Ford F-150 - 1997-2003 :: 5.4 Stalling In Drive Only / Reverse Works Fine
Mar 29, 2013
2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
View 5 Replies
Advertisement
So my aunt has a 2002 ford f150 king ranch 5.4l and a night ago it started this problem which when you put it in drive which she has to put it in 2nd for it when she pushs on the pedal it will rev up to 2500rpms than jerks and goes and its usely fine till she stops than goes and it does it again...
Than today it wouldn't even go in anything but reverse... So than we herd about the Range Sensor on the side of the transmission and it seems like it was it so I unplug it when it was running and when i push on the pedal and it revs up to 2500rpms it will go forward and have power. So we went to get a new range sensor after like 4 hours trying to get the dam thing off and another 2 to get it back on.. I started it up and only reverse works again... So I unplug the harness to it again and we got the gears but 1st and 2nd will just rev and go.
We at a lost right now i even tighten the shift screws under the dash cause our expedition was loose at one time and the gear shifter was loose like hers. But even tighten the bolts it still don't fix the looseness or even the gears.. Is this a transmission problem? OR even the torq covertor?
View 4 Replies
Was going to leave the other morning and put it into reverse and nothing happened. Tried every other gear and works fine. Reverse is the only thing giving me problems right now. Tried doing some research on my own, because I can't afford a tranny rebuild. I was hoping it was either the solenoid or low/reverse band. I don't know about the band, because it works fine in low2 and low1....
View 2 Replies
I have a 78 f100 2wd, 300 inline 6 and I've put 2 c6 transmissions in it. The transmission shakes real bad in reverse. When you put it in drive and try to take off it wants to quit pulling but when you put it in first gear and shift up to 2nd it works perfect. My plan was to just junk the C6 and switch to a manual trans but I don't know what trans I would swap it with.
View 8 Replies
I recently got a 2wd 1994 150 straight 6 4.9L, It's been a great truck so far. It drove from New Mexico to California with no issues. Just this morning it started stalling and dying when pulling up to stop lights and putting it in reverse. The truck has 172,000 miles and has a new serp belt, alternator, radiator, and starter. It seems to run just fine on the highway and once it's warmed up it doesn't stall as easily. There is an exaust leak.
View 1 Replies
I have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 Replies
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 Replies
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 Replies
I was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 Replies
I have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 Replies
I have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 Replies
Very strange problem for me especially since it's not my car, belongs to my sister. Only code that was set last month indicated the MAF so I cleaned it and the car ran fine. Started to hesitate up hills (steep uphill driveway) so I replaced the fuel filter yesterday and my sister said it drove just fine uphill. Now it stalls whenever put into drive, no codes set and none pending. It will idle in reverse but not in drive.
View 1 Replies
It appears electrical. With it running and this first symptom usually guarantees that it will stall. You go from park to reverse or drive the speedometer needle will begin pulsating. I have notice if this is not happening it won't happen. Next standing still but in drive or reverse if you turn the heater, radio, lights or the AC pump kicks on. Boom the car stall and almost act like the key switch was turned off then back on. It also has happened while moving but it does not stall but all of the dash light pop on as if you just turn the car on.
View 3 Replies
Why my 03 focus zx5 will stall in reverse. I have had the tranny serviced. I can drive it and then let it sit for about an hour and then try to reverse in it and it dies. I have change the mac, tps, iac sensors. I am at a loss for why this is happening. I also changed the pvc hose that runs from the back of the motor to the pvc valve.
View 14 Replies
B1602 PATS Recieved Invalid FMT/Key CD
P0753 Shift Solenoid A Electrical
P0758 Shift Solenoid B Electrical
P0740 Torque Converter Clutch Fault
P1760 Pressure Control Solenoid A Short
p0305 Cylinder 5 misfire Detected
P0316 Engine misfire Detected on Startup
The Trans will unlock while driving for a few seconds then lock back up and drive fine, it seems to be worse over the past couple days. It is no different cold or hot. I also noticed the head lights dim and the voltage on my scanner drops to around 12 volts when the trans disengages. When it is not acting up it drives and shifts perfect.
I have checked a few grounds that were visible and cleaned battery connections. The misfire code has been fixed, not related.
View 12 Replies
I have a 1997 ford aerostar van that i recently acquired through some family,when i got it it was running fine but has recently started having troubles.The Question i have is this i put my car in drive or reverse and push the gas pedal the car doesn't move.....we have tried putting transmission fluid into it and that worked temporarily. What it could be except just a bad transmission?
View 2 Replies
I got myself a 1997 explorer Australian model when I got it (here's the problem) if you put it in drive it will not engage but if put in first will drive normal then shift into second all good now u have push O.D then shift into drive all good (unless u slow down to almost a stop) ? New problem is, it has gone and lost reverse, put it in reverse and it engages with a small clank (normal) but just slips with any revs. I have read posts here talking about upper and lower valve body gaskets and transgo shiftkit which I have ordered but do there maybe more parts needed? Cause it's going to cost me lot just to put transmission fluid back in.
View 4 Replies
This just started happening last week. When I put the truck into reverse, the engine lugs down and dies. It' as if the AT is fully engaging reverse gear with no clutching action. If give the truck a bit of pedal, I can put her in reverse and back up without issue. Going forward into Drive has no issues.
View 8 Replies
So after work tonight I went to start truck it turned over fine but wouldn't start, when it finally did it barely ran and then it was fine, I had it b4 when I start it would turn over for a little bit b4 starting, would that be fuel pump?
View 1 Replies
I have a 1997 Dodge Dakota V8 (automatic) with about 140k and live in Vermont. Recently, my truck will konk out while I am sitting at a red light. As I'm sitting there, the RPM's keep going down below 700, until finally stalling out completely. When I shift into Park/Neutral then turn ignition, it will start right back up again. To get around this, I have been shifting into Neutral while I wait at the light, then back into Drive when it turns green. I have recently installed a new battery and exhaust system. I am wondering if this is occurring because of worn plugs, a dirty air filter, cracked vacuum hose, or bad alternator?
View 2 Replies
We have a 2003 Ford F250 Super Duty, gas engine. This will start fine, then a day later, it won't. Wait 30 minutes, then it starts.
Starter and battery are fine. It acts like it isn't getting fuel. Fuel pump? Filter? What else might cause this?
View 2 Replies
