Ford F-150 - 1997-2003 :: 2002 - Brake Pedal Goes Half Way To Floor?
Jan 16, 2016
2002 F-150 4x4 w/ 5.4 v-8. Brake pedal goes half way to floor before it starts to stop the vehicle. I have replaced and bled the master cylinder, bled out all of the calipers, and the calipers are installed correctly because the bleeder screws are at the top on all of them so no air can be trapped up there. The truck seems to stop fine, but just takes more pedal to get it to start stopping than I'm comfortable with. Could the ABS unit need bled out too? Or could it be an adjustment issue with the booster rod?
Also, something else I noticed, and it may be related..the ABS unit usually makes a slight clanking sound (like someone kicking a metal garbage can) a couple seconds after the key is turned on. I know its the ABS unit because a couple weeks ago I had a friends scanner hooked up to the truck, and I went into the ABS computer to clear the codes (have ABS light on from what I found to be a bad sensor wire on the front drivers side according to the scanner) and as soon as i cleared the codes on the ABS, it made that sound. I don't know if maybe there is something wrong with the ABS actuator, or if it's related to the brake pedal issue.
View 3 Replies
Advertisement
Last week my brake pedal started going to the floor when I stopped, it still stopped and felt fine on the top half of the pedal travel but then it would just slowly fade to the floor. I took it to a local shop and they said the master cylinder was leaking internally and my rear brakes were shot. I have 75,000 miles and the rear brakes were original so I told them to fix it. This is basically what I expected it to be.
They kept thinking they were getting defective master cylinders but after the two Napa parts and two Carquest parts they realized they misdiagnosed it and said I needed to take it to the dealership. I paid for the rear brake job since it needed done anyways and have an appointment for next week at the dealership. What might be causing the problem? I see no brake fluid leaks, no vacuum leaks, the booster was replaced 25,000 miles ago due to noise, no ABS light on, no CEL on, no other symptoms.
View 14 Replies
I have a 2003 F-150 supercrew 4x4, was having problems with the brake pedal going to the floor, had replaced the front calipers, master cylinder and the brake booster. I have blead everything out including the rear calipers even though I didn`t touch them, the truck stops but the pedal isn't what it used to be, even when the truck is off the pedal has a tendency to go down, there is nothing leaking and not losing fluid, don`t know what else to do?
View 3 Replies
The brake pedal intermittently goes to the floor on my nephew's 2003 F150 without grabbing at all. Pumping the brakes restores them, then they act normally for a while. I've replaced the master cylinder with a new Motorcraft unit, no change. No ABS codes. All rubber lines are in good shape. I'm stumped, although I suspect the ABS system somehow. I'm going to have him pull the ABS fuse and see if the problem goes away.
View 6 Replies
I have a 2000 SCrew KR F150. A couple of weeks ago I noticed the brake pedal was slowly going to the floor while at a red light. I pulled over and popped the hood checked the fluid reservoir. It was full, so obviously no wheel cylinder issues or fluid loss. I haven't had a chance to tear into it yet.
View 14 Replies
I did a search and found nothing. When I press on the brake pedal, it seems to go half way to the floor before grabbing. The other 2010 I tested did the same thing. Is this common or is this something that I need to take to the dealer?
View 5 Replies
The other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 Replies
I bought a 97 f150 4x4 last week. I was cleaning the frame up with a wire brush on a grinder and accidently cut one of the front brake lines. Seeing how this truck has only 100k on it and all oem stuff on it, I decided to replace the front brake components, calipers, pads, rubber and steel lines. Got it all back together and bleed the air out of the front brakes. But the pedal still goes to the floor. I can pump them up with the key off but when i turn it on the pedal goes to the floor. I did not bleed the back brakes becasue I assumed that the master cylinder would be divided and independent of each other- back and front. So it this just that the back brakes needs bled or do I have another issue like bad booster- everything was working well before I cut the line?
View 6 Replies
In the first instance of this problem, my brake pedal was stuck to the floor. By pumping it a few times, it gradually released and rose to the proper level. Brakes then seemed to work fine for a couple of weeks, until I reversed out of a parking space, but could not brake the car when I shifted into drive. I pushed the brake pedal to the floor, but could not stop until I ran over two large boulders that, stopped the car short of a big tree.
My mechanic doesn't know exactly what went wrong, but is replacing the brake cylinder. I fervently hope that fixes the problem! What could it be?
View 4 Replies
Working on a 2002 Hyundai Elantra GT. 4 disc, no ABS. Problem is the brake pedal goes to the floor without much force. I bled all 4 lines, but no improvement. Rigid lines from the brake master cylinder to the rear wheels were very corroded, so I ran new lines. The old ones pretty much fell apart when I took them off the car. I also replaced the brake master cylinder. I tried to bleed the brakes again, but couldn't get much (if any) fluid pressure at any of the wheels. Yes, I found a couple leaks at the junction points for the rigid lines, but I re-flanged those connections and got rid of all the leaks. Still no real pressure when trying to bleed.
So, I tried a second, then a third master cylinder with a new attached resevoir. No improvement. I bench bled the snot out of this third master cylinder because the symptoms clearly suggest air was likely trapped somewhere in the system. I used a wood dowel to fully actuate the cylinder many times after all the air had been released while I had short clear hoses running from the master cylinder outlets into a little plastic cup filled with clean brake fluid. I wanted to make sure there was no way air could be in the MC, and no air drawn back in when I released the wood dowel.
Next, I quickly capped off the MC outlets and connected a hose to each brake line individually where they normally screw into the MC. I then let clear fluid drain through each line until it was spilling out clear of each caliper bleeder with no air bubbles. So, no lines are kinked, clogged, or contain air.
I took every precaution to keep air out of the system, yet when I push the brake pedal, there is still virtually no real pressure generated by the MC. The power booster rod is shoving the master cylinder in as it should. I don't think there's any problem with the power booster.
I've used gravity bleeding, manual "push & hold the brake pedal" bleeding, vacuum bleeding, and I'm certain there is no air in the lines or calipers. Still no significant pressure coming from the MC when I push & hold the brake pedal to the floor. It takes maybe 20-25 pounds of foot pressure, but always goes completely to the floor with all the bleeders closed. If the pedal is held to the floor, fluid slowly seeps from the bleeders. I'm used to it spraying when doing this on a healthy brake system.
View 16 Replies
I have a 99 F150, Regular cab, long bed, with a weird brake problem. With the engine off, the pedal goes firm about 3 inches. But when you start it, the pedal goes to the floor.
I've replaced the master cylinder, and bled the heck out of the 4 wheel cylinders. No soap. The pedal goes nearly to the floor, and does not "pump up".....but does stop the truck.
The ABS light is "on".
View 3 Replies
acts like abs sensors could be bad. but the brake pedal goes almost to the floor, after it does it's pulsating. But the abs light does not come on. I already changed brake booster, no change!
View 5 Replies
I have a 2002 Honda Civic EX 1.7L. Recently the brake pedal would sometimes go to the floor when I'd apply the brakes. The car would still stop, but not as quickly as normally. If I apply the brake and it goes to the floor I would release the pedal and reapply the brake and it would stop at it's normal position and the brakes felt firm and the car would stop fine. I was told my problem was the master cylinder so I bought one on Sunday and replaced it. I bled the lines and it seemed like all the air was out. The brakes worked great and the pedal stopped in the same place and was firm.
Now today on my way to work the pedal went down a little farther than normal during one stop. On the way home it stopped in different places. The brakes would always grab and the pedal felt fairly firm wherever it stopped. I drove it this evening again and the pedal went to the floor like with the old master cylinder. One pump and they grabbed in the normal spot. What is going on? Did I not bleed the lines well enough? Is the new master cylinder just junk? I saw in the manual that air can get trapped in the ABS sensor, but an air bubble problem should just make the pedal squishy, not change where it grabs, right? I'm stumped and I really don't want to take my car in if I can fix it.
View 6 Replies
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 Replies
4x4 wont work, when I shift the lever on the floor it doesn't engage so i bought two new solenoids.. didn't work, have power on both solenoid connections. If I unhook my vacuum lines from the solenoid, I can push the Actuator rod in making my 4x4 work. I've gone threw everything.. have vacuum, have power on my solenoids. Just nothing works when I shift into 4x4 on the floor.
View 3 Replies
I have an 02 f150 ext cab fx4 with just under 140,000 miles my first problem was when I shift from reverse to drive I have a loud clunk/bang I was trying to find out what was wrong so my brother in law was looking out the drive shaft he pushed it into the rear end now when I am over 65mph and take my foot off the gas I have a vibration but only when I take my foot off the gas and above 60-65mph the steering wheel or peddles don't vibrate but the floor does .
View 3 Replies
I just finished replacing pads, calipers, rotors, wheel cylinders & brake drum hardware on my truck along with flushing the brake fluid. The brakes work but the pedal goes almost to the floor. While bleeding them some air did come out as expected. But a couple times the master cylinder reservoir got very low on fluid. The workshop manual talks about bleeding the MC but are special fittings needed for that?
View 10 Replies
I have a 1998 F 150 extended cab and the brake pedal is low. The front calipers and rotors were replaced last year because the left front caliper froze on and smoked the pads. I also replaced the brake booster and master cylinder because the brake booster showed signs of leaking vacuum. The whole system has been bled completely twice. After each bleed, the pedal was high and firm.
I have not found any sign of leakage and the fluid level looks ok and unchanged. The rear brakes look ok, but no work on them in last few years. Mileage is 198k. I had to hit the brakes hard on a muddy road a few weeks ago and the truck stopped straight, so the ABS seems ok. The problem is that the pedal has dropped down a few inches from where it was then the system was bled out. What to check next?
View 4 Replies
I have a 99 f150 and it won't shift out of park. The taillights work and I tried to turn the key forward and move shifter to neutral but it didn't work. Is it the switch on the brake pedal or the interlock solenoid by the shifter?
View 12 Replies
I just joined as I bought my '97 F-150 5.4 4X4 about 3 months ago. The dealer gave me a 6 month warranty but hasn't honored it at all and I've had one problem after another. That's another story though but right now I'm just trying to fix the important issues. The problem at hand are my brakes.
I was noticing a couple days ago (maybe I never noticed it that much as it was a new vehicle to me) that when I apply the brakes it sounds like a bicycle pump and the pedal travels nearly all the way down. It doesn't hit the firewall but I'd probably guess it has 3 more inches or less until it bottoms out. The hissing only occurs as the pedal travels and stops when the brake pedal isn't moving.
Now I'm not sure if the hissing sound is normal as I replaced the brake booster (from the junkyard though) and the new one still hisses when I apply brakes. The brakes seem to work okay, could be more sensitive it's just the pedal feels soft until it almost bottoms out like I stated before and the the brakes grab a little bit harder. What could it be?
View 2 Replies
My dad is having problems with his truck, brake pedal goes all the way to the floor even after bleeding all the brakes and the master cylinder. The wheel cylinder didn't have clips in it and he fixed it and it hasnt changed. What do we do? Its a 1993 f150 4.9l.....
View 4 Replies
