Ford F-150 - 1997-2003 :: 2001 - Codes Pops Up - Cylinder 1 Misfire?


Dec 28, 2015

2001 f 150 5.4 liter with it being code pops up saying cylinder one misfire, I've charge coil and spark plug ran great for awhile now starting to act up again. Got coil check and says still good and look at spark plug and looks still in good shape being just replace two weeks ago. It's running fine but if it sits over night and I get in and start it and begins to shake when I but it in drive and don't even need to move the truck just place it in drive with foot on break. I drive it awhile and it stops and runs fine?

View 9 Replies

Advertisement

Ford F-150 - 1997-2003 :: CEL Codes P0304 / P0456 / P0171 - Misfire On Cylinder 4

So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:

P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?

Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.

Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?

View 7 Replies

Ford F-150 - 1997-2003 :: Codes For Large EVAP Leak / Cylinder 6 Misfire / Bank 2 Lean

Here are the codes I'm getting:

P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean

are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st

View 4 Replies

Ford F-150 - 1997-2003 :: 2001 - Misfire On Cylinder 6 - CEL On?

I have an 01 5.4 Triton with engine light on I put it on the scanner and it read miss fire on cylinder 6 and 1 I changed the cops and plugs boots and spring erased the codes but the check light is back on and scanner is say miss fire on same two cylinders u can hear it in the exhaust u can smell gas when sitting at an idle around 40 MPH has a slight engine shake goes away when u accelerate I am not sure what else to do some one told me to check for vac leaks and fuel pressure.

View 14 Replies

Golf IV / Jetta IV :: 2001 GLS 1.8T - Cylinder 1 Misfire / O2 Sensor Codes

I bought a 2001 golf gls 1.8T (AWW) about a month ago and it was running pretty bad, was throwing some codes, cylinder 1 misfire and some o2 sensor codes, I replaced the coil packs and spark plugs and then cleaned the MAF. It was still running bad ,rough idle and power loss. I figured it had to be some kind of vacuum leak, I replaced the PCV valve, cleaned the intercooler and put on a silicon TIP. Still had some rough idle and power loss, checked for vacuum leaks, using the good ole starter fluid method and found my intake manifold was leaking so I replaced that gasket. STILL rough idle and power loss, now I'm pulling codes for o2 sensor and a misfire in cylinder 3. My question is, should I replace my pre-cat o2 sensor or replace my MAF sensor? Or are there other things that should also be checked/replace.

View 5 Replies

Elantra XD (2001-06) :: Random Misfire On Cylinder 2 / 3 And EVAP Codes

Trying to troubleshoot my 2001 Elantra (173k). I'm having intermittent trouble codes being set and I'm wondering if they may be related:

P0302
P0303
P0446

The cylinder 2 and 3 misfires are relatively recent. Plugs and wires are visually ok (and not that old). I swapped plugs 1 and 4 with 2 and 3 to see if the plugs are bad. It took 3-4 days, but the P0303 set again (and it's very intermittent - car will noticeably lose power for a few seconds, code set, then run fine for several days). I also sprayed carb cleaner on the intake manifold gasket with no change in engine idle, so the gasket appears to be intact.

I had read in a forum somewhere that the misfires could be related to a vacuum leak, which could also be setting the P0446 code. I removed the charcoal canister and inspected the lines - visually ok.

I bench-tested the canister control valve and it did operate, though I noticed some charcoal blocking the valve so it would not close all the way when energized. I used compressed air to blow the debris out of the valve and it appears to close properly now.

I went to hmaservice.com and noticed there are no instructions for the P0446 DTC. I've been using a Haynes manual instead. For quite some time now when refueling, the fuel nozzle shuts off every few seconds (I have to slowly put the fuel in to avoid).

Some questions:

- Can these codes be related?
- Based on my symptoms, should I replace the canister control valve? What about the charcoal canister and the charcoal air filter - should those be replaced as well?
- What else should I check?

View 9 Replies

Ford F-150 - 1997-2003 :: Misfire On 7 Cylinder

I have changed the COP and the injector as well as the spark plug. I am still having a misfire on #7 cylinder....

View 8 Replies

Ford F-150 - 1997-2003 :: Unexplained Misfire On Cylinder 1 And 5

My truck has developed a misfire on cylinders 1 and 5. The OBD2 scanner at autozone says code P0300, Po301 and P0305. I bought a new set of plugs and wires. Problem still there. I then replaced the both coils. Problem is still there. Is there a control module or something that could kill those 2 cylinders like on the older trucks with distributors?

View 7 Replies

Ford F-150 - 1997-2003 :: Engine Misfire On Cylinder 4 And 6

I have 97 150 it has a misfire on cylinder 4 and 6. I put new coil packs on and new plug wires. Spark plugs are only a year old. what else it could be?

View 1 Replies

Ford F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire

So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.

Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:

Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6

I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.

View 14 Replies

Ford F-150 - 1997-2003 :: 1999 - Persistent Misfire In Cylinder 5

I have a 1999 F-150 4.2L with a misfire in #5 cylinder. I have replaced plugs, plug wires and coil pack, checked compression (147 psi) and ran 4 cans of seafoam thru it and still getting misfires on acceleration. It'a a 5 speed and it sounds rough and runs a lil rough as I go thru the first 3 gears, then it runs good as I get up to speed and cruises fine at 80mph. I'm thinking a bad fuel injector???

View 7 Replies

Ford F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1

My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.

I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.

I thought about picking up a kit to check the injector pulse.

View 8 Replies

Ford F-150 - 1997-2003 :: Misfire On Cylinder 8 Usually In Mornings Or If There Was Moisture In Air

I have a 2000 4.6 2wd f 150 ext cab. I started to have a misfire problem on cylinder 8 every so often usually in the mornings or if there was moisture in the air. It gradually got worse over time and when I got it read it had gone to cylinders 5,7, and 8 with the misfire codes which said misfire cylinder whichever primary/secondary circuit misfire and it has now gone to cylinder 2 as well. I replaced all the coils and the plugs with autolite platinum plugs and new coils for this motor and the problem has not changed. It came right back after I cleared the codes, what possible causes I could check out....

View 9 Replies

Ford F-150 - 1997-2003 :: P0307 Fault / Misfire On Cylinder 7

I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently got the P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. Any clues to the cause of my problem?

View 5 Replies

Ford F-150 - 1997-2003 :: P0308 Cylinder 8 Misfire Detected

Where do I start? Pull the coil?

View 5 Replies

Ford F-150 - 1997-2003 :: Misfire On Cylinder 3 And 8 After Putting New Trans

I've got a 1997 f150, 4.6. It sat for year and a half, trans went out and it wasn't my primary vehicle so wasn't to worried about fixing it. Until now, well got a new trans put in it, fired it up. And had a misfire, #3 and #8. Changed plugs and wires, same thing. Getting spark at the plug. So I changed both injectors, still nothing! I'm kind of stumped now.

View 4 Replies

Ford F-150 - 1997-2003 :: Code PO304 - Cylinder 4 Misfire

I have a '98 F150 4X2 extended cab with a 4.2l with 233K on it. I have no problem with drivability when I drive 5 miles to work. However, a couple of weeks ago when I had to drive 15 miles to the liquor store to get what I needed (I live in a dry county) I got back into my truck, started it and drove of. It drove like crap like I lost a cylinder. Drove it back home those 15 miles, let it cool off, put my scanner on it and got a PO304 code and I think a PO174 (bank 2 lean) code. Went to the #4 cylinder and found the plug had loosened up.

Tightened it back up, cleared the codes, and went through my normal weekly routine of driving to work with no problem. Made a booze run the next weekend and the same thing happened. Limped back home and found another PO304 code. Found the plug to be tight and in good condition but changed all the plugs since they were cheap copper core and had 20K on them. The wires only have 20K on them, too. Installed platinum plugs, drove all week 5 miles to work and back just fine. Made another 15 mile run yesterday and the same crap happened all over again after I got out of the store and drove home.

View 1 Replies

Ford F-150 - 1997-2003 :: Misfire Error Codes - CEL On?

Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:

"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "

So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors???

I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?

View 14 Replies

Ford F-150 - 1997-2003 :: Misfire On Cylinder 3 (P0303) But Only During Towing With Ethanol

I drive a Supercrew F150 5.4L XLT 02 since 9 years, I put a Fuelflex module since 8 years, since some months I Misfire on cylinder #3 (P0303) but only during towing with Ethanol (over 2000/2500 rpm), when I drive on gas all is fine, I changed Flexfuel modul, plugs, coils, header gasket, without any positive results, it's very curious to have the problem only with ethanol (E85), I can drive very hard and at high speed with just the truck, but with a trailer as soon as I ask more power i lose one cylinder, with misfire...but like I said only on ethanol? I know engine needs more ethanol than gas, so I go check fuel pressure and maybe try to change fuel injector...

View 8 Replies

Ford F-150 - 1997-2003 :: 1999 - Ride Rough - Misfire On Cylinder 3?

I'm working on my 99 f-150. I replaced all my spark plugs and coils after I got a misfire on cylinder 3 reading on the scanner. The truck was running ok but two weeks later it started to ride rough again I checked the scanner and got the same reading for a misfire on cylinder 3. Why its giving me the same misfire again? Could my injector cause that misfire? What about the egr valve?

View 8 Replies

Ford F-150 - 1997-2003 :: 1998 - Cylinder 1 Misfire / Code P0301

I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.

This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.

Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.

I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.

View 14 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved