Ford F-150 - 1997-2003 :: Big Cloud Of White Smoke Came Out When Going About 55 MPH And At 2800 RPMs
Dec 26, 2013
The truck is a 98 4.6l with 188,000 miles on it and yesterday i was driving up over a pretty steep grade hill, i was going about 55 and turning maybe 2800 rpms at the top a big cloud of white smoke came out (either tailpipe or just out of motor on hot pipes)and also some in the cab. It didn't run any different though so I kept driving about 3 mile and stopped where i could take a look and and saw fresh oil around the starter area running down where the motor meets the tranny. I checked the oil and it was at a good level and also not milky. I checked level again today and it seems well and there is no drops of oil on the ground i ran it home about ten mi and it runs good. What could have happened?
View 2 Replies
Advertisement
99 1500 2wd 5.7 burb
Out of the blue I started old red up yesterday (after charging the dead battery) and got a huge cloud of white smoke. Smells of coolant so Im thinking oh great a head gasket. The thing is, I can see no trace of coolant in oil or vice versa. I started it up with radiator cap off, while cranking I got a little fluid spit out the neck but once it started it was not gushing or bubbling at all.
View 1 Replies
Last time I took my car for service at 26K miles, I picked it up asked if all is well. "Yes all is well", and I am glad I can continue my weekend. I get in it, drive it out and upon reaching 40mph a clunking noise comes from the front tire. I mean to bring it back but eventually the noise is less. I assume something was wrong. Before I know it, it is 31K miles and i need to bring it back to service. I mention the front left tire. Turns out all 4 tires are cupped. They recomend changing the tires. I what to see if i can afford it and to see the tires myself. There is some shape alteration.
I take it easy because i think...if the tires are not great, i should be careful. Both the husband and I go to a shop, drink coffee, I think i can change the tires in a few days. On my way home, as I am trying to merge into traffic and get up to speed one huge puff of white smoke comes out, lights pop up (OBD blinking and solid slip light). My husband was right behind me with his Tundra. We are only a couple of miles away from the dealership and decide to bring it back...slowly nothing above 30mph. Service dept is closed and I have left it overnight.
Both of us agree...this should not be happening...specially when I have always serviced it regularly at the dealership and have always requested the recommended service.
View 5 Replies
I have a 2002 Toyota Highlander 6 cyl, 148,000 miles. I get a cloud of white smoke from the tailpipe upon starting a cold engine. Smokes for about 1-2 minutes, then smoke stops.
View 4 Replies
My dodge spirit has 80,000 miles on it. i love this little car, however, yesterday for some reason while driving my radiator reservoir started to overflow. I didn't notice at the time, but when i got home there was water in the engine compartment and it was obvious that it had come from the reservoir. This morning I went out to drive the car and at first the engine shook a little but then started running smoothly, when I backed out i noticed a rather large cloud of white smoke (water in the engine) I immediately turned off the car. I have a feeling I will need to rebuild this car's engine. What I should expect to pay for this repair?
View 6 Replies
Fine one day, no start the next. Been skimming over the 7.3 no start thread, so w got some ammo for him to check. White smoke while cranking, rpms move while cranking. Nothing to read codes or other sensors YET. Tried the unplug ICP and it "wanted" to fire. So, I have him my spare IPR to try. I'm sure he checked the fuses but will confirm via text...
View 9 Replies
I just bought a 97 f150 4x4 4.6L v-8 and keep having problems. The check engine light came on saying that it is running too lean. The truck had been sitting for a while so I changed the air filter, maf, and pcv valve. After changing the pcv valve it is now blowing white smoke. What can be causing this to happen?
View 1 Replies
I have an 01 f-150 4.6 triton and it now blows a sometimes pretty big ploom of white smoke at start up. Sometimes it smokes for a while after that and sometimes not. It runs smooth and strong but I have no clue what to do...
View 13 Replies
I have a '98 Expedition with 170k, 4WD, 5.4 and auto trans.
I drove me truck home about 15 miles and sat idled for 15 minutes while on the phone. The truck started running rough all of a sudden and then died. I tried to restart it and would crank over, but not ignite. I thought fuel pump, grabbed a can of starting fluid and eventually fired up, but was huffing white smoke. After about 3 minutes, it sat there and purred. No problem, right?....
I dropped it in reverse to back into the driveway, when I put it in drive.....nothing, no forward gears now..? It will start up and run now, but still no forward gears. I have a leaky heater core, but rarely have to add water......and no milkshake in the oil.
View 1 Replies
98 5.4L v8 and the obo stopped @359999 after i bought it and put a new engine in her, but my truck is blowing white smoke out of the vents. i have been told could be the heater core, radiator line ... not sure.can anyone help me with this?
View 5 Replies
2002 F350 7.3PSD, lariat 4x4 dually , 212k miles, automatic, crewcab, bone stock other than k&n filter in factory air box.
Bought the truck from used dealer with 168k miles on odometer. Drove it for two months and the radiator started filling with diesel. Had injector cups replaced. Had new o-rings on injectors and valve cover harness (both sides) at this time. While in shop they wanted to put injectors in truck but limited funds haulted that. Got the truck back and drove it for a while and noticed that when starting the truck it had a miss till it warmed up, but went away. This has been going on for over a year, but now has gotten much worse. Over the past year it has gone from slight miss to a full on dead cylinder that you have to make the truck pick up as you drive it. If you leave it sitting for more than roughly 10-12 hours you have to plug it up or it has trouble starting.
The final push from this ole girl was the other day. Left for work, normal hiccups and such from the truck. I pull up to a stop light and notice the truck is not sounding like its running correctly. No biggie it will smooth out, or so i think. I head towards work and the farther i get from home the worse it runs...
It wont pull its own weight, barely creeping at times. So i stop and check all my normals(oil mainly... just replaced hpop fittings and o-rings) and add fuel to it to get it over half tank. Start truck, still missing. Pull out on highway and dump foot to floor. It takes off only to fall on its face and start blowing white smoke out exhaust and die. It starts back but apparently I pissed it off cause from there it only got worse!!! It done that all the way to work, one time being so bad i had to stop and let traffic go by as the smoke cleared the roadway.
I get to work and check oil and it was way low. I add oil and drive it to lunch and it runs good, no hiccups misses or anything. Yay, problem solved!!! WRONG!!! Head home after sitting for a few hours and i pull out the parking lot and it falls flat of its face and goes into its dieing and such again. I limped it home and its sat in the yard ever since. Tried to start it today and after being plugged in for a couple hours it only sputters on a couple cylinders till it slowly dies. All Ive got for my troubles today has been two dead batteries...
This truck has always been underpowered as well. And gotten terrible fuel mileage (8-10 avg)... But it sure is pretty!
View 2 Replies
For over a year, the truck took 5-6 seconds of cranking to start, but always started. This morning it started, but shakes, coughs, and vibrates like hell. It revs up but still sounds like its hitting only on a few. replaced ciols many times over the years, but this sounds different.
View 6 Replies
I have a 2003 F150 with a 4.6. Exhaust is pouring out white smoke with a sweet smell. I have replaced upper and lower intake gaskets. Compression test on all cylinders are at 145. Confused and don't know where to go from here.
View 1 Replies
I'm losing coolant have, excessive white smoke coming from the exhaust, and rough idle. Doesn't over heat or even try to overheat. The oil fill cap looks brownish white. It drives fine other than extremely rough idle. I know how to check a blown head gasket with the combustion gas test.
From what I've read blown head gaskets on 4.6 fords are fairly uncommon but a blown intake gasket is fairly common. How can I tell the difference?
View 13 Replies
I have a 98 expedition with the 4.6l 4x4 and it has 158,000 on the dash had a new engine installed at 100,000 it started running rough and sluggish last week so I changed out the spark plugs and while changing the plug I notice oil on the threads of the two rear passenger side plugs. After the new plugs it was smoking pretty bad blueish white smoke. I figured it was the oil from around the threads that had leaked into the cyl.
The smoked cleared after 2 days and ran great for a week. Now its doing the same thing again real rough idle and and its extremely sluggish. I can put the pedal to the floor and she barely wants to move almost like the tranny is going out but the rough idle leads me to believe its and engine problem. I have the check engine light on but can't get any codes. I also tried checking for vacuum leaks by spraying either round the intake and vacuum lines and didn't notice any change in rpms so I'm guess the vacuum is fine.
View 7 Replies
My DD just developed a head gasket leak. I've been noticing a coolant smell for a few days and today saw lots of white smoke from the tail pipe. I figured this is where my coolant was going and sure enough there is coolant coming from the driver's side head. I've ordered the gaskets and new bolts, but need the install.
I think mostly what I will need is the intake and head bolt torque and sequence. I will need to take a few days off work to get it done. Truck is a 2002 F150 with a 5.4L engine.
View 2 Replies
'92 3.8l Trans Sport owner, 165 miles on it (if I can trust the previous owner), have this vehicle for 4 years now(I owned 2.3l version before - not to recommend).
At cold start, it starts without any problem, maintains the RPMs as it should and doesn't produce any white smoke. But when I start it when it's warm(or hot, doesn't matter), the car in a lot of cases won't be able to maintain the RPMs and die. If I apply some throttle for first 2 seconds, it will be ok and it will continue to run normally without any pedal assistance. From time to time this causes a very rough start and it will miss on 1 cylinder until it warms up a bit(15 second - 3 minutes). Regardless the way of starting(assisted or normal) it will start to produce a white smoke, when I wait at stop light for 30 seconds or more and idle becomes very rough and slowly starts to miss on one cylinder.
When I continue to drive, it's ok after a few seconds, until I idle again. My mechanic told me, it's the head gasket, but as nobody in the whole world does not complain about head gasket failure on 3.8l GM engine, I'm a bit sceptical and wouldn't want to invest money on something the car does not need. People mention the intake manifold failure is common for this engine, could that be the case? Car slowly loses the coolant(1l in 2 weeks), no leaks, water pump has just been replaced, smoke was present before replacement. Ignition is OK, new spark plugs, 1 year old cables, 2 years old ICM, first coils, sparks on all cylinders.
View 13 Replies
I just bought a 1991 F150 with a 302 (5.0). It idles at around 2600-2800 RPMs. The previous owners replaced the TPS and IAC, but it still idles fast. Ford dealership told them it was a vacuum leak. Are all the vacuum lines close to each other? How easy is it to locate/fix the problem?
View 2 Replies
I have a 97 Ford Ranger / 2.3L / 4 cylinder (L4) / 5 speed manual / XL Supercab / 140k miles. I had been having some Check Engine issues and ran rough in town stop light to stop light. But was fine on the highway.
On several visits to the parts store, their OBD tester showed:
PO303 (Cyl 3 misfire detected)
PO141 Bank 1 Sensor 2 O2 Sensor (heater circuit malfunction)
PO171 Bank 1 Combustion Too Lean (the most recent new code to show up)
And the following would show up sometimes, but other times not:
PO 402 EGR Flow - Excessive Detected
P1409 EVR (I cant remember the exact error message for this)
Regards the PO141 code, O'Reilly's sold me a Bosch O2 Sensor (Bosch 15719) and the sales rep told me it was the sensor closer to the engine. And with the attached cable length on the sensor showed was indeed the sensor closest to the engine. But I've been advised the Sensor 2 is for the 'downstream' sensor, furthest away from the engine. And the other sensor, that I replaced is the upstream sensor. And the error continued.
Then back issues showed up and I had back surgery this past year and thus drove the vehicle sparingly. Never resolving the check engine issues. (My bad). Ran on the highway ran fairly well. But recently noticed longer acceleration times and unable to top 65 in 5th gear. I bought spark plugs and plug wires and had plans to change next week.
Yesterday as driving down the Interstate, was 90 miles into my trip, I noticed loss of power even in fourth gear. (note it was the hottest day of the year at 100F). It seemed I used more gas than usual for that distance. I stopped for gas on the Interstate and power seemed to improve. Then about 130 miles into my trip I hit some heavy stop and go traffic, and wasn't able to keep an idle and the engine died numerous times if/when I didn't give it gas at a dead stop. The heavy stop and go heavy traffic and the issues persisted for a half hour for more than five miles. Then when traffic opened up the truck seemed to have a bit more power in 4th gear again. And up to that time all my dash gauges were showing fine. Then a couple miles or so down the interstate, driving 65mph in the inside lane, the check engine light started flashing quickly. And at the same time a sudden loss of power, rough sounding engine with heavy white smoke coming under the hood. And looked back in rear view mirror, with nothing but heavy white smoke. Managed to cross three lanes in heavy traffic and was able the vehicle to the outside emergency lane, finally coming to a stop.
Looked under the hood and saw oil dripping everywhere but with all the oil everywhere I could not find a prime source. Looked like the oil came from the top end of the engine and dripped down. Measured the oil at the dipstick and it seemed like I was at least a quart plus down (I checked the oil before I left on the trip). And it didn't look like any water was in the oil. And my radiator overflow tank was at the proper level. So I figured I lost all that oil during that period of "white smoke".
So had my vehicle towed home. Today in daylight, I did some more inspection and removed the air intake system (hoses and canister) from the air filter to the throttle body. There was significant oil up to the canister piece that fits on the air filter canister (but no oil in the actual air filter), and significant oil inside all the hoses up to inside the throttle body (up to the butterfly which I could see),
When I disconnected these hoses I noticed the blow-by hose connected to the intake hose system was not connected to anything. And a tube opening on the valve cover was open without the a blow-by hose attached and, with no clamp. So I assume all that oil and came out of that blow-by tube on the valve cover, (white smoke created by hot oil hitting the engine).
So appears to me that its not a blown head gasket or worse, which I first feared.
I have the vehicle parked at home.
QUESTIONS: So what are the suggested steps to troubleshoot and repair? Besides reattaching everything and putting a clamp on the blow by hose? And installing new spark plugs and plug wires. I previously replaced plug wires around 60k, even though the manual recommended 100k mile replacement. (And a couple yeas back I had the dealer replace the PCV, which was recommended in the manual and included in the warranty. The timing of the initial check engine lights appeared shortly thereafter).
Is there suppose to be a large amount of oil in the air intake system after an incident like this and should I try to clean/flush out the hoses and the inline canister?
When I disconnected the inline canister from the hoses in the air intake system, unfortunately I failed to document the direction which the canister goes. It has outside markings "ADP with a forward arrow with some horizontal lines, and then at the other end upside down markings with a greater sign PP less than sign. Should the forward arrow point toward the throttle body or toward the air filter (I'm thinking in the direction of air flow, toward the throttle body). I've taken some photos of the engine with air intake hose system unattached, if that might work...
View 2 Replies
I have a 02' Limited V10 with 202xxx and have come across new issues recently.
Occasionally when I start up the truck it spits out blue smoke BUT its only when it fires up then it's done.
View 6 Replies
How many of you have this issue with your 2010 5.4 puffs a cloud of smoke on start up I have 20,000 klicks on mine after 8 months....
View 7 Replies
