Ford F-150 - 1997-2003 :: 2001 F350 - Brake System Does Not Seem To Build Pressure When Truck Is Running
Aug 23, 2012
2001 F350 with 5.4 ... No leaking brake lines. The bad calipers have been replaced. Brake system doesnt seem to build pressure when the truck is running. The pedal gets stiff when the truck is shut off but when its started the pedal goes to the floor. Just put in a new booster and master cylinder. Flushed and blead all the lines several times now and got all the air out and am now getting a nice solid stream of fluid.
View 3 Replies
Advertisement
I'm having this weird problem with my car, 90% of the time it will start to run rich, until it reaches normal temp, to the point that I can smell it coming out from the exhaust. LTFT is at around -15% and it seems to go down after cruising for some time but will go back to negative at idle. My first suspect was the FPR so I checked it and found no gas smell on the vacuum hose, then I decided to run the engine with the vacuum hose disconnected and see if any fuel would come out, 5 minutes later and it was still dry.
There is a chance that the MAF sensor is bad, I'm 90% sure it is, because it will sometimes read 2.9-3.1 gps at idle and according to the rule of thumb of 1gps per liter of displacement, it shouldn't go that low but I might be wrong about it; I disconnected the MAF and the smell was still there, today while driving it was reading 5.45gps (A/C was on) and the smell was still present; car also feels sluggish from time to time only at normal operating temperature (which I assume is because of it running rich).
There is also a vibration felt through the steering wheel only while idling in gear at all temps. Today when I got home and after I turned off the engine I heard a noise like water was running. It was coming from the car so I tried to find where the noise was coming from and it's from the fuel tank. I removed the fuel cap and lots of air came out (or sucked in?). I reinstalled the cap and pressure started to build up almost immediately! I have a video, which I'm sharing, so you can see what I'm talking about; I was even able to hear the fuel tank expanding because of the pressure inside, not sure if you can hear it towards the end of the video (when I put the phone under the car). [URL] .....
It also happened today that I was cruising and the engine hit the rev limiter after I stepped on the gas (WOT) to overtake another car. I immediately removed the foot from the pedal and gave it less gas and it acted normal, no slipping from the transmission at any other time. There is one more thing that I'm not sure about it. Every morning, the engine will sputter for 1 or 2 seconds after starting it but it will be fine for the rest of the day. I once tried disconnecting different sensors from the engine and the only one that seemed to make a difference (it didn't sputter) was the TPS.
Things done so far:
- I replaced the EVAP purge solenoid (P0441 was present) back in february.
- Rubber pieces at charcoal canister also replaced, old ones were rotted to the point my hands would look black just by rubbing against the hoses.
- Upper intake manifold was also replaced by me in november last year.
- New NGK spark plugs and OEM spark plug wires last december.
- Cleaned the MAF sensor with MAF cleaner, no dice. Used brake clean, no change. It's a reman Cardone from autozone, which tells us it's 90% sure it's broken.
- New Duralast MAP sensor back in 2010 because a mechanic broke the original.
- 10qts transmission fluid and filter replacement 2 weeks ago.
- Fuel pump was also replaced back in 2009 maybe, can't remember the exact year. The old one would start making some kind of a hissing noise after prolonged driving.
NO DTC'S PRESENT. I once checked Mode $06 data with a mid-level scanner I have (AutoXray EZ-scan 6000) and saw a test had failed, I think it said something about the MAF and EGR. IHaven't connected my fuel pressure gauge tester. Since I can smell it running rich, I didn't think it would be necessary. I'm thinking that there could be a problem with the EVAP system that's causing the excessive pressure in the tank but I'm not sure what that could be. Is there any chance that the pressure is also causing the rich mixture?
View 7 Replies
I have a leak in my inter-cooler system. I have replaced all the hoses. Is there a reason I should not pressure test the system with 20psi? 2001 F350 7.3 turbo....
View 1 Replies
I have an 01 F150 SuperCrew with factory keyless entry fobs. I would like to be able to leave my truck running, take the keyless entry fob with me, and then lock the doors. Currently, the keyless entry fobs are disabled when the truck is running and I'd be locked out of the truck. I've had newer Fords that would allow the fobs to stay active with the vehicle running. Do this can be programmed into the truck?
View 5 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 Replies
My aunt recently gave me her 02 f150 for free because it got flooded and she didnt want to fool with it. she said it ran great before it got flooded. I flushed everything. oil, gas, and tranny. I blew water out the cylinders and replaced the spark plugs. I took the fuel injectors out and cleaned and cycled some b12 threw them. The truck starts and gets spark to every cylinder and is only running on 3. I can pull 3 plug wires off and the idle does not change. Idk what it could be but dead cylinders. I am afraid I am going to have to find a new engine. I am going to do a compression check later this week when I have time. I am new to fords so if there is anything I should check...
View 2 Replies
Started the morning with oil pressure gauge dropping to 0, gave it a few minutes checked oil, it was fine. Restarted truck, pressure went back to normal. Drove about another 30 miles pressure gauge would drop but would rise when hit accelerator. I was driving about 60mph, gauge went back to 0, check engine light came on and within a matter of seconds, a whining noise started, pulled over before i could completely stop, it died, and now won't crank.
View 6 Replies
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
View 9 Replies
Sometimes the truck is hard to get started and to keep running, Once it warms up it will run fine. The next time it is started it will start fine but when you are going down the road if I try to accelerate it will start backfiring and not pick up any speed. I am getting a lean code on both banks. I have changed the IAC, the throttle position sensor and mass air flow sensor. 2002 F150 with 6 cyl
View 1 Replies
2000 2WD 4.6L ... I was trouble shooting why the truck will not start after it has run for awhile then sits for about an hour. I was checking the connections on the solenoid switch on the fire wall when my wrench slipped and touched both terminals on the solenoid and the engine starter kicked in. I tightened the connection then tried to start the truck with no luck. so I tried leaving the key in the "ON" position and jumped the two terminals and the truck started. Does this tell me I have a bad solenoid switch?
View 6 Replies
I have a 1997 ford f150 V-6 4.2. My son was driving the truck on the expressway and it quit running. The toe truck has delivered the truck back to my house. The engine turns over but will not start. I shot gas into the engine with a spray bottle and the engine still would not start. Was going to check the coil for spark next. What to check first. Was thinking the problem could be the modulator or coil.
View 10 Replies
I have a 2001 F150 4.6L auto. This truck suddenly started running rough. Cleared all codes and re-scanned after starting truck. The codes are as follows; P0135, P0155, P0443, P0740, P0743, P0758, P1451, P1460, P1747, and P1760.
My question is; is it normal to have this many DTCs come up at once? Could my PCM be faulty causing this problem? Can you swap a pcm from the same year truck with the same options without reprogramming?
View 2 Replies
2001 F150 4.6. Just replaced all 4 oxygen sensors and spark plugs. Replaced rubber grommet on brake booster as it was leaking vacuum.
Truck is still running rough hesitating.
Pulled codes came up as PO141 oxygen sensor heater circuit. PO171 passenger side cylinders running lean. Fuel trim outside limits.
View 9 Replies
I have a 2000 F150 4WD 5.4 running Extremely rich to bank one. The O2 sensors for bank 1 are reading lean(0-50 mV) Bank two is completely unaffected. New plugs in Bank one, 3 new coils in bank one, all pvc lines checked with good vacuum. Previous codes : P0171, P0301-3. The Truck will barely move. Would a small leak up stream of the O2 sensors cause this?
View 10 Replies
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 Replies
I have a 97 F150, 2wd, 4.6, auto bought for a great price agout 3 months ago.... I installed a cold air intake (air raid) and a throttle body spacer with the swirling cuts.
Since the cold air intake add, the truck occasionally makes a load "roaring" sound from the intake system. At same time rpms increase 500-1000 rpms...
it doesn't do it all the time, mostly at low throttle, and a quick jab on the accelerator usually stops it. sometimes such as when parking, holding the brake and applying a bit of throttle with load from the brake will also stop it.
Guys at local garage seem to think it has something to do with lower outside temps, (denser) and addition of cold air intake. it made the noise before the throttle body spacer.
View 4 Replies
I've done everything I can think of, ive replace the starter, batteries and altenator, both batteries have at least 12.30 volts when taken out and checked, but i turn the key and it will have power then try to start and whole system dies and wont come back on, I've cleaned the terminals and posts to shiny and the ground connections but its still not getting power.
View 1 Replies
I have a leak in my inter-cooler system. I have replaced all the hoses. Is there a reason I should not pressure test the system with 20psi? 2001 F350 7.3 turbo
View 4 Replies
I have a 2001 F350 and over the past few nights the horn has started honking once randomly. It always only honks once but will do it several times a night (may be more that I don't hear). I'm thinking that this has something to do with the alarm maybe? I can't afford to take it to the shop at the moment (nor any moments in the foreseeable future, come to think of it) and am hoping that its something that I can fix myself?
I'm having other miscellaneous electrical type issues, but don't know it there are related at all. For example, the power locks don't work (they try to, but don't seem to have enough power), the overhead console that digitally displays the outside temp/mpg/etc. stopped working suddenly and the lighter/power plug outlet stopped working, but I was able to fix this by replacing the fuse.
View 11 Replies
Just recently got a sweet deal on an 01 Lariat with a very low mileage 5.4L. I almost didn't purchase it because the oil pressure gauge will not read when you start the engine. Sometimes it will sometimes not.
When it does read, it is just past half which is the normal reading. When it doesn't read, it shows zero and the light is on. The engine runs fine either way, and the previous owner said it has been that way for years. The engine has been well cared for, and has been running Mobile 1 full synthetic for most of the 80k miles. The oil was not overly dirty at purchase, so I figured it to be a loose connection. I suffer from the cold solder joints that these trucks are plaqued with, as evident by the intermittent odometer reading. Do you think the oil gauge issue is the same thing? A cold solder joint? Or should i just start with a new sender?
View 13 Replies
