Ford F-150 - 1997-2003 :: Check Engine Light Has Been On - Codes PO401 And PO446 Came Up
Feb 15, 2004
Ive got a question for all you code readers out there. My dreaded check engine light has been on for about a month. I bought a code reader recently and checked it out. Two codes come up; PO401 and PO446. What these mean. My book says "Exhaust Gas Recirc. Flow Insufficient Detected" and " Evaporative Emission Control System Vent Control Circuit Malfunction". Which sensors, location on vehicle, etc..... this is a 97 5.4L Expedition.
View 9 Replies
Advertisement
1999 ranger 3.0. Check engine light popped up showing P1000 and P0401 codes. I think the p1000 is a system readiness test. Not sure why that came up and the 401 is exhaust gas problem. I put on a new autozone DPFE a few months ago..
View 5 Replies
I have a 2001 Chevrolet Prizm with check engine light showing PO420 and PO446 codes, what could be the problem?
View 1 Replies
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
View 6 Replies
I have engine light on and the code is PO446. just changed fuel filter on my 2006 5.4L f150. What the code means ?
View 1 Replies
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
View 2 Replies
PCV hose/grommet was rotted out with 1 inch hole but supposedly he spent a long time tracking down the problem. It was located way in the back middle (like underneath the wiper blades area).
2002 F150 XLT Crew Cab 4.6L 4x4 170K
What known issues would do this but not turn engine light on? Motor sounds excellent and runs excellent. Previously it was missing and engine code come up as random misfire, misfire cylinder #2 and #4. I replaced the coil packs on 2 and 4 and erased the code and there was a 1000% difference. Ran excellent (still does).
However, a week later I noticed a subtle shake in the motor, and at idle it would stay at 1...maybe slowly chirp just above 1, and then sputter a little down to 1/2 rpm. It will do this and stay running, but sometimes it will cut off.
What are the possible things that you think it could be considering no check engine codes? (Bad motor?)
View 4 Replies
I am the second owner of a 97 Cherokee 4.0 2wd. My overdrive works now and then. my check engine light is on. I had it scanned it throws 2 codes. p0700 and p0705. It has 147k and we already replaced the entire cooling system including flushing the engine and system thoroughly . Now it has been sitting for nearly 2yrs. just not sure what direction to go.
View 3 Replies
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
View 6 Replies
My wife and I recently bought a 2003 Pontiac Vibe, a Toyota Matrix with slightly different skin, and shortly after we got a check engine light. When I inspected the car before purchase I noticed that there was black soot in the exhaust pipe. The owner told me that he'd put a cat back exhaust but I suspected I'd probably be replacing the O2 sensors soon and we negotiated the price accordingly. So now it's a month later and I bought an OBD II checker. I followed the instructions and after the checker and the cars ECU linked it showed no stored codes. I turned off the CEL and we went shopping. Mid way on the drive home, we live out in the country, the CEL came on again. Went through the procedure again, still no codes stored. I've read the instruction manual twice and I don't think I'm doing anything wrong. Is it possible to have a check engine light on and there to be no codes stored for the OBD tester to find? I could have bought many rolls of black tape for what the tester cost and I kept the receipt just in case.
View 5 Replies
Need to identify this part? I believe this part is causing my check engine light to continually come on, due to worn out connectors (I.e. Vacuum leak)!
View 8 Replies
I have a 1997 ford f 150 with a 4.2 ltr v6 the check engine light came on so i took it to autozone and had the code pulled. They told me that the o2 sensor bank2 sensor 1 which is before the converter had a slow response so i checked the wiring and bought the o2 sensor. They told me bank 2 is the passenger side but well i changed the1st sensor on the passenger side and reset the code and drove the truck about 130 miles . and the light came back on. After reading a few posts. I think they told me wrong is the drivers side bank 2 or is the passenger side bank 2 ...
View 14 Replies
My 2001 F-150 4.6L was hesitating around 1500 RPM and the check engine light was on, dealer said the oxygen sensors needed to be cleaned. Had the work done and the problem still exists, the check engine light intermittently came on. I tried 89 octane fuel and the check engine light is off and the engine runs smoothly. I'm just a weekend mechanic and can do mostly basic stuff but the only time I've come across something like this is when I accidentally put 87 octane in my bike.
View 4 Replies
99 F250 LD 4x4 w/5.4 - 218k .... Check engine light just came on so I had the trouble codes pulled. 071 and 074 . Lean on banks 1 and 2 . Truck is running fine as far as I can tell. I know it can be o2 sensors, pcv, maf sensor or loose vacuum line somewhere. I just put a new motorcraft pcv valve on before this happened so I rechecked the lines , all seem to be fine. Is there a inexpensive scanner that I can check the o2 sensors without just throwing money at new ones.
View 3 Replies
I got a question, what is after ac hose vacuum left side on a 10 th gen 4.2l engine bay by the firewall, to the right of the blue thing, right of that on that line their is a 2 end diameter rubber vacuum line? What is that called, I need a replacement.
View 7 Replies
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
View 9 Replies
I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.
View 14 Replies
I own a 1998 ford f150 4.6l triton v8. I was leaving my house to go on a snowboarding trip about three weeks ago it was a rather warm wet day and all of the sudden my check engine light began to flash. I immediately pulled over and restarted my truck, once it was started again it was solid.
I turned around and started driving towards home. I get a small amount of feedback from my speakers and usually it's a smooth whizzing sound but as i accelerated the sound began to stutter rather than remain smooth. after about 5 minutes of driving this went away and the check engine light remained on.
so today I went out it's also a wet day and it's raining quite a lot. on my way into town everything seemed okay. then on my way home the check engine light began to flash again and the feedback from the speakers became choppy again.
I would also like to mention my battery light is on but it was on prior to the first time this happened. I'm just wondering if the belt could be loose or slipping due to the wet weather?
View 2 Replies
I have a problem nobody can figure out. My check engine light is on. Took it to Advance to have it scanned; came backwith Code 1226, Brake warning light ground short ( not concerned that at this time); Code P1285, cylinder head over temperature; and P1299, engine overheating (this repeated 4 times).
Now for the symptoms: Truck start and runs good, except with engine light on, runs about 4 miles, then the temperature gauge goes all way up, oil light come on (But oil pressure gauge is OK), Have loss power, and heater has no heat. I shut key off, restart, runs perfect, gauges OK, heater OK.
View 5 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
I have a 2000 f150 4x2 5.4 168k... Check engine came on,started shaking, weather was really cold. RPM would be a little high then low then back up. Especially when I turned on heater. Felt like truck would die but never does nor does it have issue starting.
So far, I have replaced two oxygen sensors inside engine,all coils, spark plugs, fuel filter, had injectors cleaned, intake cleaned. Truck runs better but, light came on a day later again. I can feel the tiniest of shaking going on and, cold mornings still make RPMS a little unstable. I was driving truck on highway at about 60 mph when a slight tug was felt and Truck check engine came on. I feel truck heavy, once it warms up completely, a little lighter.
Codes came up at auto zone as P1151
But I'm running out of options and frankly, money to fix this truck.
Checked the MAF and looked okay.
I'm with minimal skills.
View 13 Replies
