Ford F-150 - 1997-2003 :: 2002 - Slight Grinding Clatter In First And Reverse Gears
Jan 12, 2015
My friends truck is having a problem, and I haven't found any info on the specific issue. when you shift from P to D and accelerate, there's a slight grinding clatter in the tranny i think, bump it to 2 and the noise is completely gone! pull it to 1, and there she is again, also in reverse it does this, speed is not a factor, only the specific gears. i had read a thread which mentioned a "sun gear", and also that 1st and R are on the same bands?
I believe it was for a manual tranny that I had read about, but what this could be?! he's got a slight drag on the rear brakes, i assume it's his E-brake, could that have caused a transmission failure? We've removed the driveshaft and checked u-joints and all, nothing there, but when the truck reverses on the ground, you can watch the driveshaft bounce like it's binding. We grease the slip joint while we had it off, and we were able to spin the rear wheels by turning driveshaft w no problem while off the ground.
View 1 Replies
Advertisement
I've got a 2003 f150 with the 5.4 and 128,000 miles with an engine tick. Its not an exhaust leak I know that for sure. It has came up in the last 20,000 miles. I've used motorcraft 5 20 w/ motorcraft filter. I've tried a kreen engine treatment with no change. Heres the description/syptoms:
-Slight clatter for 2-3 seconds upon cold startup (happens very rarely)
-top end ticking that is loudest and most noticable when warm (quieter when motors cold)
-not timing chains/tensioners etc because the noise is coming from the top end and most noticeable on the passenger side.
-at idle the tick is present-when you rev at idle, the noise goes away.
-Driving (or having the engine under any load for that matter) the noise gets louder.
-Anytime I accelerate, tow/haul, go up an incline the noise gets worse
-Sounds like a "whirring" sound from within the dash.
With all that said I am thinking the lash adjusters are getting noisy. I had a certified gm tech that has 40 yrs mechanic experience under his belt and builds prostreet muscle cars on the side look at it. He listened to it to it and that was his diagnosis as well as its not that bad so just live with it. The noise at idle doesn't bother me, its when im driving with the windows down. The noise drives me crazy and is a little annoying to me.
Heres a link to a video of the sound and keep in mind it is much louder now : Triton engine noise/tick - YouTube
View 6 Replies
I have a 2001 f 350 7.3 diesel r 400 tranny 320000 miles. . Im having transmission issues. It makes a slight whine/ grinding noise only in first And reverse. And it surges. Sometimes its fine though to. Check engine light came on. Only codes i get are #4 glow plug out and a low boost pressure. Checked boost before fixin Running fine at the normal about 20 psi. ive read a bad or dirty map or iat sensor can cause transmission issues along with the low boost error code. But in my experience and some reading it sounds like a stall converter.
View 9 Replies
The trany is less than a year old rebuilt by a local shop.
Starting two days ago when i put the shifer in anything but reverse and 2nd it acts like it is in nurtral. 2nd and reverse are strong and do not slip. do you think its in the linkage? Or is my tranny dead?
its a 99 f250 256K auto 4x4 xl
View 2 Replies
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 Replies
The passenger side power window sounds a little rough, almost like a slight grinding and it raises and lowers slower than the driver side.
This is kind of what happened when the plastic gears crumbled on the passenger side of my ranger. Does this sound like bad gears or could it be something that needs grease?
View 2 Replies
I have 2002 f150, fx4, ext cab, 110000miles 5.4 automatic truck, i just replaced my spark plugs, it still have a little miss, thought spark plugs will resolve but its the same, im wondering if i should change O2 sensors? clean EGR Valve? IAC valve? i am not getting good gas mileage and maybe its this missfire or something, its runs good without any problems, just this slight miss makes me think if its the cause to bad MPG.
I tried to find threads with pictures of how to change O2, how to clean EGR, and IAC, i remember seeing these threads but cant find em. And you think these three things will resolve my MPG and the slight miss?
View 14 Replies
Noticed my 2002 F150 had a very slight vibration in the seat / steering wheel when cruising down the highway at 60 MPH.. Very slight, but was not there 2 weeks ago.. It seem to get a little worst as the 2 weeks progressed. Got all 4 tires balanced and rotated... no luck...Took both rear wheels off-- no problems with tires -- checked bearing clearance-- pushed and twisted on driveshaft yolk to check pinion bearing... nothing found......... last resort was drop back end of driveshaft and check U-joint.. It was tight and dry. Put drive shaft in 12 ton press and pushed out the u-joint bearings. Very dry and joint pins were starting to spall....... I mention this because I had checked " clearance" and "slop" and had "no noise" before removal... Truck has 139K miles on original u-joints .......... Something to keep in mind. Eventually it would have worn to the point that it was obvious, but in the first stages of failure, you just get small symptoms.
View 7 Replies
I have a 2002 f150 5.4 with 3.55 limited slip... For months now every time I hit a bump with the front right side there is a loud bang (sounds like a wore out bushing), and if I am driving slow at an idle you can here a thump every time the wheel goes around. And when I turn all the way it sounds more like a grinding sound.... The noise is getting very bad, what it is. I am very mechanically inclined but cannot figure it out.
Everything in the front end seem tight. When I lay under it if I get someone to spin te wheel the thump sound sounds like its in the front dif, kinda echoes through the front drive shaft but u joints seem good. I really think it's in the dif, and I'm hoping the banging noise I hear when I hit bumps is the same problem as the noise when the wheels go around....
View 3 Replies
I have a 2002 f150 with the 5.4 motor and a auto transmission and when I go in reverse the rear end makes a loud whining noise? The fluid level is fine. Should I add the gear oil additive to the rear end or change the rear end oil and add that? I am looking to sell the truck so what could cause this noise?
View 1 Replies
Anything else that could cause reverse to go out of an automatic tranny other than the tranny being shot? I don't know of anything but any way to keep me from replacing a tranny.
View 2 Replies
So my aunt has a 2002 ford f150 king ranch 5.4l and a night ago it started this problem which when you put it in drive which she has to put it in 2nd for it when she pushs on the pedal it will rev up to 2500rpms than jerks and goes and its usely fine till she stops than goes and it does it again...
Than today it wouldn't even go in anything but reverse... So than we herd about the Range Sensor on the side of the transmission and it seems like it was it so I unplug it when it was running and when i push on the pedal and it revs up to 2500rpms it will go forward and have power. So we went to get a new range sensor after like 4 hours trying to get the dam thing off and another 2 to get it back on.. I started it up and only reverse works again... So I unplug the harness to it again and we got the gears but 1st and 2nd will just rev and go.
We at a lost right now i even tighten the shift screws under the dash cause our expedition was loose at one time and the gear shifter was loose like hers. But even tighten the bolts it still don't fix the looseness or even the gears.. Is this a transmission problem? OR even the torq covertor?
View 4 Replies
2002 f150 fx4 ... I changed both front cv shafts cause they were making noise and the u joints and I still have a clicking noise in reverse if I turn my wheel at all to the right ...
View 1 Replies
I have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 Replies
My 2003 Aviator kind of stutters when in auto between gears. Most prevalent from 3 to D when driving regular. If I shift manually and tach it to 4k there is no stutter/vibration. My engine light is on and pretty sure the catalytic converter need to be changed. All new NKG plugs and associated coils. Throttle body clean, 91+ fuel only. Could this me a tranny starting to fail or computer/senor related? No other codes than the bank-2 O2 sensor....
View 2 Replies
No codes, transmission makes a slight grinding noise when putting it into reverse only. Has a slight bump from 1st to 2nd. I flushed 16 quarts of the sp3 through it. Been researching and see a lot of talk about the output and input sensors. Not my car but my sisters. Needs axles, timing belt water pump, ps return hose, plus have champions in there and old ass hyundai wires.... thing does idle rough, motor mounts are new.
View 1 Replies
(2000 F-350, 7.3L, 205k miles) Over this weekend, I noticed while driving mostly in the lower gears, that there was a slight hesitation with the throttle pedal depressed about half way or less. Seem to get worse as the day went by, but no lights or anything came on. Changed the fuel filter and added a fuel injection cleaner to the tank. Checked the oil and it was low, so I filled it to the correct amount.
Drove it around the next day, and it seemed to be good, until it warmed up some, and continued to hesitate. The hesitation seems as if it's not getting constant fuel, and the truck jerks a little. Once you get up to over 2000 rpms, it goes away. Looking up other reviews on similar issues, most have pointed to the throttle pedal sensor and just changed out the pedal assembly. Before I take it that far, I wanted to see what was the corrective action.
View 3 Replies
My 2002 Standard Kia Spectra. My car had been sitting and undriven for 6 months, after charging the battery and starting the car, I am having trouble shifting to gear. I was able to shift into reverse, with lots of grinding, but getting into 1st gear, I had to shut off the car and shift into gear, then start the car. I test drove around the block and I was able to get it into a few gears, but really had to press on the clutch hard. Although, when I stopped and tried 1st again, i had to shut off the engine to shift.
View 5 Replies
2003 Nissan Xterra 2.4. It grinds when I shift gears, gears through 2nd thru 5th.
View 8 Replies
When I have the clutch depressed and start to let out as I'm either in reverse or in first gear it makes a clatter/chatter noise. It also occurs when I have the clutch depressed and just rev the engine and it's in neutral. Some days it's louder than others. It doesn't matter if the engine is cool or at normal temp.
View 7 Replies
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
View 10 Replies
