Ford F-150 - 1997-2003 :: Exhaust Leak Cause A P0171 Code / Idling Rough And Almost Stalling At Red Lights
Jan 13, 2014
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
View 14 Replies
Advertisement
My daughter returned from college with her 2000 f150 4.2 idling and running rough on acceleration. It is throwing a P0171 code only. I replaced the isolator bolts/plenum gaskets four years ago because of a P0171 & P0174 codes.
So far I have replaced the MAF, new PCV valve and elbow, checked all obvious lines for vacuum leaks (though I suspect a leak somewhere still). Also, a quick check of the plugs show some lean color/deposits on the drivers side only. Any thoughts or troubleshooting I should try next?
View 6 Replies
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
View 2 Replies
97 F150 4.6 Vin 6, 5-Speed Trans, 200,000mi, Rebuilt recently. I was on my way to get my truck smogged, but she threw a code, P0171. I read somewhere to clean the throttle body elbow, which I did (needed to do it anyway). After I had everything put back together, I start her, and it's rough and immediately dies. If I keep the RPM's at about 1.5k for a minute, then let off, the truck will run fine for about 30-45 seconds, then die again. I just replaced my IAC and the problem persists.
View 8 Replies
I recently got a 2wd 1994 150 straight 6 4.9L, It's been a great truck so far. It drove from New Mexico to California with no issues. Just this morning it started stalling and dying when pulling up to stop lights and putting it in reverse. The truck has 172,000 miles and has a new serp belt, alternator, radiator, and starter. It seems to run just fine on the highway and once it's warmed up it doesn't stall as easily. There is an exaust leak.
View 1 Replies
I've got a 2000 f150 with a 5.4 and 135,000 miles. The other day it was driving fine then i stopped and got gas and after that it was boggy and running rough so i thought bad gas but i ran through that gas and got more at a different store. The cel came on i got it checked it was misfire cylinder 1 so i put new cop, spark plug, and injector. Unhooked the battery and then the light came back on so i ran the code and now im getting a p0171. I checked the pcv and sprayed around the intake and vacuum lines. I also checked the pcv hose and elbow in the back and i found nothing its a fairly new hose. So, it does run rough it shutters a lot.
View 2 Replies
I have a 2000 Ls 3.9 V8 125,000 miles that started idling rough.I checked for codes and got p0171 (bank 1 lean), p0175 (bank 2 rich) and p0307(cylinder 7 misfire). I swapped cop and sparkplug from cylinder 7 to cylinder 5 and erased the codes.I ran the engine for a while and rechecked the codes to see if the misfire followed the cop and plug. They did not. I still get p0171,p0175 and p0307 (cylinder 7 misfire).
View 7 Replies
I just purchased a 2003 V10 with 270 000kms. The truck had had regular maintenance. It has an exhaust leak and runs a little bit rough. Could the exhaust leak cause the truck to run a little rough or am I dealing with another issue?
View 2 Replies
I have a 2003 F150 4.2 with 155000 miles. What may be causing this?
View 6 Replies
I've had this problem for a little while now, my 97' F150 V8 4.6L, has been running real loud and heavy. When it starts up it sounds like a race car. It finally shot me a code for P0171 - Bank 1 (passenger side) running too lean. From what I've read, this is most likely a vacuum leak but I don't know too much about it.
A couple of things I've noticed while driving it around:
1. If you are in the engine compartment while its running, you smell the excess gas on the passenger side of the truck.
2. The exhaust also smells really heavy
3. The loud and heavy running is mainly when accelerating, if I maintain a constant speed at for a little while it almost starts to run normal. Cruising down the highway its almost just as quiet as before the issue
4. Engine coolant heats up much more quickly, but doesn't get above operating temperature (read from tuner, never above 200 degrees)
In response to the problem I replaced both the O2 sensors closest to the engine and the PCV and elbow. No change. Have a fuel filter ready to install, but for some reason I don't think that is it either, as it would probably effect both bank 1 and 2.
Like I said I'm not too well versed in the vacuum system but if any of these symptoms stand out I'd love to hear your thoughts.
View 2 Replies
The "service engine soon" light on my 2003 F150 Supercrew 4.6L (225k miles) just came on. The code it's throwing is P0171.
View 3 Replies
1999 xlt with 5.4 lt p0171 only. it started with what felt like a misfire or hesitation and rough idle. Extremely rough at 40-45 mph. but with no misfire codes just p0171 so all 8 coils and plugs and sparks replaced twice in one month. and still same code tested fuel pump pressure 28 psi.... removed clogged cats, still same code... new pcv valve and elbow.... checked for air leaks around intake and intake manifold and nothing.... cleaned mass air flow sensor...I can unplug any coil on bank 1 and it wont make a difference. But if I unplug any bank 2 coils and engine makes a difference.
View 2 Replies
I am still battling a p0171 code on my 2000 f150 5.4. I checked the fuel pressure at idle it sits at 31. I remove the vacuum line off the regulator it goes to 41. When i give it throttle when in gear it will maintain at 30. And when I shut the vehicle off completely it will maintain 38. Just looking to see if this is correct numbers. I was trying to determine a weak fuel pump.
View 9 Replies
97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
View 4 Replies
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 Replies
I have a 2000 f150 with 5.4 Triton with 165k miles. I did invest in a code reader. It started missing and code P0302 came up along with P0171. Put new coil on #2 and truck ran fine for a few days. Then it started to run rough again. Shaking, Idle rough, no power and CEL came on again. This time code P0171. I changed out fuel filter to no avail. My next step was to start looking for vacuum leaks. As I'm searching, All I am finding is trucks with this problem also get P0174 code. My question is since I am only getting lean on one bank does that pretty much eliminate things like MAF or the famous elbow vacuum leak and make something that only affects one bank like an O2 sensor on CAT more likely?
View 2 Replies
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 Replies
My 03 with a 5.4 has been hesitating a when you accelerate and cutting out as well as idling rough and die when you slow down. It does all this intermittently. Not every stop or every time you accelerate. I first got a code for the MAF and both banks running rich (PO102, PO172, PO175) so I cleaned the throttle body and MAF. The running rich code came back (PO172, PO175) so I then changed the MAF and air filter . It seemed to work for a day or so then my light came on and I figured the same code was back but to my surprise it was now both banks running lean(PO171, PO174) so I took my MAF back and got another one. It hasn't set a code yet but it is still running poorly. I have changed all the COP's and plugs as well ....
View 13 Replies
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
View 8 Replies
Where the cabin air intake location is? I'm not talking about the air filter.
My 97 F150 has some sort of exhaust leak and it's coming into the cabin when the heat is on. I want to tape up the cabin air intake port but I don't know where it is. On later models, it's on the right passenger side near the cowl of the hood. Where is it on the 97?
View 2 Replies
