Ford F-150 - 1997-2003 :: CEL On With Two Codes - P0705 And P0171?
Mar 6, 2013
Ok, so this past week i towed my 72 f250 to IL from CA. 2100 Miles. 6100#s with the trailer. No problems at all. Got about 9 MPG too the whole way. Ok, so here is my problem now. As some of you may know, IL just got about a foot of snow. Its all slush at this point. I am living in the country right now so i drive thru alot of it. Ok, now you know the back story, today i drove the truck to my brothers house, put it in park and bam! check engine light came on. About a half hour later i drove it to AutoZone and had them check the codes. Here is what they pulled.
P0705
P0171
Need to know what to replace. I have to drive it back to CA in 4 days.
View 1 Replies
Advertisement
So I have a 1997 ford f150 v8 4.6 2w... I got codes p0171 and 174 my truck seems fine till the idle drops, it's weird when I have it on park it's fine if I turn the wheel left the idle drops when the ac turns on the idle drops and it's wasting crazy gas. Where should I start first in finding this problem?
View 12 Replies
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
View 6 Replies
2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?
View 10 Replies
So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:
P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?
Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.
Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?
View 7 Replies
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
View 2 Replies
I have a 1998 F150 5.4L 4WD with 192k mi on it. Recently ( suddenly ) the vehicle began shuttering pretty alerting under light load at 35 - 45mph. The engine idle was intermittently smooth then rough. I quickly drove the truck home and ran a Trouble Code check with my Autoxray EZ-scan 4000 and found the two trouble codes P0302 and P0171. I have checked for vacuum hose cracks and found none.
Replaced the fuel filter, PCV valve, and cleaned the MAF sensor ( dirty ).
Right after cleaning the MAF sensor the idle remained smooth - but stumbling immediately when put in drive. Driving at 35-45mph still exhibits intermittent shuttering and occasional very short bursts of what feel like complete engine shut-down. This all is evident under light to moderate load .
At this point what would you recommend ? Replacing the O2 sensor bank #1 ? Or is there a possibility maybe the EGR valve is faulty - or another vacuum valve somewhere ? Intake manifold leak ?
The severe stumbling and very short complete engine shut downs would indicate that maybe the computer is failing or it's a fuel delivery issue? What rational steps to take next ?
View 14 Replies
I am the second owner of a 97 Cherokee 4.0 2wd. My overdrive works now and then. my check engine light is on. I had it scanned it throws 2 codes. p0700 and p0705. It has 147k and we already replaced the entire cooling system including flushing the engine and system thoroughly . Now it has been sitting for nearly 2yrs. just not sure what direction to go.
View 3 Replies
To start I was driving to work tonight and noticed the o/d "off" light flashing. it shifted hard one time then felt normal the rest of the way to work. At red lights the o/d light world turn off and about 3 minutes later it would flash again. When I got to work, I checked my code reader which gave me the p0705. I have searched around the net for about an hour and one thing i am seeing is that the fluid is "hot" or that there isn't enough. i have checked it and it looks slightly low like right above the add indication.
The only sound I here from under the truck is a rattle when in drive and at idle, but once I give it some gas it goes away. On they way home that night the o/d light was still flashing but it drove fine just at higher rpm, it down shifted hard one time but there were no other issues. I checked the fuses and they are all good.
View 8 Replies
I have replaced the transmission Range sensor (with OEM) and it is adjusted correctly, however This did not clear the. Code P0705... I am stuck ....
View 1 Replies
2003 Sport Trac. My car was not starting, told my fuel pump, replaced twice and nothing. Found out about inertia switch and changed it, now car runs.
Before this switch blew out my car was running perfectly, no check engine, nothing. Now i have changed my fuel pump twice and put a brand new fuel filter in and soon after i get lean codes P0171 and P0174. My fuel pressure is 60psi at idle and drops to 0 after about 30 seconds when the car is shut off.
A lot of my intake is new since i did have a vacuum leak before, so i do not suspect that is it, especially since this happened after the new fuel pump. I am completely stuck as to what i should do. And i get hesitation when trying to accelerate sometimes
View 3 Replies
2003 Ford Explorer, with P0171 and P0174 codes, common problem, as I have read. I pulled the cover over the engine off, and I immediately found the likely problem. There is a hose/connection that runs from the valve cover on the right side, about 6 inches behind the oil fill tube across and looks like it comes into the Carb. Where it turns to come into the carb is a rubber elbow. This elbow has a hole in it. Temporarily I have used electrical tape, but when I run the vehicle, I see the elbow begin to collapse. I believe the elbow is getting weak with age, plus the hole/tear doesn't work. Anyway, what i the part number, or what this is called. Hoping Advance Auto, or Napa will have it, just don't know what it is called, and can't figure out the part number. Otherwise I will pull it off tomorrow and take to advance and see if they can match it.
View 5 Replies
I have a 2003 F150 4.2 with 155000 miles. What may be causing this?
View 6 Replies
I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
View 14 Replies
The "service engine soon" light on my 2003 F150 Supercrew 4.6L (225k miles) just came on. The code it's throwing is P0171.
View 3 Replies
1999 xlt with 5.4 lt p0171 only. it started with what felt like a misfire or hesitation and rough idle. Extremely rough at 40-45 mph. but with no misfire codes just p0171 so all 8 coils and plugs and sparks replaced twice in one month. and still same code tested fuel pump pressure 28 psi.... removed clogged cats, still same code... new pcv valve and elbow.... checked for air leaks around intake and intake manifold and nothing.... cleaned mass air flow sensor...I can unplug any coil on bank 1 and it wont make a difference. But if I unplug any bank 2 coils and engine makes a difference.
View 2 Replies
I am still battling a p0171 code on my 2000 f150 5.4. I checked the fuel pressure at idle it sits at 31. I remove the vacuum line off the regulator it goes to 41. When i give it throttle when in gear it will maintain at 30. And when I shut the vehicle off completely it will maintain 38. Just looking to see if this is correct numbers. I was trying to determine a weak fuel pump.
View 9 Replies
97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
View 4 Replies
2002 7.3 4R100 ... The truck started flashing the O/D light pulling a 9K lb trailer on the highway.
The transmission codes read were P0705 (Range Selector) and P0873 (bad 3-4 shift - RPMs did not drop).
On the highway, the TCC seemed to lock up fine in 4th (OD button was set to leave O/D ON). When the truck would downshift (not often) then it would sometimes would rev high when it downshifted. It was like 3rd was slipping or it was downshifting into 2nd instead of 3rd. I think it was doing a 4-2 downshift but not 100% sure.
What confuses me is that if it is doing a 4-2 downshift then it would have to change state of both valve body solenoids. Is it possible that it was doing a 4-3 shift but solenoid was sort of sticking? Trans fluid looks fine.
I have read other posts where people had same problem (titled 3rd gear slipping), but they never seemed to resolve the problem in the thread. How likely is it that the solenoid is the problem? It seems to drive fine in 3rd when the O/D OFF button is pressed and O/D is not allowed.
View 6 Replies
97 F150 4.6 Vin 6, 5-Speed Trans, 200,000mi, Rebuilt recently. I was on my way to get my truck smogged, but she threw a code, P0171. I read somewhere to clean the throttle body elbow, which I did (needed to do it anyway). After I had everything put back together, I start her, and it's rough and immediately dies. If I keep the RPM's at about 1.5k for a minute, then let off, the truck will run fine for about 30-45 seconds, then die again. I just replaced my IAC and the problem persists.
View 8 Replies
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
View 2 Replies
