the tank have shorted (again anyway of testing without removing the tank).
View 3 Replies
2003 Ford Explorer fuel gauge does not show full after fill up. The Ford service stated that it can take up to 17 minutes (of running time) for the fuel gauge to show full after fill up.
View 7 Replies
I've been having a very erratic fuel gauge issue as of about 2 months ago. My fuel level would register full, when in fact I knew it only had 1/2 a tank or so. Then 5 minutes later it would be pegged on full. Under a 1/2 tank the gauge would read any where from 1/2 to empty from 1 minute to the next. So last week I decided to drop my tank and take a look. I was thinking maybe my fuel sender was broken, maybe a loose wire in the tank, or even that my float had dropped off in to the tank.
After dropping the tank, I removed the PK-Up and sending unit and everything was intact. I placed my ohm meter on the sending unit and it checked out fine. So I took the Pk-up and rolled back up underneath the truck and plugged it back in. I had my son turn the key on and off while I moved the float to different levels in order that it would register. It registered empty, 1/4/, 1/2, 3/4 and full just fine as I moved the float to those levels. If you leave the key in the run position and move the float, it won't register or better said, the in cab gauge will not adjust with the movement.
You have to turn the key off move the float and hold it there, then have your assistant turn the key on and the gauge will show the position that you've moved and held it at. I simply removed the plastic cover from the sending unit, and sprayed it down real good with electrical contact cleaner. I didn't scrub the copper contact area at all.
I was concerned that scrubbing might remove more than I wanted to, and really mess things up. I attached an Ohm meter and checked resistance thru out the float travel. All checked out good and I reinstalled it. So now my fuel gauge is working as it should be. I did make a video while I ohmed the Sender Unit thru it's travel, but for some reason it won't load.
[URL] ....
View 5 Replies
I own a 1997 ford f150 V6 engine and I have problems with the electrics. I turn the key on and the engine starts up runs great but I then look at the gauges and not one moves at all the. No fuel when i have just filled up,no tep,no oil,no battery all read nil. I went a drive and the speedo reads 0 it does not move but the truck drives great. Could it be a fuse, does a fuse control the gauges, which one it could be. I have lifted the hood and under the hood on the drivers side there is a box with small and larger fuses.There is one that is very small and the colour is white that's blown. Would you no what that fuse is for.
View 1 Replies
I have a 2003 Buick LeSabre Limited, and everything was going fine with it till recently. The Fuel gauge started to go haywire as in the needle would go to full, then go back down to a Quarter, then back to 3/4, then drop all the way down to Empty, this is still occurring. At first I believed it to be the fuel level sensor, but then I started to notice something else.
A warning message came on stating that the oil level was too low, but when I checked the oil level it was fine, and last night when I was driving with the air conditioner on, I hit a bump and the air conditioner stopped working. I pushed the off button, and was successfully able to make the air conditioner to come back on with out having to restart the car.
The horn has also started to go in and out, and I do not know if they are all linked together by a type of computer or if they are separate.
View 8 Replies
I drive a 2001 Ford F150 4.6L , Miles at 175,000+ (a little more but no more than 176k)
Situation as it happened : Driving home from work for lunch, about halfway home I notice that my Oil Light is on and the Gauge has dropped to below the "L." Engine started making noise, best I can compare it to is to the sound of a diesel engine when it's idle. Immediately pull over after noticing this, shut off engine for about 5 mins, check oil, oil is fine. Turn truck back on, light is off, gauge is normal, and noise isn't as loud as it was before. Drive rest of the way home no problem. After deciding on driving the truck back to work (I know i shouldn't have but I have no other means of transportation, and I work at Autozone so I wanted one of my managers there to check it out) I turn on engine, everything is fine, no oil light, gauge is in the middle of the "H" and "L", only thing wrong was the engine noise, except like earlier it wasn't too loud or shaking the truck. About halfway to work, I come to a stop sign, Oil gauge shoots down below the "L" and the oil light come on.
As soon as that happens engine starts making same loud noise as before (diesel truck idling.) I push the gas to get past the stop sign, and instantly truck loses power in pedal and just shuts off. Make it to side of road, hasn't turned on since. Never had any problems with the truck since I bought it 5 months ago, changed the oil 1 time about 2 months after I bought it. I'm just hoping my engine hasn't seized up on me.
Not sure if this matters, but about 4 days prior to this, truck was making a rattling noise, almost like shaking a can of paint , under the front drivers side, in the suspension. Was told those were probably due to my sway bar link bushings being busted.
After some research on here and other websites as well, I have come to find out that this is pretty common in most Fords? Most people recommend changing the oil pressure switch, and others say it could be the oil pump? Was planning on changing out Oil Pressure Switch, and changing the oil filter/oil , and fuel filter as well. Not sure what else I could do?
View 6 Replies
Fuel gauge reads full all the time except when the key is off. Also the temp gauge reads low. Just barely on the mark for normal.
View 9 Replies
Was driving my truck I have a 97 f150 4x4 4.6L, btw. The heater started blowing cold air and I looked at the temp gauge but it was showing lower than it normally does and then, after a couple of miles or so I looked at the temp gauge again. By this time I was in my driveway. And it was overheating it might have been that way before I looked at the temp gauge again. But any way I opened the hood didn't see any leaks, all my hoses were hot except the top heater hose. Also checked the oil it was full and coolant was too, what this could be? Sounds like a t-stat to me? But could be worse. Also forgot to mention that the oil had no signs of water in there nor the expansion tank cap !
View 3 Replies
I have noticed when I turn the key on the needle moves down just a touch but goes back to full. I have disconnected the wiring harness for the fuel tank and reconnected it. I have tried tracing the harness back towards the front but no luck yet. I'm guessing it's a bad ground or something. And if so what was the solution.
View 5 Replies
So I had the brakes services yesterday at a new shop in town. Normally I wouldn't do this, I like to do it myself. After I dropped the truck off I get a call a while later and the service tech tells me that the passenger front caliper is the wrong one. He says it's actually for the drivers side, but who ever did the brakes last just flipped it upside down and put it on the passenger side. So in essence, I have two drivers side calipers on the front of my truck.
I got under ther and looked and the bleeder screw is on the bottom on the passenger side. I would assume it's supposed to be on the top like the others?
So here's my questions......
1. Is it even possible to put the drivers side on the passenger side (upside down?)
2. Is it really the wrong caliper? It has been working for over two years like this with no ill effects.
3. Should I worry about it if in fact it is the wrong caliper?
I've never done the brakes on this truck actual truck myself. I really hate taking things to the shop because you never know if they are trying to scam you, which I'm pretty sure they were. I left there with only new pads...
View 2 Replies
So my truck felt gutless somtimes, wouldn't start Every couple days , and Fuel gauge stops at half tank won't show full, so I went n bought a new fuel pump..... Well shoot nothing changed . I guess my next move is pull the dash off n fix gauge? It used to be a reliable truck . Now Im not comfortable to let wife drive it . I also pulled the chip to see if that had to do with not starting, also theft light blinks normal. I'm going to get some connector grease n redo all of my wires to c if there's just connection issues.
View 6 Replies
2000 v10 f350 single tank...fuel gauge is stuck on full. I'm on the road so I don't have my drawings so I tried some quick troubleshooting. If I remember right 160k or so is full and 20k ohms is empty...so I unplugged the sender from the harness which should be open and the gauge should read empty. With key on its reading full. I then followed the harness and unplugged it near the brake booster...key on it reads full. Just wanted to make sure I'm not doing anything wrong before I rip the dash apart.
View 6 Replies
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 Replies
I have a 2000 ford F 250 with V-10 engine with fuel gauge stuck. The problem started in the winter a couple years back on a cold night when I fueled the truck with it running. The fuel gauge never went down. I assume this would indicate a stuck float? I dropped the tank and noticed a loose yellow wire. I can't see that the wire was attached anywhere though? A V-10 is not the engine to be guessing with on fuel...
View 1 Replies
fuel gauge does what it wants? It goes down to half way then goes back to full or sometimes even empty. Not a big deal for me because I have gotten used to it. But I would hate to have my wife in here and she thinks it's good and run out.
View 14 Replies
