Ford F-150 - 1997-2003 :: 2002 - Starter Did Not Turn Or Crank The Engine
Sep 9, 2014
I have an 02 f150 5.4 4x4, drowned it a while back, thought i had hydro lock, crank can be turned by hand though as far as i can with a wrench, so internals seem to be fine, no bent or broken rods that i could tell, ripped everything apart cleaned it up put it back together, new fuses, new ignition relay, new starter, alternator and battery as well, turned the key to on and got all my electronic stuff back up, turned to start and it all goes dark, which i assume is because at that point its sending power to the starter, but the starter didn't turn or crank the engine...
So question being when i put my new starter on is it possible that i might have crossed a wire or something that would cause it to not crank? and due to the fact that I had water in it, and had hydro locked it, all my plugs are out, now I know that spark is needed for the engine to run, but shouldn't be needed just for the crank to turn right? question being is that once i fix the wires on my starter, I am looking for initial crank before start up, so do i need to put a plug or two back in and hook them up to make it crank? or will it crank without them? and yes I did replace all my fluids as well.
View 8 Replies
Advertisement
I just got a 1998 F150 5.4l 4x4 autotragic. Was sold to me as needing trans, wouldn't start. Tossed in a new starter and solenoid, now I can hear the the starter turn crank pulley turns maybe a quarter inch and when I let off the starter it goes back to the same spot.
Fear is motor is locked, but question (i don't know automatics) is there any way that a bad trans could keep a motor from turning over? Truck rolls in neutral or drive, pulled the drain plug no water just oil. Tempted to just buy a running 5.4 with trans but if I can avoid that I'd prefer to.
View 3 Replies
After short trip, 02 f-150 v-6 will not crank every time but engine turns over. When it does crank, it runs fine the entire trip. 189,000 miles on motor and is a 4x2 extended cab.
View 1 Replies
I am working on a 2000 f-150 XLT 5.4L 4x4 Automatic. It tries to crank over but acts like its stuck. things done: New starter, new battery, fixed connections. I can turn the crank counter clock wise but won't turn clock wise. Not sure if i should say the engine is bad or could trans be stuck? Heard 5.4L's have timming chain issues. Is that true? Point me in a direction and i'll go forth.
View 14 Replies
My 2002 F150 Screw has been giving me issues when trying to start it for the last month. Sometimes it will start sometimes it won't. When I turn the ignition on the gauges all seem normal, the theft light turns solid then goes out, but engine will turn over but not start. Sometimes it will start if I leave the ignition on for 20 seconds then pull the key and try again. (this doesn't always work). I have disconnected the battery for about 2 minutes this usually works but not always.
Sometimes it will start first time with no issues. Once the the engine fires it runs fine. Another symptom is when I shut the engine off, pull the key and open the door, the chime telling me that the key is still in the ignition sounds. (but the key is in my hand)
I put a new battery in yesterday to rule that out and because the old one seemed to be getting weak. (starting issues didn't go away). I don't want to put 300+ into a fuel pump without being sure that's the problem.
View 1 Replies
I am having some weird issues with my 2000 F150. When I turn the key all the dash lights go out and no start. Ran 2 wires from the solenoid to a switch and it will eventually start. The starter will start real slow almost like the battery is almost dead and then speeds up more and more till it eventually starts. After it starts the theft light stays on the whole time. At this point I have no clue what is going on.
View 1 Replies
1997 Toyota Camry V6. The car won't start, the engine won't crank. I've checked for 12v constant at the starter and that's good. Next I checked for a 12v trigger at the starter. That wasn't present at the starter.
I went to the starter relay. Pulled the starter relay and tested it by applying 12v across two terminals and checked for continuity across the other two. It checked fine.
So I checked for constant 12v into the starter relay, that's present. Checked for 12v trigger into starter relay, that was present also. Next I jumped 12v through starter relay terminal into the starter and the starter cranked the engine. Next I checked for ground into the starter relay, I didn't have continuity.
So I'm guessing it's either a bad ground wire coming into the fuse box or maybe even a bad fuse box? Is my thinking correct? Or is there something else that it could be? Maybe a main fuse or something, IDK, this is the first time I've encountered a problem like this.
What wire is the ground source for the starter relay? I found a wiring diagram from Chiltons (which I've attached to this post for reference) but I'm not really sure which wire is the ground for the starter relay. I don't have the car or relay in front of me to look at the terminal numbers.
View 12 Replies
I have 98 f150 with 4.6 starter went so I put a new one on wich was a hassle and it tries to turn but just wont as if the motor is seized. I had been hear a loud howling sound from what I think is the ac unit and the ac line burst after trying to start. Would a bearing or something with the AC be enough to stop the engine from turning over? Or could it maybe be a wire connection problem? To me it sounds like a starter trying to start a seized motor but I cant see that my motor would be out it only has 190 000km and the oil looks good. but we couldn't turn the motor over with a ratchet? The truck had been getting gutless. I am stuck...
View 4 Replies
After getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 Replies
I'm having some strange electrical issues b where to start fixing the problems. Here is whats happening:
- Put the key into the ignition and turn to the "on" position, full power to everything no issues at this point
- Turn the key to the start position, get 1 click out of the starter and then lose all power to everything
- Turn the key off and back to "on" position, sometimes I get power at this point and sometimes the power stays dead for a while
- Check the battery, which is good (12.3 volts)
- At one point someone noticed some sparks coming from a connector near the back of the firewall on the passenger side (sits on top of a metal cover with a large positive terminal right behind it). I've disconnected this terminal, cleaned it and put on some dielectric grease all of which hasn't done anything.
- Basically I mess around with few things, check some connectors, let it sit for a few minutes and then it will start.
View 5 Replies
Camry 2002 LE (4 cyl Auto), 140K mi
This morning, for the first time I can recall, the car would not start right away. Had been sitting in the garage for 2+ days. Starter would crank just fine, but engine would not fire. No lites were left on overnite. Finally (after about 6+ attempts), engine started -- runs fine now.
Took it to TOY dealer. Their diagnosis: weak battery, alternator low output.Happy, had recently (6 mos) replaced battery after 4 years of use, so got a new battery N/C.TOY ran a charging system check and it shows "Alternator Condition: OK" (midway between shitty and great I recall).
Funny, but my first thought when it would not start was the fuel system (fuel pump) or dirty ignitors. I did ask my regular mechanic for an opinion, and he thinks it might indeed be the fuel pump -- perhaps a clogged filter.
View 2 Replies
I have a 2001 supercab 4x4 with a 4.6 in it, it has 186k on it and the only issues I've had was a misfire not to long ago. I replaced the plugs and coil packs and fixed that issue. 2 days ago she ran fine with no issues and this morning I went out to go to the store and she wouldn't start. All the dash lights come on and all of that normal stuff when you turn the key. When I turn the key I hear what sounds kind of like a clunking noise towards the bottom of the windshield and the middle of the dash. The starter does not engage, no nothing, really confused here. I thought maybe the battery was bad so I put my jumper on it and tried but again nothing happened.
View 14 Replies
If I turn on my ignition switch and my gauges go to where they're supposed to be, the truck will crank. If I turn switch and , lets say gas needle for example, the needle goes to full then drops back to empty, the engine will turn over but will not crank.
View 2 Replies
Ford F150 truck, when starting, the starter will turn over strongly for half a second then just abruptly makes a loud noise and stops. It won't ever fully crank. Is this just a bad starter?
View 2 Replies
Having problems with the truck - either a no crank situation and now a complete shut down while driving at any speed.
Dash is blank with no power when truck shuts down, here is the hitch with the no crank, I pulled and replaced the PCM module and the truck fired up without hesitation. I had to do this a few times over the course of today to get home. I can live with having to do that for a while but it is unnerving to have the truck shut down with 0 notice.
Throttle body was just cleaned, and all starter/battery connections cleaned and protected. Brand new PCM relay. What does this relay have to do with reset, for clean start up after removing it and then just putting it back in it's place? Would there be any solutions for the dies completely while driving, or fails to crank?
View 7 Replies
I have a 2002 F150 5.4L (VIN-L) that has been sitting in the driveway since February. I have been a mechanic for 30 years for large commercial trucks, and my own truck has me stumped. I'm sure I've forgotten something but I'll try to list everything I have tried so far. It started with crank no start, no check engine light, checked for trouble codes got a trouble code for the CHT(cylinder head temperature) sensor.
- Replaced the CHT sensor. Cleared codes.
- Dash lights up fine, shows mileage, and anti-theft is not flashing while cranking.
- Fuel Pump does not seem make any sounds. Hit the tank with a hammer. Nothing.
- A little fuel comes out of the schrader valve on the fuel rail when I push on it. I have not checked it with a pressure gauge.
- Attempted to start with ether, nothing, so I'm assuming no spark.
- Fuel pump inertia switch isn't triggered.
- Checked several ground connections to the frame and checked ground connections in the PCM harness. All have less than 5 ohm resistance.
- Unplugged and plugged back in cam shaft sensor.
- Checked voltage on the TPS(throttle position sensor) I'm unsure about the results, if the TPS was bad wouldn't it just idle funny and/or stall?
Fuel Pump and PCM relays in the underhood fuse block appear to be good. All other fuses and relays appear to be good. I have been swapping the relays with one I think is good, although. Searched all over for additional relays, and found 3 inside the cab behind the passenger air-bag. Can't seem to find anything in the Haynes/Chilton manual that lists what they do. They are about half the size of the fuel pump relay.
Manually grounded the fuel pump relay, relay clicks but I don't hear a buzz from the fuel pump. Id like to run 12V to the fuel pump directly to see if that's my issue, but I'm not sure where to connect it without frying something important.
I bought the alldata.com DIY guide for my truck and it hasn't worked much. I have read extensively about others with similar problems and I just don't know what to do next. My main question here is, if the fuel pump is bad, would that stop the spark plugs from working? I'd rather not replace the fuel pump without being absolutely sure.
View 3 Replies
I have a 99 f150 2wd v6 4.2 liter engine. Im going to sum up what happened and what I've done so far. One morning truck wouldnt start. Wouldn't crank, turn over, or even make a click click noise. I tried jumping it just to be sure but it didnt do anything. Battery is fine, interior lamps, displays, and radio all work fine.
I took the starter off, had it tested, it was bad so i got a new one. Still had the same problem. Finally, i got underneath the trunk and bridged the positive and negative on the starter solenoid and it fired right up. So the starter is not the problem.
Next I looked into the starter relay, if I bridged the positive and negative on the starter relay it fires right up just like the starter. But since that is only bypassing the starter relay, it didnt tell me whether the starter relay was good or bad. So I got a new starter relay and it worked! It started with the key with no problem 3 times! I thought the problem was fixed but when i tried to start it an hour later, nothing... Same problem as before.
I checked all my fuses, none were blown.
I'm under the assumption that either something leading to the starter relay is making the starter relay go bad OR there isn't enough power going to the starter relay. Maybe something in the ignition, even though my accessories are all still working.
It is the only vehicle I have to and from work. For now I am getting by with bridging positive and negative on the starter relay to start it but that is only a temporary fix.
View 8 Replies
back story but may have nothing to do with problem. battery terminal bolts were rusted solid so i cut them off and replaced. truck stated fine the last time i started it before doing this.
I turn key and get a single click. i tried jumping 2 large poles on fender solenoid and still one click no crank. i had taken off the starter and autozone tested and it passed. i checked voltages everywhere i could think of and all were as to be expected.
could it be the starter even though it passed?
View 5 Replies
I have a 1998 F150, had this truck for just shy of 200,000 miles, never a major problem and now she's killing me. Turn the key, no crank,no start, the same time this started the radio also quit working. I can start her with a screw driver at the soleniod (new by the way) runs perfect after that. By the way it's a 2 wheel drive with the 4.6 v-8
View 1 Replies
I'm a relatively new F150 owner (just got rid of the 98 Ranger I drove since 99), so I thought I'd check in to see if I was overlooking something obvious. A few days ago, after driving to the store with no obvious issues, I went shopping (coincidentally for oil change materials) and when I returned to my truck it would not start.
Here is a bit of info:
Starter cranks over the engine.
Battery is relatively new, and has plenty of power.
I can hear the fuel pump kick on briefly.
Check engine light is on (EGR Valve fault).
Engine started with starter fluid.
Engine ran like normal after starting.
Finally, the vehicle started/ran fine for a few days before the issue occurred again.
Like I said, I'm not too familiar with the vehicle yet, but I'm assuming the issue must be with the fuel delivery system. I plan on replacing the EGR valve, but I am curious whether a faulty EGR valve cause a no start? Also, I'm wondering if it's more likely that the fuel pump is going bad, or something electrical is the problem since I'm under the impression that the engine stops sending fuel to the cylinder if/when the engine doesn't start quickly after turning the key.
View 6 Replies
I Have a 1998 f150 4.6 XLT and recently it has been starting on and off. sometimes i will try and start it and wham! it starts right off. then other times I just here the starter hitting and engaging but nothing. Replaced the starter, solenoid and still nothing. It does have an alarm system but the alarm light doesn't come on, also had battery charged and its working fine. I am really fed up with this beautiful looking POS. Oh and the wiper motor needs replace.
View 5 Replies
