Ford F-150 - 1997-2003 :: Front Right Wheel Locked Up When Lightly Applied Brakes
Aug 28, 2014
Going down a steep loose gravel drive way, going maybe 5 miles per hour. About 50 feet before the stop sign we lightly applied the brakes and the front right wheel completely locked up. If we didn't turn into the grass we would of stopped in the middle of the busy street. We picked up speed when we applied the brakes, like we were on ice. When I got out, I could see the one long brake mark in the driveway. This happened on a paved road about 6 months ago, it had some loose gravel at the stop sign. I couldn't tell which wheel locked up at the time. This happened on snow in December to, twice. Since the ABS light never came on. Brake pads and rotors needed replacing about 9 months ago. Tires have been rotated, no change. Not sure what it could be. I disconnected the Abs fuse for now.
View 5 Replies
Advertisement
I have a 2001 f150 4x4 5.4 Liter 72000 miles. There is a rubbing sound that is only audible when the brakes are applied. And only when applied with light pressure. The noise will continue intermittently until you come to a complete stop. If the brake is applied aggressively there is no sound at all. I am not sure if it is a brake issue or some thing in the front end that is flexing when slowing down.
View 3 Replies
my 99 s/w 2 started making a squeaking sound coming from the front right wheel area it goes away when I apply the brakes? is that one of those built in warning features to let you know the brake pads are getting low? the brakes have 86,000 miles on them.
View 2 Replies
I have started hearing a noise with my brakes. First thing in the morning when I back up and apply the brakes, I get a clunk or pop noise from the left front wheel. It will pop again once I move forward and hit the brakes. It only does the noise one time when I first apply the brakes in either direction. Once the brakes have been used out on the road and are warm, there is no noise when changing directions. I've had this noise in another car I used to have and it was caused by the aftermarket brake pads not being exactly large enough and there was slight pad shifting in the caliper. Being this is a new car and has the OEM pads, I would hope there would be no pad shifting or movement in the calipers.
View 17 Replies
I have a 2012 Rav4 and I have been hearing a creaking/groaning sound coming from the front left brake when I apply it lightly. It gets worse as it heats up. It sounds exactly like the brake in this youtube video.
View 2 Replies
I just replaced my front brake pads and rotors. Car had no squeaking sounds before this. When changing the right front pads and rotor, the set screw that holds the rotor in place snapped on me when I tried to remove it. I drilled out the remaining screw and inserted an easy out / screw extractor to try to remove the broken screw. Screw wouldn't turn/budge and eventually the easy out snapped in half while trying to turn it. Here is where I fear I made a little problem into an even bigger one; I tried to remove the broken easy out by banging the back end (smaller end) of it with a hammer and screwdriver, hoping it would pop out from the front of the hub. No success, and continued using a lot of force to try to remove it from the rear part of the hub. Eventually I noticed the hub area by the back of the easy out bent a little from me using force from the rear to remove the easy out. I stopped there, bent the hub section back to original shape (didn't bend too much to begin with) and sawzawed off the protruding end of the easy out from behind.
After driving a few times I started noticing the squeaking sound coming from the front right wheel, the sound sounds like is in tune/harmony with the wheel rotation. As soon I step on the brakes, the sound stops. I had a similar sounding problem with a rear wheel a long time ago and it ended up being that the bearing needed adjustment. I know the front bearings are pressed in so they can't be adjusted. I am thinking the force used to try to remove the broken easy out damaged something with the hub or bearing or maybe the axle nut.
View 2 Replies
I am having a major issue with my truck. I replaced all of my brakes about 8 months ago. Replaced everything. Rotors, calipers, pads etc. About 3 weeks ago I pushed on the brakes and they locked up and I heard a loud pop and then grinding. I pulled my wheel and my brake on the right rear had broke the 2 mounting bolts and fell off. So I put the brake back on thinking I hadn't tightened the bolts.
Drove about 7 miles and around the 10th time I stepped on my brakes it did the same thing. So I replaced the brakes again. Calipers caliper mount and pads. I have been driving it 2 weeks and all of a sudden same thing happened. I push on the brakes the right rear locked up and snapped the bolts again. So now I replaced everything rotor calipers etc. Greased everything up and no problems for a day. Do I need to replace the brake mount and where do I get that?
View 1 Replies
I know it will wear out the tires but will it hurt the front end? Also the drive shafts to the front end is not turning.
View 1 Replies
For a while my G35 has been making a thunking sound from the front end when either I go over bumps or I apply the brakes lightly at speed. It happens on both the right and left side (i.e. if I go over a bump with my left tire, it happens on the left side, with my right tire, on the right side, etc). Before I take it to mechanic need to determine if it's something I can fix myself.
View 13 Replies
I have a 98 F250LD, its a Lariat, so everything electric/auto. Shift on the Fly 4x4, 5.4, 188K, Factory rear air suspension. Typical Minnesota rust. Anyway, I just noticed in the last 75 miles or so, a drive-line vibration. There is nothing until 39 MPH. Then from 39-41 MPH there is a decent vibration. Stops until 50, then from 50 MPH up it is a steady vibration. I have already changed the u-joints in the rear shaft. I have pulled/wiggled on everything else I can think of with no luck of finding of anything loose.
One thing I did notice, is that the front axle is locked in all the time. How long it has been like this: years for all I know... I can flip the switch from 2wd to 4H and 4L. It all seems to work fine, I hear clicking, the 4x4 engages, the proper lights come on/off. The front axle will pull when supposed to. The transfer case seems to be working fine, but the front axle won't disengage. I am hoping this can be fixed cheaply/easily (DIYer), and also hoping this explains my low fuel mileage.
Front axle? Where to look or what to try and fix for the vibration?
View 2 Replies
On the r32 there is a rattling noise coming from the right rear wheel. It's a very tinny sound and is definitely a metallic noise. The weird thing is as soon as you his the brake, it goes away. Even if you just lightly press on it, it stops. I took the wheel off, looked around for anything loose and found nothing. It's super loud though and completely embarrassing. My e36 bmw does the same exact thing as well and has done so for years, but its much quieter and not as often. On the mkiv its almost constant and at every speed.
View 9 Replies
Was driving issue free most of day, when leaving a red light I noticed my i had to give the van some extra gas to get up and go, then i could feel the brakes getting tighter and tighter to the point where I had to park the van. So currently my van is sitting in a parking lot 30 miles from home with locked up front brakes. Both driver and passenger front wheels were hot to the touch.
View 11 Replies
What would cause my front disc brakes not to work. I have replaced the master cylinder, calipers, hoses and pads. Backs work fine but I can not get good pressure to the front. 1993 f150 5.0 ..
View 1 Replies
I had both front brakes lock up on me the other day and burnt the shoes out so I replaced the pads and installed new calipers and flex lines. I also went ahead and replaced the rear shoes and both wheel cylinders since this truck had been sitting up for the past few years I figured why not. I flushed the system out but I can not get all the air out of the right rear wheel cylinder. My question is could the new wheel cylinder be bad? The new left cylinder blew out when I first started bleeding the right side. I could not get any pressure at all and I looked over and seen fluid pouring out the left side. I put the old one back on only due to time restraints. Should I replace the right side again as well? I have used up 4 1/2 bottles of 3e2 oz brake fluid and still have air in that side.
View 4 Replies
I just purchased a used 2007 Lexus GS 350 AWD. I had it inspected and there were some minor problems (air filter, small oil issue) but nothing big. Driving it, I've noticed that the wheel shakes a little bit when applying brakes and based on my google searches, it's likely a rotor problem. I've literally only driven the car less than 100 miles since it was inspected. Does the inspection place (Tires Plus) bear any responsibility for clearing the inspection on the car? Should I take the car to Tires Plus to look at or should I take it somewhere else?
View 11 Replies
I have been doing my own brakes for years. I have had some that were not easy to keep from squealing but this one has me wanting to get rid of the car. We have a 2008 Dodge Magnum R/T package. Roughly 38K miles on the car. When the car reached around 10K miles the rear passenger wheel would squeal when you applied the brake. Rotor surface was smooth as glass. I took off the rear rotors only and had them turned. Problem went away for about 5K miles. Then the fronts started squealing.
I replaced the fronts because hte factory did not leave any material to be turned and noted that Dodge glued the pads to the calipers like they would never need to come off. Problem went away for a little while. Then it came back with a vengeance. I replaced the pad material on the fronts with ThermoQuiet pads from Raybestos. Problem is coming back again and now I cannot tell which end of the car it is even coming from because it it so loud. My wife drives this car very carefully. My thought is she is polishing the rotors too smooth and this is our source of noise.
We are at the point of squealing again and I am at my wits end with this. If I light foot it, no noise. If I stop like I think it should be stopped, not killing it, the noise is there. If I stop very quickly about 3 to 5 times in a row the noise is gone for a little while until the pads cool and then it is back even if I am on the same journey.
View 4 Replies
So when I got this truck everything on the brakes were messed up. So long story short I got a new master cylinder new pads and all lines are bled. Now this hole time my ABS light has been on so I looked at all the sensors and i found one connector that goes to the rear axle but it has no where to plug into. But I also found some writing on the axle which tells me that is a different axle and may not have had ABS set up. But I am not sure. Now the problem I am having is when I hit the breaks i don't have much bite but if i push on them harder the rear will lock up and the front brakes are biting just a little like 50% power. So how can I get more stopping power to the front pads ? And if its that unconnected sensor is there anyway i can loop in out of the system ?.
View 6 Replies
I have a 99 f150 4x4 that has done this twice, once last year and once this year during hot (90+) weather. I'll notice the vehicle seems like it doesn't want to go. Park overnight and it will work ok. Last time it happened the other day I stopped at wally world and both front wheels were real hot and I could smell the brakes. Came out hour later and when I pushed the brake pedal to put it in gear the pedal went to the floor.
Pumped up pedal and drove off but truck would barely move, drove 10 mph to a buddy of mines shop and it sat overnight and worked perfect the next day. He inspected everything and seems to think it might be the abs control unit. He noticed a small amount of fluid had come out of the unit and dripped on the ground. Also no abs light or brake light has ever come on
View 9 Replies
I have a 1997 Ram 1500 when I apply the brakes the truck pulls to the left for a spit second then goes straight.
Example: doing about 40 MPH take hands off the wheel and slam on the brakes, truck pulls immediately to left, like I did a quick lane change then goes straight.
About a month ago I replaced a section of brake line going to left rear wheel.
View 3 Replies
Bought a high mileage 99 f150 4x4 yesterday. In the process of cleaning her up, the water hose hit the disc brakes on the drivers side and it was hotter than a BBQ grill! Ok, immediately I thought this isn't good. Jacked her up and pulled the caliper. Pads were almost gone so replaced them with a new set, went for a drive. Now the damn things were smoking so bad I thought they were gonna catch fire! Sticky caliper , right? Stopped and got one then realized that the passenger side started doing it too.
Another trip for the other caliper and new pads because these were toast. I mean just burnt to hell. Before I started working on the truck again, I checked on here and I'll be darned if I didn't find out that the old brake hoses might be acting like a check valve because of rust and deterioration. Got a set of brakes hoses too. Put everything on this morning and works like a charm.
1999 4.6 XL
Passenger side done
View 1 Replies
I just bought a 1998 F150 2wd with the 4.6L(no ABS) to be my beater home depot truck. The brakes barely functioned, so I replaced the front bearings, rotors, pads, and calipers. I bled the brakes exactly like I normally do. When I tried to move the truck, the rear tires spun with the front completely locked(also discovered the right rear line had a hole and crimped the line for a moment, but it was the tire that was spinning).
I searched and many people said that bad rubber lines cause the calipers to lockup. I loosened the bleed valves and the fronts were still locked(jacked up the truck and used a breaker bar on lug nuts trying to rotate each tire). I am guessing that it has to be master cylinder or the steel lines. Any tests I could do to narrow down this issue further?
View 1 Replies
