...Is there anything special that needs to be done for brake bleeding after putting in a new master cylinder? I decided today to flush my system with my vacuum bleeder and now my pedal slowly falls to the floor at a light...No problems in a panic stop or otherwise, just falls to the floor slowly when braking...no leaks, so I'm assuming a master cylinder is an order....
View 14 Repliesll, I changed out the master cylinder on my 2002 F-150, disk brakes front and back w/ ABS. Bleed all the air out and bench bleed the master cylinder. I have good pedal but the brake light will not go out.
View 6 RepliesWhat kind of brake line is it and if is replicable with regular brake line? I'm just replacing long line between front and back splitter block and just would like to know what is it. What is purpose of that braiding (?) at front brake lines and why they wind down instead of going straight. Part of that long line is braided too, part that go across frame.
View 3 RepliesI have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 RepliesI'm having trouble bleeding the air out of my slave cylinder or master cylinder in my clutch system. I've been trying for a couple days now is there a trick to this?
View 7 RepliesThe cruise switch on my brake master cylinder is bad and causing the cruise to not work. I have it bypassed with a jumper wire and it works fine. is there any reason not to do this?
View 11 RepliesI've got a 1997 f150, 4.6. It sat for year and a half, trans went out and it wasn't my primary vehicle so wasn't to worried about fixing it. Until now, well got a new trans put in it, fired it up. And had a misfire, #3 and #8. Changed plugs and wires, same thing. Getting spark at the plug. So I changed both injectors, still nothing! I'm kind of stumped now.
View 4 RepliesI tried to replace my brake master cylinder today but wasn't able to because of a plug
It's the black plug on the drivers side, the connector is upside down so I can't see how to unplug it I tried for an hour then got too frustrated I had to come inside
My Haynes manual says "unplug" obviously
Just purchased a 2003 GX470 with 160k and after the low brake fluid light came on I noticed the master cylinder had a leak. After removing the cover it appears the fluid has leaked for quite some time as the paint has started pealing from the frame. The brakes however appear to be working correctly. Upon purchase the front calipers were seized and I replaced both front calipers.
After having someone depress the brake pedal while I watched, the fluid leaks from the end of the master cylinder each time pedal is pressed in.
After doing some research it appears there is a rebuild kit for the master cylinder.
I recently noticed that my brake fluid was leaking in my 2003 Hyundai Elantra and upon further inspection I found the leak was coming from a part near the master cylinder. I looked online and couldn't figure out if this part was part of the master cylinder or brake line or a part all on its own. I tried tightening it but It still leaks some. I read a similar post online and that it could just be that the washer needs replaced but I just wanted to check on here to see what the part is called and if I should just replace the whole thing. I included photos as well.
View 7 RepliesI replaced my MC cap and gasket less than a year ago with a Dorman replacement and I'm leaking again, already. I don't want this to be an annual thing! Any good quality replacement? Is there any tip or trick to get the gasket to seal better?
View 9 RepliesEarly 70's Ford truck. The brake MC fluid is filled but not overfilled, and doesn't leak at all when the truck is parked. It can sit there for a month and never leak a drop, parked. But when I drive the truck, even just around the block, then park, and look inside the engine compartment immediately the brake MC is dripping brake fluid. It appears the leaking mode is by the fluid somehow jumping up and coming over the top edge of the MC when the truck is in motion or when the brakes are applied. All my diy'er years of replacing brake master cylinders on Ford Galaxies, VW Rabbits, Corollas, and this truck, I've never seen this kind of weird brake problem before. On this MC design it seems there's sort of a rubber baffle inside the lid of the MC, and that's present and accounted for.
View 17 RepliesWhy the brake lines have 2 or 3 coils in them near the master cylinder? Makes it a real pain to work on anything down in that area. Always snags ratchets and stuff...
My brother and I were discussing it the other nite, and the conclusion we came up with was, the first guy ever who was installing a brake system had tubing that was a couple feet too long, and couldn't find a tubing cutter, so he coiled them up.
Then the next guy saw that and figured "hmm, so THAT'S how it's done", and so on... Kinda like the story about the lady who always cut off both ends of her ham before she put it in the broiler..
My son's 2006 F-150 4x4, with 107,000 miles, has in intermittent brake light on. I replaced the rear pads, as they were nearly into the rotors. The brake pedal feels fine in all braking conditions. Could the master cylinder still be going bad? Anything else to check?
View 4 RepliesI have a 79 f150. I changed two brake lines and master cylinder and bleed,and more bleed,but still very soft all most to floor? wheel cylinders look good.
View 2 Replies1987 F-350 460 Auto Trans. Brake Pedal slowly going to the floor. Stopped at a red light yesterday on a slight down hill and I noticed the brake pedal slowly going to the floor. I had to put the truck in Park to avoid bumping into the car in front of me. I checked brake fluid level and still at the full level, check rims for brake fluid leak from brake cylinder, none. Could my master cyclinder need rebuilding or is my vacume diaphragm going. Not sure thats what its called.
View 14 RepliesI have replaced the cruise control cut off switch and post-recall pig tail twice in two years for fluid leaks. Whats the deal do they all leak?
View 6 RepliesI replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 RepliesStopped after a hard pull and noticed I had coolant dripping off the front sensor on the Brake Master cylinder. Coolant level was down in the Degas bottle. Searched everywhere for the source of the leak, and couldn't see anything. Today the drip had stopped, but when I squeezed the rear heater return hose under the Degas bottle it appeared to have a wet spot form.
I'm thinking I have a very tiny pin hole, and plan on pressurizing the system to see if I can determine for sure this is where it is. Before I do though, where this high pressure leak might be coming from? Degas bottle and cap is less than a year old. Doesn't appear to be any signs of leaks around the clamps. That rear heater hose.
A few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
I have power steering fluid leaking out of the bottom of the Brake master cylinder out of a round hole. Every time I pushed brakes it leaks a good amount of power steering fluid out. Why it would do this and is there a screw missing out of the hole or what?
View 6 Replies