Ford F-150 - 1997-2003 :: 2001 - Jerks While Accelerating Above 40 Mph?
Nov 23, 2009
I have a 2001 F150XLT 4x4, V8 Triton engine with offroad package that just rolled over 119,000 miles that just started giving me problems 2 weeks ago. When I accelerate at speeds above 40 mph the truck surges or jerks ( the best way i can describe it ) sporadically unitil I get to cruising speed. If I'm cruising at say 70 mph and go to pass some one and accelerate it does it again. The transmission feels like it shifts smoothly thru all the gears and there is no whining sounds, transmission sounds normal. There is no check engine light, so I assume a diagnostic check might not show anything. Advice from guys at work say possible ignition module, coil pack, transfer case ??? It never feels like the truck wants to stall and it never feels sluggish when accelerating like there is a fuel problem.
View 14 Replies
Advertisement
Just purchased a 2001 Ford F150 super crew lariat v8 4.6/5.4 2v OAD at 156k miles, iv had no problems with it until I drove over the pass and after 2hours of driving my truck started to jerk when I accelerate between about 40-60mph. I don't experience any other problems over 60 it runs smoothly and in town under 40 it also runs smoothly, no check engine light. The next day is still continues to make a jerking motion, which feels like from the rear.
View 3 Replies
I have 2003 Buick Century. I started having problems with the car after coming to a stop, accelerating - the car starts to go hesitates, then jerks a bit to go. This does not happen every time after a stop but when it does the service engine soon light comes on. Initially I got the P0401 code (I think) and took it in to a mechanic. They could not find anything wrong with the car but did clean out the EGR valve, that didn't work, they worked on my transmission and replaced other parts, still no success.
I took the car to another mechanic who replaced the EGR valve and several other small parts. I still had the problem but this time the error code was P0420. I took it back again and replaced the spark plugs, O/2 sensor, catalytic converter. That hasn't fixed the problem. The mechanic said that they have taken my car for several test drives and the car has not demonstrated the problem. The error message still reads P0420 even after all of the parts have been replaced. The 2nd mechanic has washed his hands of my problem.
View 2 Replies
Truck is 08' with 5.4, 3.55 gears, auto trans. 84k miles. Recently purchased from the TSA fleet trucks, so I have no clue what PM procedures were done prior to me getting it.
I noticed the following: when I get the truck into OD and then slowly decelerate (meaning I let it coast and im not braking) to about 40mph then get on the gas (normal acceleration) the truck bucks hard almost like when your spinning wheels on snow or ice and put the truck in 4wd and the front rear locks. or a limited slip rear that catches when one wheel is spinning.
if I accelerate hard the truck pushes thru it and doesn't buck as bad. I have searched this out and there are several threads about it that describe just about exactly what im talking about, the following have been brought up as possible problems:
1) bad spark plug/s and or coil/s
this seems to be the most common answer to the possible problem.
2)broke valve spring
3) bad torque convertor
So at 84k miles im thinking replacing the spark plugs would be fine to do as a PM. So coils.............should I just go ahead and replace them as well? I found them (motorcraft). does that seem right?
As far as spark plugs, I have already read the horror stories on the 04-08's breaking the plug in the head. I have also read that before 10/07 was the trucks that had the issue. my build date is 02/08. am I good to go with normal removal of the plugs? the best method I have read for removing them is spray carb cleaner down the hole and let it soak overnight and then the next day drive the truck get it nice and hot and remove them right after you park it,,,,
View 14 Replies
We have an '03 Santa Fe (2.4L). We are the original owners.
About 18 months ago, one of our Ignition Coils cracked and caused a misfire when then engine was under load. I replaced the coil, wires, and plugs myself at that time.
Since that time, we have experienced intermittent engine jerking while at highway speeds. There does not seem to be any pattern, and it does not happen every time we drive it.
I took it to the dealer who diagnosed a valve cover leak. They replaced the gasket, one ignition coil, wires and plugs. The problem still happened intermittently after that. I brought it back to the dealer, who diagnosed a valve guide/seat leak. Oil is getting into the cylinder and fouling the plug they say.
I could not afford the fix (and was very dissatisfied by the service I received) so the dealer recommended to change the plugs every 3 - 5K miles to get me through. I was told this on 03/31/09 (125695 miles). I replaced the plugs, wires, and BOTH coils again at that time.
Last week @ 130K miles the engine jerked again. I replaced all four plugs again Sunday morning, but the ones that I pulled were NOT look oil fouled. I showed them to a mechanic friend and the guy at the auto parts store. Both agreed that the spark plugs looked almost new. Sunday evening, while driving on the freeway, the car jerked again!
Since this happened again SO soon after changing the plugs, I really have a hard time believing the valve guide diagnosis. Some possibilities I have seen/heard:
- Crank position sensor or camshaft sensor (This was replaced at 78K miles along with the all of the belts)
- Clogged fuel filter
- Bad O2 sensor
- Vacuum leak from the hose that is between the throttle body and the engine casing
- The dealer's valve seat suggestion
View 23 Replies
Below is a link to a video showing what my 2003 Hyundai Elantra is doing. It is idling very rough (Jerks at idle) and can actually be heard in the exhaust. I think it may be miss firing?? Does not do it at speeds over 60. Under 60 it can be felt at times, but only at low RPMs. [URL] ....
View 16 Replies
2003 hyundai santa fe 2.4l ... When driving on highway speeds of 65 miles hour, I take foot of the accelerator and I put it back on to gain speed , it starts jerking or bagging. Also in the city when I press accelerator seems to have no power. I have no codes or check engine light on, what could it be?
View 2 Replies
Ive got a 2000 4x4 F-150 with a 4.6 and a 4r70w. The transmission and transfercase were replaced by the P.O aprox 2,000 miles before i bought it..
i was driving it today, and while accelerating it missed a shift into 3rd, then nothing no forward or reverse, i sat and messed with the gears for a while then suddenly it shifted into 1st now it drives with a slight resistance, revs up to about 3K before shifting and shifts HARD up and down, and i cannot get over 40 mph its at about 2800 rpms and feels like im hitting a rev limiter wont shift again and wont accelerate anymore..
When at that speed I hit the OD off and it downshifts so i think i still have od?
View 8 Replies
2002 F-150 4.2L. About a year ago, it threw the P0171 and 0174 codes up. After replacing all the simple stuff, I bit the bullet and replaced the lower intake gasket as well as the upper intake gaskets. Buttoned it all up, reset the codes and we were back in business. No issues, truck ran good. About 6-8 months later, the check engine light came back on, I check it and it was that pesky set of codes again, 0171 and 0174.
It still ran fine, but the codes were there, so I just drove it for a while (it's a company truck that doesn't get driven that much).
A couple of weeks ago while driving it, it acted very sluggish. You could mash the accelerator and it would just very slowly run up the speed. It never hesitated or missed, it just got very very sluggish. Checked the codes, no additional codes.
Then it began to stumble when you mashed the gas.
I put new plugs (old one's looked great, other than a huge gap), new wires, new coil pack and started it. Pushed the gas pedal, it just dies.
I look for obvious vacuum leaks and replace a couple of elbows for the PCV and it seems to run a little better. Enough so that I can drive it, but still not running right.
I ordered all the intake gaskets and new isolator bolts and spend Saturday pulling that apart. I didn't do the lower intake because the upper intake gaskets looked so good, I just don't believe this is a intake gasket problem. None the less, I installed the new gaskets on the plenum and upper intake, new isolator bolts, replaced a couple pieces of vacuum hose that looked cracked, started it back up, it ran as smooth as silk.
Convinced I had it fixed, I went for a test drive. Idling, it is as smooth as you could ask for. Pull up to a stop sign, wait, step on the gas and it chokes. Just stumbles and you can hear it almost backfiring and pushing air back through the system.
I've put new PCV, new EGR, new vacuum lines in several places, new upper intake gaskets, new plenum gaskets, new isolator bolts, and even new o-rings on the injectors, and I'm still getting the 0171 and 0174 codes.
With the diagnostics on, I can see voltage varying on all O2 sensors, so I assume they are working (none of them are reading 0 volts). It doesn't throw any other code up, other than the 0171 and 0174.
At this point I feel like I'm replaced every single thing ever mentioned in any 0171 and 0174 thread on the internet. Where to go next? 1 more point, if you very slowly push the gas, it runs fine, but any pressure on it, it bogs down and just stumbles.
View 9 Replies
Recently, my truck has started rolling back from a stop when accelerating. There seems to be a hesitation between when I depress the throttle and the transmission engaging. It doesn't clunk, just delays. Been doing it for a few weeks, but is now getting worse. Today, the symptoms are similar but more pronounced. When driving there doesn't seem to be an issue, just moving out from a stop.
Checked the fluid idling in park, level was good, fluid looks great, was changed by a shop 6 months ago. Is my 319,000km trans on its way out?
View 14 Replies
My trucks been doing something weird. When accelerating around 45-55 mph, a couple seconds after it shifts to 3rd, it does a weird type off shake/shudder. Feels like I hit a small bump in the road. Also when coming out of a cruise to accelerate, it will Make a very violent clunk and then speed up. I'm thinking it's a problem with my torque converter but my mechanic says transmission and my buddy says rear end lol. I dropped the pan and there was some shavings but nothing huge and it was the first time it was ever dropped. After 90k miles.
View 14 Replies
So I have an issue with my 03 f150, Basically It clunks in various scenarios such as Accelerating also occurs take off and general breaking/slowing down but not really when stopping. December when it was cold and I was decelerating (not on the break just coasting) it feels like i was driving on the shoulder.
It does it much more in cold weather. Just had the truck out getting a little rough with it for 5 or so hours today and 0 issues with it.
I was thinking it was a slip yoke issue that I hear allot of trucks have the issue but I was at the dealership today and both guys and a mechanic sitting there were like "never had that issue on an 03 f150, might be your back end." They also stated the clunking would always occur and be more prominent when breaking which its not.
I am certain its not the transmission its not occurring with any shift point. Kind of hard to do it if its hard to reproduce in the heat.
View 9 Replies
Noticed the other day when I was driving on the highway my truck started humming when I was accelerating past 30. From a dead stop to 30 its fine, but after it starts humming. Its only when I have my foot on the pedal. When I let off, it stops. The sound is coming from the rear/under.
View 3 Replies
What can cause shutter in 1998 f-150 4.6 4x4 4r70w when slowly accelerating?
View 5 Replies
Its not the tires/wheels. I just had them balanced. It only shakes when hard accelerating. If I am easy on it, then smooth as can be. It gets worse with the RPM of the engine. I am thinking its in the tranny.
It still shifts smooth and I have been pulling 17 mpg on the interstate with it. So I know its acting correctly? Could I have blown something in the trans or ballooned the torque converter?
It just started the other day, I drove about 350 miles on vacation and noticed it when I went to come home. Like i said it only shakes when you lay in to the throttle, and it gets kinda violent.
View 14 Replies
I have a 1997 Ford F-150 XLT 4.6L 4x4 Auto and it's having an issue. My truck has recently developed a stutter when accelerating. It feels like a serious misfire and actually pulled a code for a misfire on cylinder 7 (although I haven't been able to get the code to appear again). The plugs are pretty new, I think I only have around 10k miles on them so i figured it might be the coil pack. I bought 2 new coil packs but only one was in stock so i replaced it on the drivers side bank (which controls cylinder 7) and it didn't fix my problem. When I first start the truck and drive it, it isn't very noticeable, but as I drive the truck for a few minutes, the stutter gets more violent. I will replace the other coil pack tomorrow, but I have my doubts it's the problem. It acts just like a bad coil pack.
View 9 Replies
I have 2002 4.2L F150 w/ Manual Transmission. The problem I have started about a week ago. I noticed it started to idle very rough and at times felt like it would almost stall if i didn't keep giving it some gas. Then a few days later it started to jerk/and buck intermittently while accelerating. I changed out the plugs and wires. My coil pack was replaced a year ago but was still under warranty so i installed a new one just in case. I cleaned and inspected the EGR valve and replaced the TPS. The rough idling seems to have cleared up but the jerking/and bucking still remains.
When the engine is cold the truck runs fine, and then as the engine starts to warm up it will jerk and buck while accelerating at any speed. Once the engine has reached its optimal temperature the jerking/bucking goes away and it runs smooth as silk. I can drive it for for a few hours with no issues whatsoever. As soon as the engine cools, the cycle starts all over again. I figured maybe the intake gaskets were on their last legs and when they heat up they seal tighter causing the engine to smooth out.
So I replaced the upper and lower plenum gaskets today and cleaned everything up. It still did not fix the problem.
View 2 Replies
I have a 98 f-150 4.6L 5spd that has a weird rattling noise coming from what sounds like the engine. The noise will only happen when the truck is in gear and under a load. It will not happen if I keep the RPM's low, unless I am going up a hill. When I rev the truck in neutral, the rattling noise isn't there. Also when I'm driving and hear the ratling noise it will go away when i push the clutch in(which im guessing takes the load off) but will come back when i let out on the clutch. Seems to happen most when I'm in gear and trying to accelerate.
View 9 Replies
2001 F150 5.4 v8 ... In the past few months my truck has been a bit strange, but in the past few weeks it's gotten to the point I'm nervous to drive it. Usually when shifting around 30-35, the engine revs up and stops accelerating and I have to take my foot off the pedal to make it return to normal. It doesn't do this after I do that, but the past time I tried to drive I couldn't get above 35 and the rpm was in the upper 2000s going at a constant 35. When I stop for any reason such as making a turn, when it shifts it lurches forward and I hear a loud clunk.
Naturally, I've checked all the fluids and fuses and they're all fine. The mechanic I regularly visit insists that nothing is wrong with it.
View 2 Replies
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
View 9 Replies
Truck started just fine this morning, was driving for about 15 minutes and it started to lose power going up a gradual incline. I didn't even think of it really and so I just pushed the pedal in a bit and no increase in power, in fact it bogged down. I let up and went back to the gas and same thing. This was barely pressing the pedal down. I got to the top of the incline and started back down a bit and gained speed (dropped from 55-60 to 40 at the crest) up to 55, hit level ground and started to lose power again, and it felt for the life of me like the truck was fighting for every ounce of power it could get. Everytime I would step on it it would bog down again. I nursed it to an appointment I had, and when I got done with that I started back home. Same thing. It would accelerate from a stop up to 30 (I've always been a laid back accelerater) and when I would read 35-45 it would start to dog again. I got it back home.
2nd issue: On the way home I had to stop at a highway crossing on a slight inline. There the truck started to shudder a bit. and if I would just touch the gas pedal it would bog down. I played with it a bit and got it to rev a bit. put it in reverse got away from the intersection and let it idle a bit when It died. started right back up, no problem. would play with the accelerator and same thing. I finally got it to rev a bit and 2 footed it back home slipping from neutral to drive.
View 14 Replies
