Ford F-150 - 1997-2003 :: Chirping Noise From Driveshaft Area
Jan 31, 2011
I have a 99 F150 4x4 4.6L automatic trans. The truck has 260,000 miles on it. Saturday, while going down the interstate, this chirping noise started up from the rear. When I got home I jacked the rear up and spun the wheels while listening. There is a chirping noise that, as best as I can tell is coming from around the front of the driveshaft around the u-joint area. I've never known of a u-joint to make this type of noise before. There is no vibration or anything, just the noise. The frequency of the noise increases and decreases as I speed up and slow down. I don't think it's coming from the transmission, but it's hard to tell, as everything echoes. I couldn't imaging the driveshaft itself making this noise, but I guess it's possible.
View 12 Replies
Advertisement
I own a 1999 F-150 V6 4.2 and would like solving what sounds to be a chirping noise coming from the engine. Noise is pretty consistent at which occurs at first startup while in park, drive or reverse and definitely every time I hit the gas from a standstill. The noise is pretty faint but bothers me just enough to where I want to ask the experts. Anyway noise began roughly days after I washed down the motor. I sprayed some degreaser on it and was very careful - making sure to cover the fuse box, alternator and high flow k&n intake air filter.
I stayed away from cables and just used a garden hose. Recently I had the lower idle pulley bearings replaced, serpentine belt and alternator. When I took to Ford for a new belt (it was old) and to inspect the chirping noise, they said # 6 spark plug was loose and that was the reason for the chirp (they called it a ticking noise). First of all how does a spark plug just come loose? They hand tightened it back and I drove the truck for less than a week then the noise was back. Any possibility this sounds like something specific that is wrong? My research says that it could be anything from the belt tensioner to the cam sychronizer to the heat shield around the cat converter.
View 2 Replies
Can I do this without damage to anything?
'97 Expedition (but the F150 forum seems more mechanically incline, no offense to the Expedition forum).
I'm trying to find the cause of a vibration in what I think is the front drivetrain. I was almost positive that it was the front driveshaft universal joints. I jacked the truck up off all fours and took her for a spin. The noise seemed to be coming from the from u-joint.
I took the u-joints off and they were still nicely lubricated (after 230,000 miles). My heart sank since this probably not the root of my problem.
I'm surely going to put new u-joints in but think I'll get them from the dealer tomorrow (if the OEM stuff lasted this long, why buy aftermarket, even though it's the same stuff? I dunno, just my OCD kicking in.)
So, I thought I would take the truck for a drive without the front driveshaft today (in 2wd of course) to see if the vibration was gone. Can I do this?
View 6 Replies
I have 1997 F250 LD since i bough it has been doing this chirping sound coming from the serpentine belt and the pulley area but when the truck has been working for 15 - 20 min it goes away
This is apart from the from the problem before I think the fan clutch is broken because when I start the truck I can hear the fan going at the same speed of the engine is that normal ? even when the truck is cold
View 3 Replies
What the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 Replies
So I just installed a fresh 4.6 long-block in my '98 4x4 xlt and I have a noise coming from the manifold area. Thought it was possibly valves or timing chain. Took it to dealer and they diagnosed it as the Intake Manifold Runner Control. Never heard of it!!! Problem is, I can't find that part for this motor. Is it inside the intake? Do I have to replace the whole intake? Dealer didn't tell me, once I said I would do the work myself.
View 3 Replies
2000 f150 supercab 4x4 offroad. Sometimes in a very strong wind, I get a lot of air noise around the doors which is up in the window area. I occasionally get it if I haven't got the back half door shut tight.
Just wondering if there is a way to puff up those door seals without replacing them? Inject them with something or use a hair dryer to heat them?
View 14 Replies
I've got sort of a howl going on, was thinking rear end, but when i jacked up the wheels and spun the driveshaft the noise seemed to come from the transfer case area. I haven't had a chance to check the fluid yet, could it be a bearing in the t-case? Its only when i'm on the gas if i let off its gone. 2001 f150 super crew 4x4
View 4 Replies
2000, F-150, 35K +original miles. 4.6L V8
Some weeks ago a noise started that sounded like fan blades striking against heavy plastic fan guard. At first I thought it was coming from the transmission/Transfer case area but after a few weeks of listening to I now believe it's coming from behind the dash area, however, I can't find any reason for it be from there.
The noise usually starts around 45 MPH
I checked the heater fan and it appears to be Okay. I don't know of any other fans in that area.
View 12 Replies
Have a noise coming from the serpentine area. Sometimes it's a bit of a chirping, other times it's almost like a solid grind.
I pulled the belt off and the idler pulley had a bit of play so I replaced that. The tensioner pulley felt fine. I'm suspecting the fan clutch, as the noise only appears after the clutch has disengaged the fan (although it could be this is just masking the other noise because I've got a heavy duty / loud fan clutch setup).
How can I be sure that the fan clutch is the culprit before replacing it?
View 1 Replies
Got a 1999 ford f150 2 wheel drive. I have replaced both upper and lower control arms with ball joints on both sides. New shocks, new stablelizer links, new inner and outer tie rod ends. Also, a new steering gear and i still have popping noise coming from both sides around the wheel area when i enter or leave out of drive ways, turning, or running in a hole. Doesn't do in going straight. I don't know what else to do. Driving me insane. I keep spending money on this truck and still where i first started.
View 9 Replies
My 1997 4.0 Rear Wheel Drive is making a clicking noise when it is put into gear or when it switches from drive to reverse and vice versa. Sound is coming from the back of van. Does not make noise all the time. Drove 50 miles last night with no problems and minimal clicking. Could it be U-Joints going bad? Or is this a different problem?
View 6 Replies
So my 2010 with 20k miles on it just started to have some jingling/chirping noises around the drive belt area. It isn't all that loud but i can hear it. Could this be just a simple loose belt? Are our belts auto adjusting or manually adjusted? The noise increases with engine rpm in all gears and in neutral. Is def coming from the belt area.
One pulley does seem like it is not perfectly round and I can see some very slight run out from side to side. Nothing really obvious though - that might be normal?
View 13 Replies
I have a 97 250 LD 5.4 that suddenly has a grinding noise coming from the area where the transmission and motor meet. I took the inspection plate off the transmission and can look up inside there and see everything moving. I use a screw driver and if I flex the plate that mounts between the transmission and the motor I am able to get the noise to quiet down until I release the screwdriver and then the plate flexes back and scrapes making the noise again.
I can not see where the plate is grinding when I look up inside there. I can't figure out how to fix this.... Why it would just start doing this on its own as none of the bolts on the housing have been removed except for the two bolts that hold the starter on. (Changed it a couple of weeks ago). Thought about loosening the bolts on the tranny housing but I'm afraid that it would open me up to further problems???
View 4 Replies
I got a 97 f150 single cab short bed. My 4x4 shifter is on the floor and moves. I put in 4x4 and the relay clicks and the light comes on. Same as 4low. Front driveshaft spins but front wheels don't. Could there be a leak in the auto locking hubs? Also I want to manual convert the auto hubs. It can be done but how?
View 1 Replies
My front left rotor is warped and makes that annoying chirp chirp chirp sound as I'm driving. I hear it while the truck is driving and also when braking. I jacked up the front left tire under the control arm, removed the tire and caliper/pads, tightened the rotor against the hub with the lug nuts. Watching the bottom of the caliper mount as a reference point, I can clearly see the distance changing between the rotor and the mount as I rotate the rotor.
And I feel the resistance as the rotor gets closer in that spot. Is this simply a warped rotor? Or is something else causing this? I replaced the pads, rotors, front brake hoses, front left caliper and , still the chirp remains. The pins are greased and slide nicely. I also bled quite a bit of fluid out, since it was a bit dark compared to the new fluid. I checked for play in the tire, thinking maybe a bad wheel bearing, but found none. No other noises or symptoms in the front end.
View 3 Replies
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 Replies
I just installed the Donaldson B085011 filter last night. I understand the swoosh noise when shifting is normal. But, I noticed a chirpping when coasting. I first suspected suspension parts maybe but after reading on here could it be surge? I've seen some videos of what surge sounds like and it does sound like that but most people say it only happens under load and I'm hearing it just coasting down my farm market road to a stop sign without hauling anything. I'm researching billet compressor wheels now. Am I on the right trail to resolve this?
View 10 Replies
Bought truck new in 1997, 4 cylinder, 5 speed, manual transmission, 127K miles. In January developed a clanking noise in the engine area. Do not have a tach but hear the sound when engine is cold. Raise rpm up to whatever is equivalent to 20 mph in second gear. Anything much above or below this speed, sound goes away. Hear it the loudest when I am under the vehicle. Sounds like marbles in the exhaust system. My mechanic said it is not in the exhaust but in the front engine area. Said this vehicle is know to have this problem and there is no inexpensive fix. Sound goes away when engine runs for about 15 minutes.
View 2 Replies
2008 lexus es350 -- chirping noise from serpentine belt area. Chirping starts after a bit of driving. Got belt replaced, mechanic says it is water pump (as he says he saw marking and could be a prior leak), but I don't want to do this trial and error.
I got belt replaced by the mechanic who said wold fix the problem but did not. Should I replace water pump as it is expense on es350 and only to have chirping noise not fixed as it could be something else like alignment or idler pulley etc.
View 3 Replies
Got a 97 ford explorer sport that wont start. It will go like its going to start but I've only got it to run with ether then dies got new battery n tps thinking its the alternator because i hear a ticking in that area and the battery is now dead after i charged it all the way up granted. I did try consistently to get and keep running?
View 3 Replies
