4x4 wont work, when I shift the lever on the floor it doesn't engage so i bought two new solenoids.. didn't work, have power on both solenoid connections. If I unhook my vacuum lines from the solenoid, I can push the Actuator rod in making my 4x4 work. I've gone threw everything.. have vacuum, have power on my solenoids. Just nothing works when I shift into 4x4 on the floor.
View 3 RepliesSo I drive a 19 97 F150 v8 5.4 4x4 and while on the freeway I noticed that my overdrive button was blinking on the shift lever. The truck wasn't driving any different than usual, so Im just trying to figure out what this means.
View 1 RepliesI just bought a f150 2001 5.4L crew cab. It has the O/D switch in the gear shift lever and the black plastic handle is broke. I found a complete replacement lever on ebay but cannot find any tutorials on how to replace this.
View 8 Replies1997 F150 xlt 4x4 ... When I shift the gear shift lever to below D (2-1) it blows a fuse and I lose instruments. Replacing the fuse is not difficult, just tiresome..
View 6 RepliesThe Speed Needle works fine. But...the Odometer part quit some time ago. I can't tell what my fuel Mileage is now. How to troubleshoot this problem?
Things that might affect this problem; Transmission skids loudly when going in and out of 4-OD. It could be the Torque converter clutch?
The Gear shift lever is sloppy. Doesn't fill me with Confidence.
Brake fluid warning light is on most of the time. Fluid level is up hi though. Driver door mirror control switch don't work in one direction Who on this Forum has a Switch for me?
2002 F-150 4x4 w/ 5.4 v-8. Brake pedal goes half way to floor before it starts to stop the vehicle. I have replaced and bled the master cylinder, bled out all of the calipers, and the calipers are installed correctly because the bleeder screws are at the top on all of them so no air can be trapped up there. The truck seems to stop fine, but just takes more pedal to get it to start stopping than I'm comfortable with. Could the ABS unit need bled out too? Or could it be an adjustment issue with the booster rod?
Also, something else I noticed, and it may be related..the ABS unit usually makes a slight clanking sound (like someone kicking a metal garbage can) a couple seconds after the key is turned on. I know its the ABS unit because a couple weeks ago I had a friends scanner hooked up to the truck, and I went into the ABS computer to clear the codes (have ABS light on from what I found to be a bad sensor wire on the front drivers side according to the scanner) and as soon as i cleared the codes on the ABS, it made that sound. I don't know if maybe there is something wrong with the ABS actuator, or if it's related to the brake pedal issue.
Last week my brake pedal started going to the floor when I stopped, it still stopped and felt fine on the top half of the pedal travel but then it would just slowly fade to the floor. I took it to a local shop and they said the master cylinder was leaking internally and my rear brakes were shot. I have 75,000 miles and the rear brakes were original so I told them to fix it. This is basically what I expected it to be.
They kept thinking they were getting defective master cylinders but after the two Napa parts and two Carquest parts they realized they misdiagnosed it and said I needed to take it to the dealership. I paid for the rear brake job since it needed done anyways and have an appointment for next week at the dealership. What might be causing the problem? I see no brake fluid leaks, no vacuum leaks, the booster was replaced 25,000 miles ago due to noise, no ABS light on, no CEL on, no other symptoms.
I have an 02 f150 ext cab fx4 with just under 140,000 miles my first problem was when I shift from reverse to drive I have a loud clunk/bang I was trying to find out what was wrong so my brother in law was looking out the drive shaft he pushed it into the rear end now when I am over 65mph and take my foot off the gas I have a vibration but only when I take my foot off the gas and above 60-65mph the steering wheel or peddles don't vibrate but the floor does .
View 3 RepliesToday at a light my truck wouldn't upshift. I can manually shift from low to second but not to drive. Reververse works fine. I was noticing a slight slip between 45 & 55mph and would sometimes go away if I disingaged the overdrive.
View 2 RepliesMy 97 4.6 ran fine but the 4x4 light came on even when the transfer case lever was in 2wd. Then one day it would not start. It cranked over fine but would not fire. I added fuel but it didn't work. I pulled a spark plug lead and attached a spark plug while I jumped the solenoid and cranked over the engine to visually check for a spark as I have done on older trucks. Well it cranked a couple of times and then it died and won't even crank now, I must've fried something, the batterys fine. If there is a fuse or something? What could have happened when I jumped the solenoid?
View 4 RepliesJust need to know how common this brake adjusting lever is? Awhile back I rebuilt my whole brake system and for some unknown reason the DS rear drum brake wants to keep over adjusting. Checked and double checked everything but can't see what would be causing it.
The fix has been to pull the wheel and drum and back off the adjuster but that's getting old. If I had more time and enthusiasm, I'd switch the shoes and hardware side to side to see if the problem follows the hardware. My solution for now is go with manual adjustment and to disable the DS adjuster by cutting off the end of the lever.
Before I hack up a lever I'd like to have a back up in case there is any problem. Not sure if the junkyard will have what I'm looking for and don't see the correct style lever on Rockauto or at my local parts places. My luck is to cut up a part that's hard to find.
I accidentally broke the control lever where the cruize control attaches. I've looked all over but I can't find the lever. Where I could buy just the lever? New throttle body is more than I want to spend.
View 1 RepliesI intended to purchase a 1997 F150 4x4 today and found that the manual transfer case lever will not move at all. I have read the manual and it seems simple to move from 2H to 4H (at stop of up to 55mph). No movement in the lever at all. Owner said he never uses it and has no idea what is wrong.
View 9 RepliesI have a 03 4x4 5.4lt supcab with 154k miles. I replaced the shift motor about 40,000 ago but it has always been tempormental like I had to engage it in 4lo in N and then shift to 4hi to keep it in 4hi. Now fast forward to today. Went to shift to 4lo in N and it didn't shift. I only heard the relays click once and then it wouldn't shift into any gear even though the indicator was on PRND123. Didn't matter.
Also, Park didn't engage and the speedometer acted like it was engaged in RN and D. No movement what so ever. I think it might be the shift motor that shifted part way and is stuck in between gears. Is this possible? I drove fine to the dirt road and I haven't had problems other then the shift motor being touchy. I don't want to pay for a new tranny if it might be the shift motor.
I have a 2003 F150 5.4liter 4x4 and when it is cold I can not get the 4x4 to engage. It is a manual shift for the transfer case not electronic. It shifts but does not activate the 4x4 when it is cold. The 4x4 does work when the temp is about 30 degrees or better. Where to start?
View 1 RepliesI recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
I've got a problem with my 4x4 not engaging. I've been ready and re-reading all the related posts and threads and am still confused. Here goes. Early in the fall I had no problem shifting in or out of 4wd. Then when it got well below freezing up here, it stopped working. I had it in a warm shop and all of a sudden it worked fine. After sitting outside again it wouldn't work.
When it was warm, I had no problem shifting in and out of 4x4, dash lights functioning as normal. As it got colder it only seemed to work if I really pulled quite hard on the stick and the 4Low indicator didn't work but 4Low was obviously engaged. Now after another day or two outside, nothing happens at all. When the diff does engage, shifting out of 4x4 is never a problem.
Transfer case seems fine as the front drive shaft turns when I shift into 4H and drive forward. After researching a bit, I crawled under and pulled the blue line off the actuator and had someone shift into 4H, I couldn't feel any vacuum so figured it must be the engage solenoid especially since, shifting out of 4x4 is never a problem.
My question now is, shouldn't the lights on the dash be on even if the solenoid isn't working? I am now starting to wonder if its the sensor switch on the transfer case but I don't see how freezing should affect the switch and would think I'd have issues shifting out of 4x4 as well as in. If I put it in 4X4 and test for current at the solenoid and it is there, can I assume that the switch is fine and the problem is in fact the solenoid?
Ok, have a 2003 fx4 auto trans with manual 4x4 ...I notice more and more that say at intersections, when I start out either turning left or right it feels like the 4x4 is slightly trying to engage, or a chuttering feeling..best that I can describe it. any thoughts, I have 106 K and do need to change out the diffential oils etc.
View 9 RepliesI have a 98 f150 4wd with manual shift on floor (msof) and the 4wd will not engage. I've done research and I've learned quite a bit but still have an issue. In All the research I've done I have learned about
View 3 Replies1999 F-150 Sport 4x4
So the deal is I had to use a slim jim to open up my truck door the other day. Door still locks/unlocks fine, only not with the key. Key will still fit & turn the barrel without any prob. just doesn't engage the lock. Took the door panel off and it looks as if the Rod that connects the inside of the key barrel to the lower (part)? not familiar w/name. has come loose.
Looking for a diagram/picture of how it should look to get everything put back together so the key'll work again. Sucks unlocking passenger side and climbing over to open driver door.
Just tried to engage my 4x4 today to see if it was working and nothing. It is the electronic shift on the fly. I started checking the vacuum hoses and found one that looked like a mouse chewed threw part of it and repaired that line. Still no 4x4. So...there are no lights coming on, no sound from the transfer case shift motor and no noise of any kind when cycling the shift ....
I pulled the connection apart at the shift motor to test for voltage with 2hi and truck running and no 12volt. I tested all the pins but not sure if i did it correctly. Also the shift motor itself is rusty on the outside casing. What pin to test for voltage?