Ford F-150 - 1997-2003 :: F250 - Bearing Noise Is Coming From Front End
Mar 9, 2015
We are working on a 97 f250 light duty 4.6 4x4 5spd. Trying to figure out where a bearing noise is coming from in front end. Replaced both front hub bearings from napa. 150 each... the noise is still there. someone said could be cv shafts... although ive never heard a cv shaft make this noise i replaced them anyway cuz one was clickin last time was in the woods. bearing noise is still there..... in a long bank turn to the left the noise goes away till start to straighten out. while replacing the half shafts I grabbed the plates the shafts bolt to and spun them and checked for slack. none found. front diff's full with no leaks. as title says.... what next?
View 6 Replies
Advertisement
2001, F250, 4x4, 432,000 miles...
Seems this truck eats up bearing assemblies. Its like every 2-3 years, I'm having to replace one side or the other. And we talking like 30-40,000 miles....
BTW.... although I'm not out doing much 4x4 driving, this truck does do a lot of dirt roads, probably over 50%...
View 6 Replies
I have a 1998 F150 with a 4.6 engine and is a 4x4 now the other day when I was backing out of the garage I heard a clunk noise and it seems like it is coming from the right front, so I tried it going forward it made the same noise but not as bad. There is no road noise and all the u joints are good and tight, the noise was when I gave it a little gas. My question is the front cv u joint would this make the noise? And what about the hub? What is the proper why to check the CV joint and the hub? The noise was when I was in 2 wheel drive.
View 14 Replies
I had my front driver side wheel bearing blow on me, out of nowhere, while doing about 70mph on my '03 Supercrew 2wd. it really destroyed my spindle and rotor. i replaced everything from the spindle out (rotor,pad,caliper,caliper mounts, bearings,etc). I packed the bearing really good and put it all back together. Well, it happened again, same thing. Doing about 70 and it just blew out of nowhere. Why it could be happening??
View 14 Replies
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
View 11 Replies
2001 F150 SCAB with 74,000 miles. There seems to be a whistling noise coming from the front axle. It is definately a rolling noise. I can shift into neutral and put it in 4H and still have the noise. Brakes are good, tires are fair... I just rotated my tires (criss-crossed front to back) also sprayed all of my boots with silicone spray. Still has a whistling metal to metal bearing sound. When I have the front jacked up and spin the wheels, there seems to be a decent drag turning by hand. I don't remember having much of a drag before.
View 6 Replies
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 Replies
2001 f150 xl with 151800 miles 5.4l had it for a few years now I get a humming type groaning coming from up front. only when in 4x4 and only at lets say 25 mph to 45 mph .seems to be worse when slowing down especially the slower you get then around 20 or 25 its gone. it is still quite noticeable on acceleration and after 45 its gone. Truck has always been a little noise while in 4x4 weather it was an issue that had already started or if that's how it is. This is my first 4x4 truck.
View 5 Replies
Have a 1998 F-150....heard a strange noise coming from the front passenger side of the truck. Parked and turned the wheel and heard something fall off. It appears to be a shield of some sort.
View 2 Replies
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 Replies
Okay so in my 99 f150 ecsb 4x4 i believe i spun a bearing. its making an awful noise. I was wondering if it was possible to drop the oil pan while the truck is in the air and change the spun bearing. is this possible to do? with 205,000 miles on it...
View 3 Replies
I have a 2000 F150 XLT 5.4L truck. I noticed the AC went out about a month ago and since then I could hear the AC/Clutch bearing making noise. Well I went to start it the other day after eating dinner out and it wouldn't start. It sounds like it wants to start but it just doesn't have enough umph. I replaced the starter and charged the battery up to 100 percent. It still won't start.
If I take the belt off it will start and I checked the AC/Clutch and I can move it with my bear hands. I tried disconnecting the AC/Clutch fuse and relay but that didn't work. Is it possible that the Clutch is freezing up when I try to start it?
View 3 Replies
I just had front and back brakes replaced and there is noise coming from front (I think it's the front)? Any way my brother says its the wheel bearings and that my mechanic should have "caught" that they were bad. I've gone to mechanic for almost 10 years and trust him. Never had wheel bearing problems before so not sure what to think. And if it is wheel bearing can u ballpark cost to fix in Illinois ?
View 10 Replies
I have a 2013 Elantra, new in January, 6600 miles on it, and I took it in to the dealership today because it was making funny noises this week from the left front wheel; the noise gets faster as I drive faster. The left front tire has a bubble in it, and they're telling me the wheel is bent and the bearing is cracked, so they'll need to replace the tire, wheel, hub, bearing and do something with the alignment AND it's not covered under warranty because it is "impact damage." Is this even possible on a new car like this? For the bearing to be cracked without a big accident? I don't remember hitting a pot hole or running over a curb. Shouldn't this be covered under normal use? I'm concerned that I'm being ripped off
View 16 Replies
1998 F250 ld 5.4 4X4 4wabs. The front rotor was seized on THOROUGHLY bearing split apart (outer bearing and bearing "core" still attached to rotor, outer race inner bearing and sleeve still in steering knuckle), the bearing was fine fine until i tried to remove the rotor, any chance it can be pressed back together and saved?
View 3 Replies
My wife's Explorer 4x4 has a noise in the front at around 100km/h. It is not detectable below 90km/h. Its not noticeable from a standstill until around 100, then you hear it a little. I find I can make it more noticeable if I vary my speed from 110 to 105 up and down, then its easier to hear. Once you get below 90 km/h you cant hear it at all.
I have a broken leg right now, and I normally do ALL my own work so I'm a little-limited mobility wise at the moment.
I'm suspecting a wheel bearing. I put the Explorer in the garage and my son jack up both wheels on the drivers side. I started the engine and SLOWLY accelerated up through the gears to 100. I know the hazards with this as I've done it with other vehicles, but this was the first 4x4. Then we jacked up the passenger side (after lowering the drivers side) and did the same thing. I could slightly hear/feel the rumble when the passenger side was jacked up.
I did drive the vehicle on my outdoor ramp/pit so I could use my crutches and get underneath to have a look. I grabbed the cv axles and they feel solid. The propeller shaft was replaced last year, and the cv axles look brand new. (bought the vehicle off a friend two years ago.).
So, are my suspicions correct, is it the pass. side wheel bearing? The Explorer has 294000kms. Never did test it on corners as I didn't want to swerve back and forth on the highway with the amount of traffic.
View 4 Replies
I have a bad wobble/vibration coming from front end i think i replaced hub locking hubs u joints truck dont feel safe at all took it to ford they say its normal no way its not just starting doing it few month feels like the 4x4 is in use when hitting bumps when driving if you go slight left or right it seems too make act up more.
View 2 Replies
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 Replies
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies
I have a 2002 F-250 7.3. I was driving home from work on Tuesday (highway), I heard an intermittent noise coming from the front end, sounded like a rubbing/grinding noise. Yesterday on my way to wok, same thing, on and off. Yesterday on my way home the noise was constant, didn't go away. The noise comes at about 45mph and stays until I'm back under about 45mph, so mainly just on the highway. I put the truck in neutral and let off the pedal and the noise is still there which tells me it isn't engine related.
Yesterday after work I jacked up the front end, spun the tires, no noise. No play in the tires top/bottom or side/side. Took the tires off and what I did notice is the right axle u-joint is shot. I am hearing the noise in 2wd so I don't know if its the u-joint that's making the noise. Could it be a bad wheel hub bearing? Is it the u-joint? Maybe needle bearing??
View 6 Replies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 Replies
