Ford F-150 - 1997-2003 :: Clunk When Coming To A Stop
May 3, 2004
I'm getting a CLUNK when coming to a stop with my truck.
If I shut off the overdrive while coming to a stop it doesn't do it. Or if I manually shift it down a gear.
I read on here it could be a U-joint or the yoke or something and maybe something needs greased.
Anyway I crawled under the truck and it looks like I need a special socket to remove the 4 bolts holding the driveshaft to the rear end.
What type of socket it this? No grease fittings on my U-joints. What's causing this CLUNK as well?
View 14 Replies
Advertisement
My 2002 F-150 with the 5.4 has an issue with a high rev (1000 RPM for a few seconds) while at a stop sign, along with a clunking/banging sound coming from under the truck. This is when I have the brake mashed all the way, and this all happens at the same time, almost every time I come to a stop at a stop sign or light. I do have an intake manifold leak, which i have recently determined, but I do not know if the high rev at a stop sign has to do with the manifold leak or to do with the transmission sounding thump I hear. Could this be a torque converter not unlocking, and then suddenly unlocking? Because after the thump sound, the RPM's go down to around 650 from 1000 every time.
View 4 Replies
I have a 1998 F150 with a 4.6 engine and is a 4x4 now the other day when I was backing out of the garage I heard a clunk noise and it seems like it is coming from the right front, so I tried it going forward it made the same noise but not as bad. There is no road noise and all the u joints are good and tight, the noise was when I gave it a little gas. My question is the front cv u joint would this make the noise? And what about the hub? What is the proper why to check the CV joint and the hub? The noise was when I was in 2 wheel drive.
View 14 Replies
I've recently had problems with my truck running 97 f150 4.2L.The latest episode is it stalling when coming to a stop. It will start right back up, I've checked for codes and found none, I have changed the fuel and air filters and I have tested the fuel pressure.(I have a video of the test however I don't know how to upload it.) Key on engine off it pumps up to 30 immediately on the gauge. key on engine running gauge shows a steady 32. I am really at a loss for what to check next. I really need this truck dependable again ASAP my wife is scared to drive it.
View 11 Replies
I have a 2000 f150 with 210000 miles. The truck wants to stall when coming to a stop. I have noticed this from a higher speed and more when at operating temp. The truck runs great and idles at a stop great, but when coming to the stop the rpms drop to300 or so then it catches itself and revs up. I have cleaned the maf sensor the iac and checked throttle body all seem to be in working order and no obvious vacuum leaks.
My power steering pump is going and it's time to change plugs, but don't believe these would only effect the truck at braking. Have heard maybe torque converter is stuck this does make sense cause usually happens after getting out of first gear. Would changing the fluid solve this or should i look at sensors? Fluid starting to turn slight brown probably been in there 80000 miles.
View 3 Replies
I have a weird problem that just started concurring. When you approach a stop and the vehicle is almost at 1 or 2 MPH, the pedal pulses and I can hear the ABS buzzing. None of the wheels are slipping, and all my tires are of the correct size & pressure. There is no ABS codes at all. There is no ABS light on either. How can I diagnose? 2004 Heritage.....
View 2 Replies
I have a 1999 f-150 4x4 4.6 5spd manual 180,000 miles on the clock. My question is, when coming to a stop i push the clutch in an the idle hangs at about twice what it should be until i come to a complete stop then it drops to normal. It's not like somethings sticking cause it will stay at the high idle as long as were rolling but as soon as the wheels stop turning it drops down.
View 2 Replies
I have a 1997 F250LD 4WD. I was driving and came to a stop light. I hit the brakes and the pedal was rock hard with what seemed to be very little travel. I pushed hard to get to a stop and the abs activated and I came to a slow stop. This has happened about 3 times over the last 1000 miles of driving. I see no ABS or Engine lights. Most of the time the brakes are normal. Pads are fine, fluid is fine. Brake booster seems to work fine, pedal is not mushy or hard to press other than the 3 or so times this has happened. Once this happens I can let off the brake and everything is normal. I have not found any vacuum leaks.
View 6 Replies
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
View 3 Replies
Car that would go clunk after coming to a stop. (don't recall the type of car) It sort of reminds me of what my car will do on occasion. Sometimes after coming to a stop for a few seconds my car's A/C compressor will kick on, kicking up the idle speed of the engine. From time to time I can hear my rear brakes grabbing harder as the car attempts to move forward because of the idle speed increasing. Could be that's what he's hearing also.
View 15 Replies
Every once in a while, while driving my 06 350 SRW at slow speeds, I hear a grinding noise coming from the left side of the truck. It is almost like a winding grinding noise if that makes sense. It will grind slow to a stop, and then I hear a clunk.
This is a very intermittent problem. The tires are completely shot on the truck, and I thought that would be it, but considering it is intermittent and the clunk I hear as I come to a stop I figured it could be it.
View 4 Replies
Lexus IS350 ... Noticed a reasonably quiet clunk from the car when coming to a stop? It happens when the transmission automatically shifts into 1st gear with your foot on the brakes.
I noticed that in my car, you can feel a slight lurch forward as the transmission downshifts into first when approaching a stop sign. If I am barely on the brakes, I feel the slight lurch but don't hear anything. Under normal braking, that slight lurch happens along with a clunk. You wouldn't hear it with the radio on, but it's very repeatable and with the windows down you can hear it as well coming from under the car somewhere.
View 13 Replies
Or just can I just replace and go. I'm having some issues with trans on my 06 gs430. It's having a downshift clunk/jerk when coming to a stop. I just purchased a used trans, but would like to see if it could be ecu related. I have seen other comments from other member that they replaced the trans, but still the issues were present. Some stated that there was some issues with the ecu holding the trans solenoid longer then the usual.
View 6 Replies
My 2007 Sonata V6 limited would produce a pop / clunk sound (sometimes 2-3 in succession) under these circumstances
- Car is coming to a stop (brake applied)
- When I release my brakes, press on the accelerator, a pop / clunk sound would ensue
It doesn't happen all the time. I noticed it's more prevalent when it's hot outside or when I've driven the car for a little bit
My mechanic re-tightened the subframe bolts and visually checked bushings / ball joints but everything seems tight.
View 6 Replies
2010 SE 4Motion: My Tiguan's tranny seems to clunk pretty bad when coming to a stop. Wasn't a problem until after I got flashed to APR stage 1 so it may still be adapting, but I'm not sure.
View 10 Replies
I am the new owner of a 2007 Lexus GS350 and I absolutely love the car. 70k miles and it has been well taken care of by the previous two owners. The question I have is regarding a strange subtle jerk when coming to a stop. This seems to be the most intense with a medium force stop but I can also feel it when coasting to a stop. It happens frequently and sometimes is less harsh than other times. I noticed it right after picking up the vehicle but I didn't really pay much attention. After driving the car for 2 months I notice it more. The jerk seems to be happening during downshifting and is at about 15 mph every time. It's not extreme but passengers typically notice it if I point it out. Then they can feel it every time it happens. The other shifts are smooth including accelerating and so forth. I reset the ECU (pulled the ETC and EFI2 Fuses) about two weeks ago but haven't noticed a difference in shifting.
View 14 Replies
I have been reading some mixed reviews here in regards to the "CLUNK". I am referring to that feeling as if hit from behind shortly after coming to a stop. Some are saying it still exists in the 2005 while others are implying that it has been resolved.
Just to be perfectly clear.... Has experienced this "Clunk" in a 2005 GX?
View 14 Replies
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
View 2 Replies
All right, I went ahead and rebuilt my suspension considering everything was worn out. I used upper and lower control arms and all the tie rod ends from O'Reilly's (MasterPro). While I was under there I noticed that the sway bar end links and bushings were deformed and worn, so I changed those out.
The clunky front end is confusing as hell to me. All of the front end bushings and ball joints are new, and if I hit bumps with a little vigor it rattles. Under hard braking to a stop there is a loud clunk from the front left. I have shocks on the way (Monroe Reflexes for the front, Sensatrac load adjusters for the rear), which are the only things left that have been removed and not replaced with new ones.
The truck was perfectly clunk and rattle free with the old worn out bushings and ball joints. I can't imagine why it would start clunking now with a new front end. I felt the new ball joints and they were tight and didn't have any play. The bushings were tight. I'm at the end of my rope with this crap. I've double checked that the ball joint and chassis nuts and bolts are all very tight.
View 7 Replies
I have a 13 Altima and have been hearing a clunk/pop sound when coming to a stop and sometimes when changing from park to drive and park to reverse. It seems to also be there when accelerating too and the car is also seem to be vibrating when moving at lower speeds. Today i noticed something else. I parked the car and took the key out. I went to the side of the car and slowly rocked it back and forth and started to hear this clunk sound. I have uploaded it to youtube and can be found here [URL].... . After hearing the sound, I decided to take the driver wheel off and noticed it makes the same sound when i move the tires. It seems to be coming from the CV joint, where it connects to the transmission. why would a car make that clunk sound with the car/key off and swayed back and fourth? does this seem like a CV joint issue or something related to the transmission.
View 3 Replies
I have a 97' f250, 4.6L auto transmission, 4x4, 168000.
I have only owned the truck about 5 months so I dont know much about the history. When I coast to a stop, (usually 40mph or faster) to a stop I get a clunk on the down shift into second I believe. It only happens when coasting to a stop, all other shifting up and down patterns are good. This happens I would say 7 out of 10 times but seems to be increasing.
The other issues that I believe is related happens every time I put the truck into reverse, there is a similar clunk. This happens every time and does not do it into drive.
I have ran lots of searches related to this in FTE, I cant get a clear direction to begin down. It seems like it could be transmission related but also may be driveline or U-joint related.
Two other notes-I did drain and replace the transmission fluid and I noticed that the T-case and transmission are much cleaner than any other undercarriage part. Whatever that means??
View 8 Replies
