Ford F-150 - 1997-2003 :: Code P0161 Came Up - 2nd Bank Downstream Heater Circuit Fault
Jun 30, 2015
Just started the truck after not running for a few weeks and drove around fine. Looked down and suddenly a CEL was indicated. Checked it with my Edge Evolution diagnostic mode and Code P0161 came up 2nd bank downstream heater circuit fault. I've also have an exhaust leak in the right passenger side exhaust manifold for about the last year. I've been waiting to install my newer 03' used engine when time and funds permit.
View 3 Replies
Advertisement
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 Replies
I have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.
View 1 Replies
Light did not come on for a while then it finally did. I replaced all plugs & that did nothing, almost made it worse. Put a scanner on it & it reads bank one lean, misfire. i unplugged all the coils one at a time on the drivers side & didn't notice any drop in rpms. On a side note, the exhaust leaks a bit of water out of the tailpipes a bit at idle.
View 3 Replies
1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...
I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?
I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?
I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...
View 5 Replies
Well I got the ubiquitous "Bank 1 Too Lean" code this morning. Yesterday I changed out the PVC Valve, Elbow and Hose assy.
I changed out the hose from the intake to the canister purge valve on the firewall next to the master brake cylinder, that one was like dust.
Today I'm changing out the rear O2 sensors, but I may change out the fronts when they get them in (very rural area hear).
I'll keep looking for vacuum leaks and change out the MAF sensor. I hate to think it may be the intake....
View 11 Replies
I have an emissions test coming up. I have 3 P codes that I'd like to eliminate before then. I don't want to "fix" the issues they are telling me about. Just make the codes go away. I know why they're there I just need to get rid of them.
What I have coming up is:
P0475 Exhaust Pressure Circuit Valve (result of EBPV delete)
P0541 Intake air heater A circuit low (result of aih delete)
P0640 Intake air heater control circuit (also result of aih delete)
What resistors I'll need and where to put them in?
View 12 Replies
So my truck is reading a code at P0172 which means bank one is too rich. I replaced all of my o2 sensors, cleaned my MAF, and replaced PCV and hoses connected to it. What else could it be?
View 3 Replies
The p0340 code is the cam position right? Ready says bank 1.. Is there 2? Where the bank one is? And do I need to get on tdc on cyl one first or not?
View 3 Replies
1997 f250 LD pick up 5.4L engine 131000 miles
Here is my story week ago code came on p0153 bank 2 sensor 1
Slow response ... now I been reading around and some people say bank 2 is passenger side other say it is drivers side or bank 1 is where cylinder 1 is , the point is I'm confused here for bank locations and sensor locations .....
View 3 Replies
I am in the process of trying to chase down a vacuum leak on my 2003 F150 with the 5.4. I have checked all lines and cannot find it. I decided to check the long term fuel trim and noticed that my bank 1 is slightly higher than bank 2 (screenshot attached). Is this enough to assume the leak is on the bank 1 side?
View 14 Replies
I've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......
View 7 Replies
I need the PCM pinout for a 2002 F150 4.6 For the Purge Control Valve Circuit. If possible the wire schematic would be nice also. Getting code PO443 (( hard code )) I have checked battery voltage at valve connector with key on (( 12.2 volts )) valve resistance is at be 35 ohms so I'm thinking I may have a bad wire or a bad PCM .
View 2 Replies
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 Replies
I'm pulling a P0403 EGR circuit fault on a 2004 v6 Escape.
Last night I changed out the EGR solenoid. Cleared the code and drove around for a while, got on the highway and cruised for a few miles and everything seemed fine. Turn the car off and back on and the code showed up again.
My next step will be to check the electrical connection to the solenoid. I don't do a lot of auto repair.
With my multimeter I will check for 12 volts. But from what I understand I can not check ground as the PCM sends ground to the solenoid to activate it. How should I check the electrical connections to the EGR solenoid?
View 3 Replies
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
View 3 Replies
I have have been getting a p0671 fault code every time I start my truck now that its cold. If I clear it and its warm it doesn't retrigger at least until it sits overnight again. Is this likely to be that the Glow Plug needs replacing on the #1 cylinder? Autolite Glow Plug is only $20 or so. Mechanic is recommending changing the bank and the harness but I'd rather just do the one GP myself if possible. I see on here that the valve cover has to come off. Which side is #1 on and do I need any gaskets etc? How big a job is it to remove the valve cover? I'd go and look myself but its cold out ...
View 1 Replies
On a family vacation in our 2013 6.7 pulling a 41ft trailer to the Seattle area from Alberta Canada. Made it to destination yesterday. Woke up this morning started truck and cel on. Bought a code reader at the local napa store and read P206 fault inj 6 open circuit. Any thoughts on driving the truck around with a inj fault? Thought I had read here some where that 6 was the regen cylinder.
View 14 Replies
Where to decipher engine codes? I pulled a P0001 Fuel Volume Regulator Control Circuit Open code .
View 11 Replies
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 Replies
1997 2wd, 4.0 - As you can guess it runs pretty bad at idle. It has O2 heater circuit codes for all 3 sensors. I'm leaning towards the ECM because the 2 heater wires are both hot with the key on. I unplugged the computer and turned the key on and just one wire is hot. Looks like the ecm is supposed to ground the wire to turn the heater on, but it's going hot instead?
View 14 Replies
