Ford F-150 - 1997-2003 :: Alternator Or AC Compressor Growling Noise?
Jul 21, 2014
I drive a '99 F150 4x4 5.4 EFI 196,000 miles. Recently I started noticing a growling noise that followed engine speed. I immediately thought alternator going out. So I pulled the belt off and it spins free and doesn't feel rough at all.
So I started it up and realized the noise got a lot louder when the ac clutch cycled. Now I'm thinking ac compressor. A short trip to my mechanic who didn't even really look at it very long and he said the compressor is about ready to seize up. I thought I might just put on an ac bypass pulley to get by for a while. Not really a sound decision in the middle of July, I'm thinking, but I'm poor and it beats having the compressor lock up, right?
Today, when I get off work and pop the hood with the ac off and the clutch not engaged the noise is worse than ever. I put a stethoscope (long screwdriver, I told you I was poor) on the alternator and it is making all of the noise. Turned the ac on again and it was really making noise now. So I applied the stetho-driver to the ac compressor and it is quiet as can be.
I am cautiously optimistic that the alternator is the sole culprit and that it only gets louder when the ac cycles because of the extra drag on the belt.
Does that seem like a logical explanation? Should I just try the alternator? I really don't want to destroy a perfectly functioning ac system only to find out that it was OK to begin with and I don't want to buy a $150 alternator for no reason either.
View 3 Replies
Advertisement
I have a 2001 ford truck and it makes a growling sound when i am turning right but is not when going straight ahead wondering what part in the rear end could be making this sound.
View 2 Replies
AC compressor makes a loud growling noise and lugs the engine briefly when engaged at idle and the truck has been sitting for weeks. After that initial grind, it works perfectly and makes no harsh noises. Can I replace the compressor bearing or should I swap out the entire compressor?
View 2 Replies
We have a 2010 Hyundai Accent, with low miles (10,000), and the A/C Compressor is making a "growling" noise. The only way to explain the noise is when you hear a human try to immiate the sound of a dog growling. That's exactly what it sounds like.
First thing in the morning it doesn't make the noise to much, but as you drive for a bit you will start to hear it. Sometimes it's really loud, sometimes quieter. When you shut the A/C off, it will continue for a few seconds then stop.
The service department told me it was the compressor and it is, "pretty normal on the cars." How is that normal though? It sounds awful.
View 9 Replies
Vehicle is 1998 F150 with 194k. The battery is 1 1/2 yrs old and belts and alternator are original.
Yesterday morning my VHF and dog tracking eqipment started humming with the truck running. The hum on the tracking eqpt. only happened when I pointed the antennae over the direction of the hood with truck running. When I shut truck off everything is normal. Later in the day the battery light came on. The battery light would go off if I kept it over 2400 rpm's. The charge on the dash was normal but as I got closr to home last night it dropped to almost nothing and the lights were very dim.
I am thinking alternator. What I am confused about is the humming noise in the background. The tracking eqpt. is completely separate from the truck while the VHF is direct to the battery with an iline fuse. Bad voltage regulator?
View 4 Replies
My alternator went out last week. I installed a new alternator, battery and serpentine belt. However, the battery is still dying. So far I checked the continuity on the fusible link and it appears to be good. I also checked fuse number 11 which provides power to the voltage regulator. The fuse is not blown. The voltage at the battery while it is running is less than 12 volts and it drops the longer it runs. I also have codes b1318, b1932, c 1226, and c1284.
View 8 Replies
For a little wile now, I have had a growling noise when I depress the clutch pedal with the engine running. It mostly does it when the truck is cold and goes away after a few uses but was getting worse and taking longer to go away. The transmission shifts normally, the clutch operates normally and it does not make the noise if I put the transmission in neutral and let the clutch out. So I'm thinking dry throw out bearing.
I did an oil change Monday, and while it was up on the ramps, I decided to check the transmission oil level, I mean its got a 181k on it so its about time to check, right. Bone dry. I put about 2 qts of gear oil in the transmission that the service manual says has a 4 1/4 pint capacity. I took it out for a drive today and the noise is gone. Go figure.
I only drive the truck one or two times a week, sometimes less so in a couple of weeks I will check the transmission again for a leak, but there was no sign of a leak when I was under there Monday. But is still shifts smoothly, makes no noise.
View 3 Replies
I have a 1998 f150. Was driving down the road the other night and the truck loses all power. I have replaced the alternator and the battery loght stayed on. So, I took both old and new altrrnator to parts store and had them both tested and they bith passed. Is this a commomn issue?
View 7 Replies
The other day the battery light came on. Of course the useless "gauge" still reads normal but that is another rant.
Checked voltages today:
Battery reads 12.0 volts key off, 11.83 key on, engine off, 11.65 engine running.
Obviously discharging and I am guessing it is the alternator. Do these trucks have an external regulator that may have failed or is it in the alternator? I'd hate to spend $150-200 for an alternator only to find out it doesn't solve the problem.
View 14 Replies
A co worker gave me an 1986 F-150 5.0 302 with 225,000 miles that he had sitting for 1 year in driveway. He never put the new alternator in that he bought. I towed it to my house and put the alt. in jumped the battery and it started but idle was horrible. turned the idle screw to get bad gas burned off.
Whenever I shut it off or it died from idle I would have to jump it. So, I put new 56-3 battery new relay and it started right up. Drove it down the road to test drive, the truck would want to fowl out whenever I stepped on gas peddle hard. I put Sea Foam and Lucas in the tank and 20.00 premium on top. but now the truck will not turn over since it was shut off unless i jump it but needs jumping all the time. thought it was the starter so, replaced that and still tick, tick, tick, tick when trying to start won't turn over. Its going to start to make me drink, what I can replace now or have checked? maybe its the Alternator he gave me with the truck?
View 3 Replies
Alternator warning lite comes on at idle rpm. Speed up rpm lite goes out. The gauge shows alternator is charging. Autozone checked it for me it is putting out 11 to 11.5amps running. Should be putting out around 13 amps, right? alternator bad?
View 1 Replies
I have a 99 F150 4x4 with 5.4 Triton, 99xxx miles. I was towing my boat when the regulator in my alternator went bad. I drove the truck with the voltage being sporadic for about 10 miles until I could get to a parts store. While driving on the bad alternator, I started noticing a misfire. I replaced the alternator, battery and DPFE. I still have the misfire....but here is the kicker. The misfire only happens when the truck reaches operating temperature. Which, in my limited knowledge, eliminates a fouled plug, COP, bad injector and a vacuum leak. I've got no check engine light so I can't pull a code. The only thing I can think of is to clean the EGR?
View 10 Replies
I have a 2000 V6 F150 and replaced my alternator in about five minutes and now have been trying to re-install the serpentine belt for about 6 hours. How do you grab the tensioner pulley?
Also I selected the 130 amp new manufactured alternator at Advanced. Auto thinking the 130 amp might be somewhat of an upgrade to my original Motorcraft Alt and after several hours I also discovered them. pulley on the new alternator is about a quarter inch larger in diameter than the original alternator. I wonder if I should compensate for a half inch longer belt or try to get the same one on.
In any case I cannot find a way to grab and move the belt tensioner to allow me to reinstall the belt around the alternator. Are there any pictures anywhere on how to move the tensioner to create slack when reinstalling the belt?
View 11 Replies
Got a 97 ford explorer sport that wont start. It will go like its going to start but I've only got it to run with ether then dies got new battery n tps thinking its the alternator because i hear a ticking in that area and the battery is now dead after i charged it all the way up granted. I did try consistently to get and keep running?
View 3 Replies
I bought a 99 f350, that already had HID's in it, i found out i was running the wrong batters (weren't 800 cold crank) I just had to replace the alternator. Ever since the new alternator when i turn on my headlights my truck shuts off. IT fried my IDM and i just put a new IDM and 2 new batteries in it today. Thinking i had fixed the problem i drove around no issues, finally i was leaving someones house and turned on my lights, and truck shuts off!!! It restarts but now im trowing a code!!!! im guessing the HIDs are wired wrong and that's why its shutting down the truck but OEM IDM from ford is 1300$!!!!! brand new one installed today,
View 5 Replies
I have a 2001 f350 7.3 diesel, I am looking at switching out the air intake? Also, I have an issue with the code for a dual upper and lower generator fault.. I checked and only have one generator not a dual system.. The alternator is running strong at 14.1.. But I have noticed when I start it up it is down to 12..
View 1 Replies
I put a re manufactured alternator in my 2000 f150 with the 5.4 liter. Now all the lights flicker, go dim and then come back on bright again. I noticed when the lights dim, the heater fan speed also drops. The light flickering is constant and bad enough, that I can notice it in daylight also with the headlights on. It is really noticeable at night with the truck in drive (or any gear for that matter) sitting at a stop sign or sitting still in my driveway. I changed out the old alternator because it was making a loud chattering noise. I didn't have any trouble with the lights or fan with the old alternator. Why doesn't the battery volt gauge in my instrument cluster fluctuate all the time while it is doing this? It reads in the normal range all the time and doesn't move. The flickering lights are also noticeable at highway speeds, its just not as bad.
View 2 Replies
So today, I planned on switching the belt, idler pulley and tensioner since at least two of them are making noises. After taking all of the stuff off, belt, idler pulley and tensioner... and since I always compare parts I buy to parts that were in, making sure they are identical and I didn't order the wrong one. So first up I checked my tensioner and the position of them or angles are different, completely different.
So Google it to view a few diagrams and bang! it hits me... the one I took out from my F150 is for a non-AC... so back into the truck and I'm looking. Didn't have to go far when I realized that my AC compressor is missing!!!!
I keep looking around and I see that yes, I did have AC in it before I got it; because the guts are there but sliced! Great, so the job went from easy and easy I mean buy compressor and install; but now since the guts were cut, the PO sliced the thing out simply put.
1.) What are the bolt sizes that hold the compressor in place?
2.) Is there a wire connector on the compressor? or no?
View 1 Replies
I have a 1997 Ford Expedition, 5.4. My research indicates that fuses 2. 19. 29 are associated with the instrument cluster (IC), could you identify their specific function in relation to the IC? My IC gauge lights are not showing and my alternator is not consistently charging. The blinkers, battery, oil, brake, and ABS indicator lights are showing in start. Regarding the alternator, my research indicates that a failing alt light on the IC may cause the no charging condition? As a note, I have a brand new battery, brand new alternator, brand new 3 pin wiring harness. Also, when the alternator is not charging and I connect the a jumper from the exciter wire directly to the pos battery terminal, the charging starts.
View 9 Replies
My AC compressor failed so I replaced it.
I put in 1 can of R134, and I don't see the compressor cycling.
How do I remove the connector to the accumulator so I can jump it and force the AC to run.
View 3 Replies
I have a 01 f150 4.2L and a while ago the ac compressor clutch broke. I didn't catch it in time and the stress it caused on the belt broke the power steering pump pulley. So I replaced the steering pump and pulley and the compressor the accumulator/dryer and the office tube put the 134a back in and everything worked fine. three months later ac stopped working. I figured the condenser was bad so i replaced it. Charged it up still no cold ac. so i thought maybe the manifold that goes on the compressor was clogged so i replaced it. While I did that i said to myself well i should tear out the dash and replace the evap as well. so just about everything has been replaced on the ac system.
Aside from the cycle switch and the high side switch witch from my test both seem to be working. now here is the thing. the tube witch holds the office gets ice cold then goes to the evap but the suction line coming from the evap doesn't get cold and the ac blows warm air. this very problem is what convinced me that the evap was clogged and needed to be changed witch is why i undertook the task of tearing the dash out. in all it took 14 hours to do the whole job. now for the pressures that i get from the ac manifold low side goes 40 down to 20 ..... this is normal. high side is a little high. I charge it to 125 still no cold air. so i dump a little more 134 in. at 90 degrees high side pressure should be around 200ish i get it there still no cold air. I have just about replaced everything i can think of.
View 7 Replies
