I got a question, what is after ac hose vacuum left side on a 10 th gen 4.2l engine bay by the firewall, to the right of the blue thing, right of that on that line their is a 2 end diameter rubber vacuum line? What is that called, I need a replacement.
View 7 RepliesSo here's the background. I recently bought this truck. It's a 97 Ford f150 4x4 4.6l 99w vin code. Anyway Driving it home got a p0401. No problem. I Applied vacuum from other vacuum source to EGR engine stalls. So to me passages are clean in the throttle body. I checked to verify and indeed passages are clean. No while doing so I noticed no vacuum was making its way to the dose valve thing. Strange.... So took the line that runs to the passenger fender to dose off and it was impossible to blow air through.
So I cut out the clogged section found solder in the line. I filled the gap I now created using some 5/32 vacuum line reconnected to test and to my anvil still not vacuum. So I disconnected it again. Went directly to where the yellow/orange dose vacuum line connects to at the passenger fender and to my surprise no vacuum there either. No my question is. Am i suppose to have constant vacuum to the dpse or I'm I just being an idiot. And two if I am suppose to when the vacuum line runs into the passange fender where does it go from there and could I have a major issue in my hands?
I have a 1997 4.2 and when i got it the big vacuum reservoir under the passenger fender had the lines broke off. Where these lines go or have a diagram...
View 1 RepliesOk, I have 1997 Ford Ranger, 4cyl, manual transmission, and more miles than I'd like to admit to.
Yesterday, I noticed that one of the vacuum lines was coming dangerously close to hitting the serpentine belt on the front of the engine. The clamp that normally holds the vacuum line in place rusted away a decade ago, so I decided to use some velcro ties to attach the line to the positive battery cable. I didn't twist or pull on the cable in any way and the vacuum line isn't applying any force to the cable.
I get in the truck a few hours later, hit the key and I get >click<, but nothing out of the starter. One click when the key is in the start position, nothing more (as opposed to click-click-click).
Not thinking about my repair earlier, I went down to Autozone and had them test the battery - 12.8V and 550CCA, no problem there.
So then, I thought well since the click is coming from the starter relay, maybe that's where the problem is. I read on another forum that sometimes the starter relay can be resurrected temporarily by hitting it with a hammer. Which I did. And it did work! Now the truck is starting up normally every time, but I'd like to replace whatever was bad.
My questions :
1. Did I prove anything by hitting the starter relay with a hammer and then starting the truck?
2. Should I still be looking at the battery cables?
3. Should I stop hitting random parts with a hammer and take this truck down to a real mechanic before I do serious damage?
Time to replace the aging vacuum lines to the 4wd and probably anywhere I can find the old rubber stuff.
What is the size of the lines and are they mostly the same?
I'd like to order a roll so I can make ones like the front hubs longer, stuff like that.
Need to identify this part? I believe this part is causing my check engine light to continually come on, due to worn out connectors (I.e. Vacuum leak)!
View 8 RepliesI have a 1997 ford f 150 with a 4.2 ltr v6 the check engine light came on so i took it to autozone and had the code pulled. They told me that the o2 sensor bank2 sensor 1 which is before the converter had a slow response so i checked the wiring and bought the o2 sensor. They told me bank 2 is the passenger side but well i changed the1st sensor on the passenger side and reset the code and drove the truck about 130 miles . and the light came back on. After reading a few posts. I think they told me wrong is the drivers side bank 2 or is the passenger side bank 2 ...
View 14 RepliesMy 2001 F-150 4.6L was hesitating around 1500 RPM and the check engine light was on, dealer said the oxygen sensors needed to be cleaned. Had the work done and the problem still exists, the check engine light intermittently came on. I tried 89 octane fuel and the check engine light is off and the engine runs smoothly. I'm just a weekend mechanic and can do mostly basic stuff but the only time I've come across something like this is when I accidentally put 87 octane in my bike.
View 4 Replies99 F250 LD 4x4 w/5.4 - 218k .... Check engine light just came on so I had the trouble codes pulled. 071 and 074 . Lean on banks 1 and 2 . Truck is running fine as far as I can tell. I know it can be o2 sensors, pcv, maf sensor or loose vacuum line somewhere. I just put a new motorcraft pcv valve on before this happened so I rechecked the lines , all seem to be fine. Is there a inexpensive scanner that I can check the o2 sensors without just throwing money at new ones.
View 3 RepliesSo I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
Ive got a question for all you code readers out there. My dreaded check engine light has been on for about a month. I bought a code reader recently and checked it out. Two codes come up; PO401 and PO446. What these mean. My book says "Exhaust Gas Recirc. Flow Insufficient Detected" and " Evaporative Emission Control System Vent Control Circuit Malfunction". Which sensors, location on vehicle, etc..... this is a 97 5.4L Expedition.
View 9 RepliesMy girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 RepliesI own a 1998 ford f150 4.6l triton v8. I was leaving my house to go on a snowboarding trip about three weeks ago it was a rather warm wet day and all of the sudden my check engine light began to flash. I immediately pulled over and restarted my truck, once it was started again it was solid.
I turned around and started driving towards home. I get a small amount of feedback from my speakers and usually it's a smooth whizzing sound but as i accelerated the sound began to stutter rather than remain smooth. after about 5 minutes of driving this went away and the check engine light remained on.
so today I went out it's also a wet day and it's raining quite a lot. on my way into town everything seemed okay. then on my way home the check engine light began to flash again and the feedback from the speakers became choppy again.
I would also like to mention my battery light is on but it was on prior to the first time this happened. I'm just wondering if the belt could be loose or slipping due to the wet weather?
It has been since the 80's that I have attempted to do any work on a vehicle. How do I find a vacuum leak and where is my vacuum canister. I am assuming that it is a vacuum leak for anytime my engine has a load on it the air stops coming out of the dash vents and goes to the defrost vents. I have an 2000 F150 with the large engine with about 112,000 miles.
View 11 RepliesI recently had a Jasper rebuilt engine installed in my Ford E150. Since than my check engine light keeps coming on and the computer is saying my cas air mix is "lean". The instaler says i need a new fuel pump.Another mechanic says it is more likely a vacuum problem.I know it's possible that the fuel pump is bad bur since this has just started since the install, I don't believe it can be the fuel pump unless it's just one hell of a coincidence.
View 6 RepliesI have a problem nobody can figure out. My check engine light is on. Took it to Advance to have it scanned; came backwith Code 1226, Brake warning light ground short ( not concerned that at this time); Code P1285, cylinder head over temperature; and P1299, engine overheating (this repeated 4 times).
Now for the symptoms: Truck start and runs good, except with engine light on, runs about 4 miles, then the temperature gauge goes all way up, oil light come on (But oil pressure gauge is OK), Have loss power, and heater has no heat. I shut key off, restart, runs perfect, gauges OK, heater OK.
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesI have a 2000 f150 4x2 5.4 168k... Check engine came on,started shaking, weather was really cold. RPM would be a little high then low then back up. Especially when I turned on heater. Felt like truck would die but never does nor does it have issue starting.
So far, I have replaced two oxygen sensors inside engine,all coils, spark plugs, fuel filter, had injectors cleaned, intake cleaned. Truck runs better but, light came on a day later again. I can feel the tiniest of shaking going on and, cold mornings still make RPMS a little unstable. I was driving truck on highway at about 60 mph when a slight tug was felt and Truck check engine came on. I feel truck heavy, once it warms up completely, a little lighter.
Codes came up at auto zone as P1151
But I'm running out of options and frankly, money to fix this truck.
Checked the MAF and looked okay.
I'm with minimal skills.
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?