I am changing the passenfer side exhaust manifold on my '00 150. The bolts all came out fairly easy, sprayed them often in PB over the last 2 days, my problem is the 2nd and 3rd nuts on the bottom are under the motor mount. Do I need to remove that or is there an easier way that I'm missing.
View 11 RepliesTruck Specs: 1997 F250 LD 184000 miles and a 5.4, automatic, shift on the fly 4x4 extended cab.
What I did: Changed the exhaust manifold gasket on the right side. There were some broken studs which came out with a stud remover.. No torch was used during this evolution.
What happened: After driving 10-15 miles it set the codes that I listed in the subject line. Reset the codes 20 or so miles later the P1131 code set again. (both times there was a noticeable loss of engine power) The upper O2 sensor checked out with a meter. When I checked the voltage on the truck's harness plug referenced to the NEG terminal on the battery, both the power and gnd had 12V- Key On Engine Not Running (KOENR).
What I did: Cleaned the connections put dielectric grease in the connections and reassembled. Reset codes; all was well ~ 100 Miles later the codes are back. I also ran a continuity check from the plug to the control module, they check out fine.
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesSo I think I have possible manifold leak in my exhaust and its because when the engine is super cold, and I do have a straight pipe, but it sounds like a tractor... until it warms up after few minutes, it goes away.
My exhaust manifolds are rusted to crap and stuff is falling off, paint or whatever there was on them.
Now I've looked at bunch of videos on UT to get a better understanding since everyone says the nuts and studs are hard to remove or snap.
Now my question to anyone who's done this in their garage; I've seen bunch of videos where the stud snaps flush, then he takes a nut, puts it over the hole, holds it up with needle pliers and uses a MIG to start welding it... stud to nut... then puts a wrench and off it goes.
Now, I'm not a pro welder or anything so is it possible to by accident weld the stud, nut into the head and then never ever be able to undo or take either one out?? or is the head or whatever made from different material that won't get welded to the nut or the stud??
I have a 98 F150 4x4 Super Cab 4.6 auto that has a leaking exhaust manifold. I changed both manifolds about 3 years ago and the passenger side bank is leaking again. I haven't gotten into yet to see if its just the gasket or the manifold itself. My question is does anyone know of a set of headers I can put on the truck that will bolt up to the existing exhaust? If I make the switch to headers I don't want to have to redo the whole exhaust system.
View 3 RepliesI have a 1999 ford f150 4.6 engine and it has an exhaust leak but wondering what is the procedure to remove a broken bolt and the rest of the bolts on the manifold
View 2 Replies2003 F150 5.4 4x4 supercrew ,76k miles
Recently the passenger side exhaust manifold cracked on my truck. I bought this truck about two years ago with 58k on it and currently have 76k miles. I remember getting the carfax report and being relieved to see that it had exhaust manifold replaced in July of 2014 at 49K miles along with a new EGR tube. I called the shop that worked on the truck to see if he could confirm that both manifolds were replaced since carfax only said manifold & egr tube. The shop manager confirmed that both manifolds were replaced and he told me that they were most likely manifolds from napa according to the part number.
Now, my question is, what's the best brand to replace the manifolds with? Should I just go with OEM and spend the extra $130 per side? I know the manifolds are a common problem with these trucks but only lasting three years and 27K miles just seems ridiculous to me.
I'm hoping that when I get around to actually doing this that they wont be to bad because of how recently they were replaced. For now I just cleaned the area with a wire wheel and used the inferno metal repair. Seems to have done the job but I don't expect it to last long, just another month or two until I move to a place where I can actually work on my vehicles.
I was looking at my exhaust manifold..and I found a couple of studs missing...so if I want to replace both of them , is it better if I replace all of them on both sides of the engine ?
By the way..my exhaust manifold is good I don't think none of the studs are broken.. but I have been having this engine knocking noise on my engine, do yall think a couple of studs could be the problem of why my engine is knocking?
If the exhaust manifold gasket is broke / cracked will it making a ticking sound?
View 5 Replies I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
How difficult is it to change the passenger exhaust manifold? I have just finished replacing the left exhaust manifold. The biggest issue was rusted fasteners and inexperience. Have torches. Any you tube videos show the left manifold being changed but not the right. I do not have a hoist and work in my driveway. Is the right side more difficult and should I leave it to someone with a hoist?
View 4 RepliesI have a 2000 with a 5.4 and 166K miles. It had multiple exhaust manifold studs broken on both sides. Now that thay is fixed, I am getting the p1131 and p1151 codes. The EGR tube was also replaced at the time of the manifold fix. I checked over all the tubes and electrical connectors to rule out something simple but did not find anything out of place. The intake manifold was replaced with a new Napa one less than 5K miles ago as well.
Could the leaky exhaust manifolds over time set the fuel trim level high and now that they are fixed, the ECM is thinking it is running too rich? Can the ECM be reset to zero? There is also a ticking/rattling noise when you accelerate that seems to be coming from the fuel injectors. I listened with the stethescope and they are the only things that sound like the noise I hear. Could these all be related?
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesSo I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 RepliesAbout to do the exhaust manifold gaskets on my 03 f250.
View 3 RepliesI managed to get the drivers side exhaust manifold and all of its bolts off no problem. On the passenger side I had 1 bolt head that was already broken and I have only 1 other that is still holding on for dear life. I've been soaking it in aerokroil for awhile now and no luck. I tried some PB blaster today because I am willing to try anything. I also tried heating up the bolt with a torch and some map gas but not sure if I am heating it up enough or not. Anyways, everything else has been going great, got the uppipes off and the valley, turbo and pedestal all cleaned up good. Just need to get the last whole bolt and broken bolt out so I can install the new manifolds. What I should try to remove the last 2 bolts. How hot should I get the bolt when trying to remove it? Or should I be heating the engine block?
View 12 RepliesWell i had an exhaust leak on this F250 and so I started torquing the bolts on the manifold to the head. (45 ft.lbs) A couple were very loose so I was thinking "Great, this may fix my problem!"
My first mistake was probably the Harbor Freight Tools torque wrench.
I am on the driver side, second from the rear and then bang! I see a gaping hole where the bolt used to be. Bolt on the floor. I cant see up in the hole to the head, I think it broke flush with the head.
2003 F350 short bed 6.8L V10---On start up a slight tap sound, almost like a cranky lifter, but it is an exhaust manifold leak. At the bolts, I am not sure. This has been this way for 5 years, no better no worse. After I run about 2 to 3 minutes it seals itself. Not a hint of noise. Due to heat, something is expanding to seal it (aluminum).
At my annual PA. State Safety Inspection the Tech says 'that has to be corrected if it worsens', but It does not fail inspection. This puzzles me.
How is the call made for correction. A flip of the coin, a guess and is it serious enough to fail inspection. Is this normal with the 6.8L or V10s. I know the cost involved for a fix is big league, but can it be justified. TRUCK RUNS GREAT !---
I have an 03 F250, 5.4, 4x4, with aprox. 130k miles. I recently had my exhaust manifolds replaced because 1 literally cracked in half. Ever since the replacement, I'm getting worse gas mileage! Im only getting aprox. 250 miles to a tank when before it was well over 325 (highway)...
View 1 RepliesI have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 Replies