Ford F-150 - 1997-2003 :: 2002 - No Cruise Control / Fluid Coming Out Of Brake Control Switch
Nov 13, 2013
I have an 02 f150 5.4 and since I got it it hasn't had cruse control. I went to a local ford dealership and they ran the vin and didn't find any recall on it. Under the hood on the master cylinder there is brake fluid coming out of the brake control switch. Would I have to do something with the harness too?
View 9 Replies
Advertisement
OK, so a friend's F150 just went up in flames in his driveway and he told me that the problem was the hot link behind a plastic/ rubber barrier at the main brake cylinder. I had a recall notice on my old truck but since I left the US and took the truck I never paid much attention to it, thinking typical overkill. Now I already heard from another buddy who caught lit brake fluid dripping onto the front tire and got the fire out before it spread and looked up the info today. Looks like our trucks are affected. Best to unplug the harness that goes into the brake master cylinder will prevent this problem from occurring? I never use cruise where I am, the roads are too small and slow.
View 6 Replies
How do I get the ac control switch out of the dash? Something must have come loose as I only get cold air or heat to the windshield...
View 13 Replies
I have an '02 F150 Lariat CC 5.4L. The truck is new to me and neither the cruise control nor the horn works. i have checked all (known) fuses and relays. I have tried the cc diagnostic, and the dash light DOES NOT illuminate. Should I assume that the dash light is not burned out? Is there a way to test the clock spring connections for continuity? and how do I access the connection
i checked the cc brake pressure switch and have continuity there.
View 2 Replies
I am having trouble with all sorts of functions on my 2002 F150 4x4, 4wd not working, cluster module illumination not working, horn not working, reving up and down at idle and sometimes dyin, cruise control quit working. I have been reading it is the GEM module that causes these issues. My question is I ordered a new one from Ford, when it arrives I was told I can just install it and It should be pre programmed. but one ford house tells me that they have to install it and program it. Which it right? I have seen several sites on u tube where people replace the module and then start their truck right up without any issue.
View 2 Replies
The cruise switch on my brake master cylinder is bad and causing the cruise to not work. I have it bypassed with a jumper wire and it works fine. is there any reason not to do this?
View 11 Replies
I just discovered my cruise won't "SET" (light goes out after 1/2 second) anymore after having the brake light switch done yesterday.
View 2 Replies
The "Cruise Main" switch on my 2003 Honda Accord will not stay engaged. When I push it, the Cuise Main lights up in the dash board and I can operate cruise control, but when I release the Cruise Main switch it doesn't stay on. I've tried electrical tape to hold the switch in (holds for limited time), and am thinking about bypassing the switch altogether. I don't mind if the Cruise Main is on all the time. I know I could replace the switch, but am looking for a zero cost solution.
View 1 Replies
My college son's 2014 Charger V6 has developed three issues since he purchased it used in late May. The cruise control has stopped working and the anti lock brake and traction control lights are constantly on. Any possible cause?
View 15 Replies
My 2010 Subaru Outback recently surprised the hell out of me by simultaneously turning on the brake warning light, the traction control light, the check engine light and (just for a bonus!) disabled my cruise control while flashing the cruise control light. I pulled over, quickly surmising that all of those systems could not have failed at 70 MPH without instantaneous death to either me or the vehicle. Both apparently still being alive, I tried turning the car on an off to reset the lights. No go. Subaru was not going to miss this chance to get me to the dealership! (who I had avoided to this point!) As I was far away from home and the car being very healthy, it seemed, I decided to drive on. I proceeded to put a couple of hundred more miles on the car before I got back to town.
My car had 39,000 miles on it, 3,000 miles beyond the warranty end. I learned that I have an error code of P0171, "Fuel Trim Malfunction (Air/Fuel too lean)". So I guess I'm wondering about a few things...why would this sensor set off every light on my dashboard and disable my cruise control? Seems a bit overblown for running a bit lean. My gut tells me Subaru has a sensor/software problem they are not owning up to. I'm a big fan of conspiracy theories and this really smells like one...
Second, jeez, I'm only 3K miles over warranty, don't you think they'd cut me some slack. I mean I love my Subaru, or did anyway, until this happened. Now it's just another POS car that breaks for no apparent reason...
View 10 Replies
Ok replaced the front brakes, tie rod ends, and all ball joints today. Also flushed old brake fluid and replaced with new. Now my cruise control does not work. Light on the dash momentarily flashes when I try to set the speed. I have checked all the fuses and the connections and everything appears normal.
2001 Ford F150 5.4L 4x4 off road pkg stock height and tire size.
View 7 Replies
2000 F 150, 4.2 v6, M5OD-2 Manual Transmission, LX, reg cab .. Cruise Control passed all static and dynamic self test. All fuses inside and under hood checked good and still cruse control will not engage. All other functions work: brake lights, turn signals, etc. Green cruise light is operational, checked pin #10 on wiring harness at servo,amplifier unit under hood and have good ground. The Cruise ON button will not turn on cruise control system and will not light green cruse light.
View 4 Replies
Got an 01 f150 excab with the 5.4 as of lately sometimes when i turn the 1-4 blower control know it wont do anything on heat or ac than other times it will work like it supposes to?
View 2 Replies
A few years ago I had the clutch changed on my 1997 F150. Afterwards the cruise control wasn't working. When I brought the truck back to the repair shop I heard the manager tell the mechanic to "attach the clip by the pedal" and that fixed it.
I just had some work done, had to replace the oil pan, and the mechanic had to remove the transmission. Now the cruise control doesn't work. I changed the Pressure switch but it didn't fix the cruise control. What that clip might be that fixed the cruise control last time?
View 3 Replies
I did the diagnosis,on my non working cruise control on my 2000 f250. The cruise light came on when, I, depressed the off switch and turned key on. I depressed on switch,cruise light came on.
I then depressed the resume, coast, and set switch, as described in the diagnostic procedure,suggested,and no light came on. Do the switches for the cruise control are bad.
I have checked the fuses at the power distribution box under the hood and checked the fuses under dash,all are fine. I just replaced the switch at master cylinder, as it was leaking and it had the recall switch replacement, too.
View 8 Replies
I need to replace, its either a brake pressure sensor or speed control deactivation switch . Would like to know which it is and can I get a generic one from other auto parts beside a ford dealer Can post a pic of part as soon as I figure out how to do that exactly. 2002 f250 super duty....
View 8 Replies
All, i have an issue ( or at least i think its an issue) with my 99 f150 5.4. When i use my cruise control, i notice when i put on the brakes slightly to slow down, it feels like its not coasting because you can feel the engine still engaged and wont coast. I think this happens even without the cruise on. What this could be? I have the latest update on the cruise control harness. I believe that was for power always to it even in off, causing fires.
View 3 Replies
I am stymied by a weird Cruise Control problem on a 2001 F150 Lariat SuperCrew with 5.4L V8 engine that I just purchased. Long story short, the cruise control does not work. That is, when I push the "On" button at any time while the engine is running (even when traveling at highway speed), the dashboard CRUISE light does not come on.
I ran the cruise control "self check" procedure. The first time I ran it, we failed with 3 flashes. So I checked the cutout switch on the brake master cylinder, and it was indeed leaking brake fluid. So I purchased a new switch and cable (Motorcraft SW-6350 Speed Sensor Switch Repair Kit) and installed them.
With the new cutout switch, we seem to pass the self test. That is, after pressing all the buttons in order , I see all the quick flashes of the CRUISE light
(1. On (flash), 2. Resume (flash) 3. Coast (flash), 4. Set/ accel (flash)). Then the accelerator pedal is pulled away from my foot.
However, unfortunately, the cruise control still does not work. That is, when I push the "On' button at any time while the engine is running (even when traveling at highway speed), the dashboard CRUISE light does not come on. What to look at next? I note that horn works, in case that's useful info.
View 14 Replies
I have a Ford F150, 2003. I replaced the switch above the master brake cylinder just a few months ago soon after I bought the truck. I put 17" rims and new tires on my truck and now my cruise control works intermittently. It worked fine before then.
Can there be a connection between the intermittent failure of the Cruise and the larger rims and tires? I know my speedometer is off by about 4 MPH at 55 but I expected that.
View 4 Replies
2001 F-150. I've got a leak around the warning switch and can't seem to find info about replacement. Is the switch and switch retainer screwed into the reservoir or is the outer ring screwed into reservoir and more of a compression type fitting that holds switch in place? Also, after removing and repairing will bleeding be necessary? Looks like everything I'm taking apart is above fluid level after I siphon enough fluid from reservoir to replace fitting.
View 2 Replies
99 f150 xlt power windows. My friends always like to roll my windows down to try and smoke cigarettes. I was wondering if there is any way to install a window lock maybe a switch that turns on or off but still allows me to control the windows from the drivers side.
View 2 Replies