I have a 2002 f150 4.6L triton. I've been having problems with it making a clicking noise. It only does it when its in gear. I put it in park or natural I hear nothing. But as soon as I put it in drive or reverse and put a little pressure on throttle it starts to tick pretty loudly.
View 4 Replies2002 f150 fx4 ... I changed both front cv shafts cause they were making noise and the u joints and I still have a clicking noise in reverse if I turn my wheel at all to the right ...
View 1 RepliesSo my aunt has a 2002 ford f150 king ranch 5.4l and a night ago it started this problem which when you put it in drive which she has to put it in 2nd for it when she pushs on the pedal it will rev up to 2500rpms than jerks and goes and its usely fine till she stops than goes and it does it again...
Than today it wouldn't even go in anything but reverse... So than we herd about the Range Sensor on the side of the transmission and it seems like it was it so I unplug it when it was running and when i push on the pedal and it revs up to 2500rpms it will go forward and have power. So we went to get a new range sensor after like 4 hours trying to get the dam thing off and another 2 to get it back on.. I started it up and only reverse works again... So I unplug the harness to it again and we got the gears but 1st and 2nd will just rev and go.
We at a lost right now i even tighten the shift screws under the dash cause our expedition was loose at one time and the gear shifter was loose like hers. But even tighten the bolts it still don't fix the looseness or even the gears.. Is this a transmission problem? OR even the torq covertor?
On my 2003 f150 4 by 4 I've been hearing clicking noises. When i take off from the start it starts clicking then gets faster up until I hit about 30 mph then goes away. The sound is coming from the back. Whenever I goes in reverse it rattles a little bit too (not so much of the clicking). Do I have a bad u joint somewhere back there?
View 1 RepliesI have a 2002 f150 with the 5.4 motor and a auto transmission and when I go in reverse the rear end makes a loud whining noise? The fluid level is fine. Should I add the gear oil additive to the rear end or change the rear end oil and add that? I am looking to sell the truck so what could cause this noise?
View 1 RepliesI always thought the clicking sound I was hearing in the morning was coming from the engine. Then I realized the sound doesn't start until the car is in gear, either reverse or drive. After a few minutes it will go away but until it does, it is a noticeable sound. I still have a warranty. I am wondering what this could be.
View 3 RepliesI have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 RepliesI just started hearing a loud click when I change from park to reverse and from reverse to drive. If I keep moving the knob between those three spots with my foot on the brake and hand brake off, I hear a loud click at each spot. Hard to describe... anyway, this only happens when I first start the car, by the time I get to work if I try doing that when I park there is no loud click sound. The thing is, I don't know if this was always happening and I just noticed it now, or if it just started.
View 14 RepliesI have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 Replies2002 f150 7700 with 5.4 triton and 4r100 tranny started chugging under acceleration and now stalls when put in D, 2 or 1. park and neutral are fine and reverse works perfectly.
Now when I put it in drive it chugs and stalls immediately... 1/10 times it will keep running but chug violently like its running out of gas. will get worse and stall if you press the gas. i can light the tires up for a block in reverse however.
Changed coils 1 2 and 3, IAC, bank 1 knock sensor, camshaft position sensor
I have a 1997 ford f150 5.4 litre truck and the truck runs real rough kinda surging in park and in drive and reverse i have a couple oxygen sensor codes P 0171, P0174, P0136, P1131, P1151 and an idle air control valve code P1506...
View 5 RepliesI was driving my 1998 Ford F150 the other day and pulled into a driveway. At that time, the transmission quit pulling like I put it in neutral. It shifts from park and goes into reverse but not drive. It has the 4.6L and is 2 wheel drive.
View 4 RepliesI have a 2001 f150 crew cab 4x2 82k miles 4.6 with a 4r70w. Was pulling it over a curb and it popped now it will shift into reverse and load the motor like its pulling against a wall. In drive it will move some but still will lock up and stop moving. I assumed something in the rear had broken from the way it would roll a few feet and lock. Replaced the rear and still have same problem. Is there something I can replace to fix a stuck park or does the transmission need replaced or rebuilt?
View 1 RepliesIn my 1998 f150 4.6L 5 speed manual. When I go to put it in reverse I get 1st instead, but if I do a second shift to reverse I get reverse. This happens on an average of once a week.
I know this can happen in FWD cars where you put it in one gear and get a different gear instead. Something to do with the shifting cable. But the f150 is RWD, the shifting problem only happens in reverse. Is this problem someone without ASE certificates can do, or without dropping the transmission?
I'll add to this so I don't start yet another post. Ive thought of the problem and if it was really going into 1st instead of reverse the problem likely would be bad enough it would just stay in 1st. Its possible that I am getting 4th gear when I go into reverse which tells me the clutch grabs really well, and its a problem I really need to fix, I don't know that much about transmissions but I do know if it keeps getting 4th instead of reverse, the clutch wont be so good pretty fast.
My 2002 Subaru Forester is making this weird clicking noise and unlocking as I drive. It seems to get worse at night, and especially when turning left, or braking. My mechanic can't figure it out.
View 10 RepliesI have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
I noticed recently that my car started this popping noise when braking in reverse gear. I never ran over anything and babied it for all the 6000 miles it has on the ODO. 2015 Camry
View 4 RepliesI have a 1997 F-150, 2 wheel drive, 4.6L truck. Recently the transmission got to where it didn't shift properly. Then it got to where, after driving it about 10 to 15 miles the transmission would drop out of gear with the transmission selector in drive.
I have replaced the transmission sensor, the rear end sensor and it still does the same thing. Drive about 10 to 15 miles and, with the transmission selector in drive the truck will not pull. The motor can be rev'ed but the truck won't move just like it was in neutral.
What is wrong. The transmission shifts fine, the truck runs fine, but after 10 to 15 miles the transmission quits working.
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
Today at a light my truck wouldn't upshift. I can manually shift from low to second but not to drive. Reververse works fine. I was noticing a slight slip between 45 & 55mph and would sometimes go away if I disingaged the overdrive.
View 2 RepliesAnything else that could cause reverse to go out of an automatic tranny other than the tranny being shot? I don't know of anything but any way to keep me from replacing a tranny.
View 2 Replies