Ford F-150 - 1997-2003 :: 2002 Truck Started To Idle Very Rough - Codes PO308 And PO316
Mar 6, 2012
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 Replies
Advertisement
These are the code that keep spitting out. I have a 2002 f150 5.4L supercrewand it is running rough. I had this problem about 3 months back but i didnot get any codes from the computer i washed my truck a 1/2 day earlier, 2days later it went away. this time it has spit out 4 codes a po306/po307/po300/po316. the po307 and the po300 are gone, but the other two remain and it is still running rough 2days later. i had just washed my truck 30min. before, it started happening, is there water somewhere? My dad (long time mechanic) says use wire dry on the cops and it will go away. I have read other post on misfiring and I am still not sure what to do?
View 10 Replies
2001 F150 4.6. Just replaced all 4 oxygen sensors and spark plugs. Replaced rubber grommet on brake booster as it was leaking vacuum.
Truck is still running rough hesitating.
Pulled codes came up as PO141 oxygen sensor heater circuit. PO171 passenger side cylinders running lean. Fuel trim outside limits.
View 9 Replies
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
View 2 Replies
1999 Ford F-150 V8 5.4L... The other day I was attempting to fix my 4wd. I discovered that the vacuum tube by the 4wd solenoid had become disconnected. I reconnected it and in an effort to see if my fix was successful, I drove my truck up one of the canyons nearby. I got to an area full of loose rock and popped my truck into 4wd. As soon as I began to drive, the truck started idling very rough and died. I attempted to restart it for the next few minutes unsuccessfully. I got it started once and it continued to idle rough for a few seconds and died. I have not been able to start it since. It turns over but will not crank. It is not throwing any error codes. What I have checked so far:
Spark plugs are working.
When turning the ignition into the ON position, I am able to hear the fuel pump working.
I have not seen any cracks in the vacuum hose.
All the fuses are still okay.
What the culprit may be?
View 2 Replies
Sometimes the truck is hard to get started and to keep running, Once it warms up it will run fine. The next time it is started it will start fine but when you are going down the road if I try to accelerate it will start backfiring and not pick up any speed. I am getting a lean code on both banks. I have changed the IAC, the throttle position sensor and mass air flow sensor. 2002 F150 with 6 cyl
View 1 Replies
I have a 2000 F150 4.2L and I have 2 codes PO304 & PO174 so far I have changed my plugs & wires,fuel filter,mass air flow sensor, and coil pack...it is still running rough under a load and a little rough on idle..
View 9 Replies
so i bought this truck about 3 months ago and it was running real bad when i got it, I went ahead and changed the lower and upper intake gaskets, cleaned throttle body, egr ports on lower and upper intake, did timing chain cover gaskets and 3 bad injectors i found while doing gaskets, truck ran better but still black smoking(running rich) and getting 8 mpg. So I changed fan clutch,fuel pump fuel filter,airfilter,MAF sensor(old one was pulling 14.4 volt), DPFE sensor and all 4 oxygen sensors(old ones carboned up and real sooty).
I've checked my egr valve while idling and when it opens the engine just about stalls, truck seems to be running better but CEL light came on again and is throwing these CODES:
P0453 (evap emission ctrl sys pressure sensor high input),
P0141,
P0153,
P0135(oxy sensors),
P0401exhaust gas recirculation flow insuff detected,
P0460fuel tank level indicator circuit error.
And I believe I've told everything i know ...
View 10 Replies
2002 F150 5.4 v8,,, I had troubles just over a month ago with a po305 code. i got the truck fixed with 2 new coils n some gaskets. I am having these po353 & po171 codes pop up now. The truck is running rough and I am curious to if its just another coil problem or if their is something I am overlooking or just don't know about?
View 1 Replies
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
View 14 Replies
So I recently acquired a 2002 F-150 4x4 super crew with the 5.4 V-8. It idles rough (surging from 400 - 700 rpm) when cold, and sometimes dies, but more often then not it stays running. It runs and drives fine when the accelerator is pressed and when going down the road. When it gets up to operating temperature, and has been there for a while, it seems to idle fine 95% of the time. The codes I have are P0136 (bad circuit to O2 sensor), P1151 (HO2S detects lean mixture or something like that), and the infamous P0171 and P0174, which is lean exhaust/mixture on both banks. Now I have read extensively on the internet about these symptoms and have done the following:
Sprayed every vacuum hose with carb cleaner, and even around the intake manifold and injectors.
Considered the IAC (its new, the guy I bought it from replaced it a couple months ago) Torque app for android phone says vacuum is good. Cleaned the MAF and air temp. sensor with electrical cleaner Checked all of the vacuum hoses on the engine by pulling them off
Put grease around the fitting where the PVC valve attaches to the valve cover. Seemed to make it idle a lot better after messing with it, but I don't know if it was a result of the engine being fully warmed up, or my messing with the PVC.
What to try next? I'm close to just dissecting the top part of this engine and seeing what the intake manifold gasket looks like..or could it really be an 02 sensor?
View 3 Replies
I've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......
View 7 Replies
I have a 2002 4.6L FX4. When I run the A/C for an extended period (say 15-20+ minutes), it will start to cough and sputter and eventually just die. It will restart but run rough and cough, sputter, die.
If I turn off A/C and let it set a while, it runs fine. No check engine light. Possible EGR problem????
View 3 Replies
I have a 2002 f150 with the 5.4. Its got a rough idle and a bit hesitant on acceleration. Im wanting to replace the coils and plugs but what brand of coils should I use?
View 3 Replies
I have an 01 SuperCrew with the 4.6L and it's idling really rough. Last summer, the idle started to flux pretty bad with the a/c on and eventually, it started to spray coolant mix through the vents and I lost heating about the same time. So, local dealership changed out the heater core and that is working again.
Well...I still have the idle flux, it fluxes from between 400-1000rpm at idle with the a/c on, it's a constant flux....up/down/up/down/up/down. A/C off and the idle is rock-solid steady. Dealership has changed 4 ignition coils over the last couple of years along with an EGR or PCV (whatever it's called) valve as well, none of which was for the idle problem, but somewhat associated. Where I should be looking?
View 2 Replies
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 Replies
2003 ford explorer 4.6L. This truck will start and run rough high temp low oil light come on and temp gauge is pegged hot. Oil gauge is fine though, checked oil its fine.
I checked coolant reservoir its ok.
If I shut truck off and restart it will run ok and rev like normal and then all of a sudden go into limp mode and will misfire etc...
What sensor seems to be the main culprit?cht sensor???
View 1 Replies
2002 Prius that idles really rough for a min or two when first started. Recently got check engine codes 300, 301, 302, & 303 for misfires. Also have had the red triangle with a 3191 fail to start code. When I get the 3191 it will start after a couple attempts. Mileage has dropped to mid 30's. 227k miles & other than the idle problem the car runs well.
View 5 Replies
1997 F150... Truck has slowly started getting worse and worse performance. About 3 weeks ago the truck started rattling from the exhaust, Towing my trailer the other day, the truck had NO power, I thought it was the plugs, so I replaced them.
Now the rattle is worse (no lose heat shields). I am blowing the little tubes off the drivers side exhaust manifold, the ones that go to the DPFE sensor.
Did I mention, that the truck has no power, sluggish, now I am dumping hot exhaust fumes into the engine compartment. Still got the rattle underneath.
I think the cat is plugged up on the drivers side. (which probably explains all my symptoms)
Any other reason for the rattle literally coming from the drivers side cat and the little tubes being blown off?
View 14 Replies
I have been having odd problems with my truck for several weeks now and what the problem may be. Occasionally the truck will not start. This happens after it has been run for an errand or to church. The truck turns over but no ignition. Sometimes if I pump the gas pedal very quickly I can get it to start. Other times I have to sit and wait about 5 minutes. I have gotten the following two error codes - P1506=Cylinder Head Temp Sensor and P1299=Idle Air Control Overspeed Error. For two days the "check engine" light was on, but now it has gone out. I have searched for an answer to this problem on these boards and one possibility may be a vacuum leak. Is this the most likely? 1998 Triton 4.6 ....
View 3 Replies
I have a 1997 Explorer Sport 4.0 SOHC, 110,000 miles. When I start it in the morning or after sitting for a few hours, the idle is very rough. Most of the time it wont even stay running. My first thought was a vacuum leak. I found four leaks and repaired them, including the EGR valve control and the EGR solenoid. One stem on each was broken off. I bought these parts from the dealer and then tested the vacuum, which I now have vacuum pressure. The check engine light is on and doesnt read the "system evap emission control pressure sensor low" (vacuum leak) anymore, but it now reads "system too lean (bank 1) and system too lean (bank 2). I cleaned the IAC valve and have ran several bottles of injector cleaner through. My mechanic thinks it is the IAC, but when you disconnect the plug on it, the car will barely idle, so it must be working at least a little. I have seen suggestions for a fuel filter, which I am going to replace, but I am really lost here.
View 14 Replies
