Ford F-150 - 1997-2003 :: EGR Tube / Manifold Leak
Mar 12, 2012
So I've driven my 97 F-150 (4.6 L) around for several months now listening to that wretched left side exhaust leak caused by the nut on the EGR tube rotting off the nipple on the manifold. I tried plugging it, taping it with that exhaust "bandage" tape, etc. Nothing obviously ever lasted. And I sure didn't want to try replacing the manifold and then dealing with the potential broken studs, etc.
Then I finally got around to getting the gas tank straps replaced with that recall. So I took it to the dealership this past Friday. I mentioned the EGR tube leak kind of in passing. The service manager said they could fix it for about 80 bucks. He said they had successfully removed quite a few of those nipples without replacing the manifold. I kind of thought to myself "yeah right" (considering I live in the rust belt with all the road salt, etc.) and told them to go for it.
Not surprisingly, they called me back later in the day and said they couldn't get it out, and he wants to replace the manifold, etc. I just told him to plug it instead. When I picked up the truck, I learned the mechanic decided to WELD it instead of plugging it. I was pretty surprised that he tackled it, and he actually did a pretty decent job in sealing it except for one small pin hole on the back side between the welds. I mixed up some JB Weld and filled the pinhole. The welds may fail or the JB Weld blows out tomorrow, but, in the meantime, I don't have to listen to that wretched exhaust leak constantly. At least I'll have a few days peace if not longer
View 14 Replies
Advertisement
I have a minor leak at the base of the trans dipstick tube. I assume that the tube is press in ? has an o-ring ? I put some silicone around the area and that worked about a week, the fluid is probably eating through that type sealant. The trans is a 4r70. Seems to me that the actual tube should be ok and having never dealt with replacing one I want a little advice before yanking it out.
View 11 Replies
So I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
View 8 Replies
My 2003 f150 4x4 w/5.4 has 220k miles and only minor issues until a few days ago. I now have a coolant leak at the mating surface (both sides left and right) of the aluminum crossover coolant manifold (holds thermostat on one end). I have most of the bolts out to remove the crossover manifold but there is one bolt on the RH side that comes from the underside. All things equal, main question is... Can that crossover mainfold be removed independently from the intake? My thought is that in order to get to that last single bolt (there may be others I am not aware of yet) that I will need to remove the intake.
View 1 Replies
I've got a 1997 F150 with the 4.2L V6. Before I got it last summer I did some research, but apparently missed the issue with the intake manifold gasket leaks on these early engines. It seems to be a very slow leak, but obviously I want to get it fixed. I called Ford to see if it had had the recall work done on it, but all they could tell me is that there wasn't an open recall on my truck (with the exception of the recent fuel tank strap recall). Their system apparently only goes back 10 years, so they couldn't even see the freakin' recall. So, I've got a few questions:
1) I know I didn't post much info, but does this seem like an intake manifold leak?
2) Are there any special tools needed to change out the gasket myself?
3) Can you all recommend any replacement gaskets? I found a few different manufacturers of gaskets, but I'm sure some are better than others.
4) Can this issue cause the computer to throw the loose gas cap code (P0455 if I recall correctly).
5) Would it be worth it to just get a new truck? I really wanted a diesel in the first place, but I also hate to give up on a nice truck with only 115,000 miles.
View 6 Replies
I have a 2001 F150 Super Crew 5.4. I had a leak where the water transfer connects to the intake manifold. I decided to get a new manifold rather than trying to repair it. The new manifold from Dorman came and the gaskets were built into the manifold. I torqued the manifold to specs. I replaced everything and it starts fine.
I can hear what sounds like a leak, but can't find anything. I checked every hose that is connected and they are all snug and connected. I had the check engine light checked and it said it was running lean on both sides (p0174, p0171). Also a p0122. I thought something might have damaged the Throttle Body Position Sensor, so I replaced it...but no change.
I'm still driving it everyday because I need to. It won't change gears so smoothly sometimes. The most noticeable problem is that the A/C doesn't work. It just blows hot air. And the worst part about it is...it does it even when the air isn't turned on! I just go around with the windows down...in 95+ degree heat...with hot air blowing!
This is my first time to attempt a manifold change out. What I should check?
View 4 Replies
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies
I had a leak at the flange several months ago. I fixed it with the diesel o rings kit. I made a trip from TX to AL with no leaking and drive it daily without leaks. But, 2 weeks ago noticed a small dribble of a leak from the same spot again - not enough to leave a mark on the pavement but any leaking drives me nuts. I applied some RTV. It worked for the 2 weeks.
Today, noticing another dribble of a leak coming through the RTV down the pan. I'm thinking the flange is bent and not keeping that o-ring sealed against the pan. I'm going to try to apply some additional RTV at the leak spot. If this doesn't work? Is that Strictly Diesel adapter really worth that kind of dough? Is pushing the OEM adapter into the pan really acceptable? Any other options?
View 14 Replies
So after a hot drive yesterday we thought to do some googling about our clutch cycling on and off so fast. Yep, the airgap was out of spec. Fixed that.
Then we added some refrigerant to the truck. The truck is "new to us" and this is our first summer with it so not sure what might've gone on previously with the AC. Didn't take long to find a rather sizable leak. :P
See that metal tube going into the "spongy" area? Yeah, that's where it seems to be coming out. That tube is the only one that's cold, the rest are ambient temp. We fix a lot on our jeeps, but the AC system is naturally a bit out of our wheel house since it's not something you normally tangle with. Is this an easy fix? Or do we need to take it in to get serviced?
View 12 Replies
Rusted dipstick tube I thought was going to be an easy enough fix. Broke off clean at the block. Tried for hours, easy out, prying, vise grips anything I could think of. Well I tried to pry the side of the tube over to make room for my needle nose vise grips, and boom. Down in the oil pan it goes.
Do you think theres any way possible I can fish it out through the drain plug. I really dont want to pull the darn motor.
View 7 Replies
1998 F150 4.6L. Pretty sure EGR is bad. Clogged ports cleaned, DPFE changed, etc. Tried the suck test on EGR, no change. Still getting 401 code. Ports were really bad, so I figure EGR is clogged/bad also.
Here's the problem....I can't get the nut loose that holds the tube from the manifold onto the EGR. It is on the back side of the EGR facing the firewall. Not a whole lot of room to work with, but I can get a 1-1/16 wrench on it. I have tried soaking it in PB, heating the EGR body with propane, beating on it with everything I can find, and it still won't budge.
If I unbolt the EGR from the TB, I have no leverage on it.
View 3 Replies
I need a front axle tube for a 1999 F-150 4x4, I have tried local parts houses and dealership with no luck. Any information where I might locate one.
View 6 Replies
I got a 97 F250 4x4 w/ 4.6 lt. motor & auto trans. The engine is leaking oil. It looks to be coming from a set of hoses that are on the adaptor that is between the oil filter & the engine block. Also what are the oil lines called? It is leaking motor oil not transmission oil.
Also just pulled my oil dip stick & the whole thing (dip stick & the tube) came off the truck. Seems the tube has rotted away at the oil pan. Is this also a job I can do?
View 6 Replies
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
View 14 Replies
Ok, I have a 98 F150 XLT, standard cab, 8 ft. bed, 2WD with limited slip - if any of that makes a difference.
The rear axle vent tube is literally blowing oil out the top, where it's loosely connected to the bed. It does this every few weeks. I pulled the hose and ran a rifle cleaning rod down it to make sure it wasn't plugged ... it wasn't.
It seems like it's building up pressure somewhere, then blowing all at once, but why?
View 13 Replies
Ford F-150, 1999, 4WD. My dipstick tube has rusted off right at the point where it attaches to the engine block. I purchased a new one but I'm not sure if that's a job I can do on my own. What installing a new tube will entail?
View 5 Replies
2003 F350 short bed 6.8L V10---On start up a slight tap sound, almost like a cranky lifter, but it is an exhaust manifold leak. At the bolts, I am not sure. This has been this way for 5 years, no better no worse. After I run about 2 to 3 minutes it seals itself. Not a hint of noise. Due to heat, something is expanding to seal it (aluminum).
At my annual PA. State Safety Inspection the Tech says 'that has to be corrected if it worsens', but It does not fail inspection. This puzzles me.
How is the call made for correction. A flip of the coin, a guess and is it serious enough to fail inspection. Is this normal with the 6.8L or V10s. I know the cost involved for a fix is big league, but can it be justified. TRUCK RUNS GREAT !---
View 4 Replies
I am changing the passenfer side exhaust manifold on my '00 150. The bolts all came out fairly easy, sprayed them often in PB over the last 2 days, my problem is the 2nd and 3rd nuts on the bottom are under the motor mount. Do I need to remove that or is there an easier way that I'm missing.
View 11 Replies
So I just installed a fresh 4.6 long-block in my '98 4x4 xlt and I have a noise coming from the manifold area. Thought it was possibly valves or timing chain. Took it to dealer and they diagnosed it as the Intake Manifold Runner Control. Never heard of it!!! Problem is, I can't find that part for this motor. Is it inside the intake? Do I have to replace the whole intake? Dealer didn't tell me, once I said I would do the work myself.
View 3 Replies
Replaced head gaskets on 2003 f-150 5.4. Now I can hear a ticking noise in middle of intake by #5 port. Maybe timing is off 1 link?
View 4 Replies
I have a 98 F150 4x4 Super Cab 4.6 auto that has a leaking exhaust manifold. I changed both manifolds about 3 years ago and the passenger side bank is leaking again. I haven't gotten into yet to see if its just the gasket or the manifold itself. My question is does anyone know of a set of headers I can put on the truck that will bolt up to the existing exhaust? If I make the switch to headers I don't want to have to redo the whole exhaust system.
View 3 Replies
