Ford F-150 - 1997-2003 :: 2002 - Slight Missing At Idle
Apr 28, 2012
I have 2002 f150, fx4, ext cab, 110000miles 5.4 automatic truck, i just replaced my spark plugs, it still have a little miss, thought spark plugs will resolve but its the same, im wondering if i should change O2 sensors? clean EGR Valve? IAC valve? i am not getting good gas mileage and maybe its this missfire or something, its runs good without any problems, just this slight miss makes me think if its the cause to bad MPG.
I tried to find threads with pictures of how to change O2, how to clean EGR, and IAC, i remember seeing these threads but cant find em. And you think these three things will resolve my MPG and the slight miss?
View 14 Replies
Advertisement
it's missing at an idle and it acts like it dont wanna take gas but once you get it going on the road it does good. the motor is a remanufacture motor it's only got 6,000 miles, new coils, plugs and wires, cam sensor, crank sensor, idle air control, mass air flow,and temp switch.
View 9 Replies
I have a 2002 f-150 4.6 that sometimes has a miss upon acceleration but not all the time.the truck is a 4.6 with a manual trans.has no engine codes and scanner never show a misfires but sometimes it does , have replaced all spark plugs and coil boots twice.
View 4 Replies
97 f150 4.2 ... Got a pickup awhile back and was smoking excessive mostly blue. Pulled the motor and had exhaust valve with hole in it and intake valve not seating on separate cylinders. All new gaskets and put back in truck. Deleted catalytic since they were both destroyed and cleaned muffler as best I could. Now it smokes but mostly white when revved up and maybe slight blue at idle. It's not using coolant or oil but went through five gallons of gas in short time.
Tests I have done : Checked fuel pressure and holds 38 psi all day. Tested maf o2 sensors, one is bad and tested vacuum and compression all good. It seems to be over fueling to the extreme. idles a little rough and will backfire on occasion. No check engine light but had all the o2 sensor issue codes. I'm leaning toward bad PCM... Would that cause the smoke rough idle and super rich condition??
View 14 Replies
2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
View 3 Replies
Noticed my 2002 F150 had a very slight vibration in the seat / steering wheel when cruising down the highway at 60 MPH.. Very slight, but was not there 2 weeks ago.. It seem to get a little worst as the 2 weeks progressed. Got all 4 tires balanced and rotated... no luck...Took both rear wheels off-- no problems with tires -- checked bearing clearance-- pushed and twisted on driveshaft yolk to check pinion bearing... nothing found......... last resort was drop back end of driveshaft and check U-joint.. It was tight and dry. Put drive shaft in 12 ton press and pushed out the u-joint bearings. Very dry and joint pins were starting to spall....... I mention this because I had checked " clearance" and "slop" and had "no noise" before removal... Truck has 139K miles on original u-joints .......... Something to keep in mind. Eventually it would have worn to the point that it was obvious, but in the first stages of failure, you just get small symptoms.
View 7 Replies
My friends truck is having a problem, and I haven't found any info on the specific issue. when you shift from P to D and accelerate, there's a slight grinding clatter in the tranny i think, bump it to 2 and the noise is completely gone! pull it to 1, and there she is again, also in reverse it does this, speed is not a factor, only the specific gears. i had read a thread which mentioned a "sun gear", and also that 1st and R are on the same bands?
I believe it was for a manual tranny that I had read about, but what this could be?! he's got a slight drag on the rear brakes, i assume it's his E-brake, could that have caused a transmission failure? We've removed the driveshaft and checked u-joints and all, nothing there, but when the truck reverses on the ground, you can watch the driveshaft bounce like it's binding. We grease the slip joint while we had it off, and we were able to spin the rear wheels by turning driveshaft w no problem while off the ground.
View 1 Replies
I have a 1999 F250 Super Duty 5.4L, 118,000miles...engine seems to idle somewhat rough but tach doesn't seem to move off 1000rpm & when giving slight acceleration seems to act like its missing, shaking . But under acceleration moderate or high purrs like a kitten! Always starts good , few cranks. Any hints on the what issue might be?
View 2 Replies
I will occasionally get a misfire after a rain storm, lasts about ten minutes then goes away. there is also a slight miss (no CEL) at idle, that occurs all the time. I'm thinking spark plug wires.... the plugs were done last year, but nothing else. to my knowledge the wires and coil packs are all original. i'm at about 114K on a 2004 santa fe 3.5l.
Also, does the computer store misfire codes? I know I got them in the past and i checked it at the time, but didn't write down what cylinder it was. think it'll still be in memory?
Think it's ok to change just the wires and not the coil packs? kind of on a budget...
View 15 Replies
I am having great difficulty trying to figure out why my truck is surging so bad in park or in gear at idle. I have to mat the brake while in drive to prevent me from ramming the car in front of me. It all started when I replaced the air filter. Everything I've read leads me to the EGR valve, but that has been bypassed.
View 14 Replies
I have 2002 5.4L f150 120k miles. Bought it almost 2 years ago and did not notice this vibration at the time but it could have been there and I didn't realize it. The trans was replaced by ford with a reman at 90k. I'd assume they inspected the trans mounts but who knows.
At idle only, there is a vibration. Enough that I can see water in a bottle moving and a plastic bag shake., felt through the seat, hand on engine can feel it, can feel it through the door..etc. Very annoying. At 700-750 rpm it goes away. Happens in all gears. I don't want to shotgun approach this. What I've done: Replaced plugs and coils since it needed them anyway. They looked good! No difference. I've sprayed the maf down and cleaned the throttle plate (I know your not supposed to but some 16 year old will try to tell me it cured his idle and he gained 10 mpg, so I figured I would mention it). I've removed the IAC and cleaned it, plunger moves freely. My idle does not fluctuate. I have watched mode $6, it's not a misfire. I have removed the pcv hose and checked for cracks - it's in good shape. Replaced the pcv since it's cheap. Ran Chevron tehcron through it. Checked codes - nothing. I have an edge and it happens on all tunes as well as stock.
I have ability to read live data but do not know enough to interpret it, so that is about useless unless you can provide me acceptible ranges.
View 8 Replies
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
View 14 Replies
I bought a 2002 f150 4x4 with a 4.6l. It has 250k miles on it. a couple days ago. It had no problems at all during the test drive or for the 150 miles home. Yesterday after it warmed up, the oil pressure dropped to 0 while at a red light and had a rattling noise. Not a knock but more of a rattle. I can't isolate where the rattle is coming from. Oil pressure comes back with just the slightest of increase Of RPM and seems To have plenty of power while driving. I had read to check the pressure manually but with the noise I sense there truly is a problem. the oil appears clear and is full. What I should be checking on this.
View 1 Replies
My 2002 F150 (50,000 miles) 4.2 is surging when cold. I just got done replacing the pcv valve. I noticed it was running better so I cleared the service engine light, but now is surging when the engine is cold. I live in FL so it does not get that cold like up north. The following codes were the ones that the pcu put out, P1131, P1115, P0174 and P0171. I am leaning towards changing the IAC valve and maybe the oxygen sensors.
View 5 Replies
So I recently acquired a 2002 F-150 4x4 super crew with the 5.4 V-8. It idles rough (surging from 400 - 700 rpm) when cold, and sometimes dies, but more often then not it stays running. It runs and drives fine when the accelerator is pressed and when going down the road. When it gets up to operating temperature, and has been there for a while, it seems to idle fine 95% of the time. The codes I have are P0136 (bad circuit to O2 sensor), P1151 (HO2S detects lean mixture or something like that), and the infamous P0171 and P0174, which is lean exhaust/mixture on both banks. Now I have read extensively on the internet about these symptoms and have done the following:
Sprayed every vacuum hose with carb cleaner, and even around the intake manifold and injectors.
Considered the IAC (its new, the guy I bought it from replaced it a couple months ago) Torque app for android phone says vacuum is good. Cleaned the MAF and air temp. sensor with electrical cleaner Checked all of the vacuum hoses on the engine by pulling them off
Put grease around the fitting where the PVC valve attaches to the valve cover. Seemed to make it idle a lot better after messing with it, but I don't know if it was a result of the engine being fully warmed up, or my messing with the PVC.
What to try next? I'm close to just dissecting the top part of this engine and seeing what the intake manifold gasket looks like..or could it really be an 02 sensor?
View 3 Replies
I have a 2002 4.6L FX4. When I run the A/C for an extended period (say 15-20+ minutes), it will start to cough and sputter and eventually just die. It will restart but run rough and cough, sputter, die.
If I turn off A/C and let it set a while, it runs fine. No check engine light. Possible EGR problem????
View 3 Replies
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 Replies
I have a 2002 f150 with the 5.4. Its got a rough idle and a bit hesitant on acceleration. Im wanting to replace the coils and plugs but what brand of coils should I use?
View 3 Replies
I have a problem with a 2002 Mercury sable. At idle and under acceleration, it has a miss, it's worse when cold then improves when it's warm but never goes away and almost seems to come and go when driving. It's definitely worse going slow or idling. The check engine light is also on, I scanned the codes and it came up with 4 cylinders misfiring. codes were p0301 p0302 p0303 p0305 p0316 to be specific. I changed the spark plugs last weekend, how it ran at all is something I'll never understand they were so bad, obviously original with 150,000 miles on the engine.
It's a little better now but not much. Where I should look next? I've been told a lot of things but I can't keep throwing money at this, I'm unemployed so really the next major attempt is probably the last. Anything I should try? If it was carbureted with the old distributor I'd have this fixed in no time but fuel injection and computers, coil packs, all totally new to me. No white smoke out the exhaust, no funny noises just a miss and check engine light with only the codes above.
View 12 Replies
So today, I planned on switching the belt, idler pulley and tensioner since at least two of them are making noises. After taking all of the stuff off, belt, idler pulley and tensioner... and since I always compare parts I buy to parts that were in, making sure they are identical and I didn't order the wrong one. So first up I checked my tensioner and the position of them or angles are different, completely different.
So Google it to view a few diagrams and bang! it hits me... the one I took out from my F150 is for a non-AC... so back into the truck and I'm looking. Didn't have to go far when I realized that my AC compressor is missing!!!!
I keep looking around and I see that yes, I did have AC in it before I got it; because the guts are there but sliced! Great, so the job went from easy and easy I mean buy compressor and install; but now since the guts were cut, the PO sliced the thing out simply put.
1.) What are the bolt sizes that hold the compressor in place?
2.) Is there a wire connector on the compressor? or no?
View 1 Replies
I have a99 5.4 and its missing slightly when cold mostly. I'm thinking egr poss did tune up 7 mos ago so I don't think it's plugs or coil pacs seems to get better when it warms up...
View 11 Replies
